Getting Started; Accessory List; Turning Power On And Off; Detaching And Attaching The Front Panel - Alpine cda-9886 Quick Reference Manual

Getting Started
Rotary encoder
:.:::: (OPEN) MUTE
~
lENT
~IESC
FISETUP
Accessory List
• Head unit 1
• Power cable 1
• Mounting sleeve 1
• Carrying case 1
• Bracket key 2
• Screw (MS x 8) 4
• Remote Control 1
• Battery (AAA size) 2
• Owner's Manual 1 set
Turning Power On and Off
Press SOURCE/<!> to turn on the unit.
• The unit can be turned on by pressing any other button except
:.:::: (OPEN).
Press and hold SOURCE/<!> for at least 2 seconds to turn
off the unit.
• Thefirst time power is turned on, the volume will start from level 12.
Detaching and Attaching the Front Panel
Detaching
1
Turn off the unit power.
2
Press:':::: (OPEN) to open the front panel.
To close the front panel, press the left side until it locks as
shown in the figure below.
3
Grasp the front panel firmly, slide to the left
0 ,
and then pull
8
to remove.
• The front panel may become hot in nonnal usage (especially the
connector tenninals on the back of the front panel). This is not
a
malfunction.
• To protect the front panel. place it in the supplied carrying case.
• When detaching the front panel. do not apply excessive force as it
may result in malfunction.
• Do not leave the front panel open, or drive the car with the panel
open as it may result in an accident or malfunction.
Attaching
1
Insert the right side of the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
2
Push the left side of the front panel until It locks
firmly into the main unit.
• Before attaching the front panel, make sure that there is no dirt or
dust on the connector tenninals and no foreign object between the
front panel and the main unit.
• Attach the front panel carefully, holding the sides ofthe front panel to
avoid pushing buttons by mistake.
Initial System Start-Up
Be sure to press the RESET switch when using the unit for the first
time, after changing the car battery, etc.
1
Turn off the unit power.
2
Press:':::: (OPEN) to open the front panel, and then
remove it.
3
Press RESET with a ballpoint pen or similar pointed
object.
~
I
=
.
I
RESET
switch
7-EN
Getting Started
Rotary encoder
:.:::: (OPEN) MUTE
~
lENT
~IESC
FISETUP
Accessory List
• Head unit 1
• Power cable 1
• Mounting sleeve 1
• Carrying case 1
• Bracket key 2
• Screw (MS x 8) 4
• Remote Control 1
• Battery (AAA size) 2
• Owner's Manual 1 set
Turning Power On and Off
Press SOURCE/<!> to turn on the unit.
• The unit can be turned on by pressing any other button except
:.:::: (OPEN).
Press and hold SOURCE/<!> for at least 2 seconds to turn
off the unit.
• Thefirst time power is turned on, the volume will start from level 12.
Detaching and Attaching the Front Panel
Detaching
1
Turn off the unit power.
2
Press:':::: (OPEN) to open the front panel.
To close the front panel, press the left side until it locks as
shown in the figure below.
3
Grasp the front panel firmly, slide to the left
0 ,
and then pull
8
to remove.
• The front panel may become hot in nonnal usage (especially the
connector tenninals on the back of the front panel). This is not
a
malfunction.
• To protect the front panel. place it in the supplied carrying case.
• When detaching the front panel. do not apply excessive force as it
may result in malfunction.
• Do not leave the front panel open, or drive the car with the panel
open as it may result in an accident or malfunction.
Attaching
1
Insert the right side of the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
2
Push the left side of the front panel until It locks
firmly into the main unit.
• Before attaching the front panel, make sure that there is no dirt or
dust on the connector tenninals and no foreign object between the
front panel and the main unit.
• Attach the front panel carefully, holding the sides ofthe front panel to
avoid pushing buttons by mistake.
Initial System Start-Up
Be sure to press the RESET switch when using the unit for the first
time, after changing the car battery, etc.
1
Turn off the unit power.
2
Press:':::: (OPEN) to open the front panel, and then
remove it.
3
Press RESET with a ballpoint pen or similar pointed
object.
~
I
=
.
I
RESET
switch
7-EN