Models Icb424 And Icb424Fs Installation - Sub-Zero ICB424 Installation Instructions Manual

Models ICB424 and ICB424FS Installation

Models ICB424 and ICB424FS Installation
The Sub-Zero model ICB424FS wine storage unit is
designed to be attractive in a stand alone setting. It can
also be slid into surrounding cabinetry with clearance
dimensions slightly different than the standard built-in
model ICB424.
Make sure that the finished rough opening where the wine
storage unit is to be installed is properly prepared. Refer
to the installation specifications illustration for rough
opening dimensions, door swing clearance and electrical
placement for models ICB424 and ICB424FS.
IMPORT NT NOTE: To operate properly, the door must
open a minimum of 90°. Use a minimum 76 mm filler in
corner installations to assure a 90° door opening. llow
enough clearance in front of the unit for full door swing.
IMPORT NT NOTE: Make sure the floor under the unit is
level with the surrounding finished floor.
Do not load wine into the wine storage unit until the
installation is complete.
TOP VIEW
610 mm
ROUGH
OPENING
DEPTH
ROUGH OPENING
WIDTH
610 mm
MODEL ICB424
619 mm
MODEL ICB424FS
MODEL ICB424
ANTI-TIP BRACKET
LOCATE ELECTRICAL
WITHIN SHADED AREA
114
mm
394 mm
E
64 mm
MODEL ICB424FS
FRONT VIEW ANTI-TIP BRACKET
145˚
90˚
MAXIMUM
DOOR SWING
644
mm
660 mm 1118 mm
DOOR CLEARANCE DOOR CLEARANCE
Door swing clearances are based on stainless steel door and
handle dimensions.
Electrical Requirements
separate circuit, servicing only this appliance, is
required. The electrical supply should be located within
the shaded area shown in the illustration below.
The unit is equipped with a detachable power supply cord
with a grounded (earthed) plug which must be plugged
into a mating grounded (earthed) wall receptacle. Follow
local codes and ordinances when installing the receptacle.
IMPORT NT NOTE: ground fault circuit
interrupter (GFCI) is not recommended and may cause
interruption of operation.
IMPORT NT NOTE: The unit is equipped with an appliance
876 mm
ROUGH
inlet type device. This allows easy replacement of the
OPENING
HEIGHT
power cord. The appliance inlet is located on top of the
870 mm
unit on the compressor shroud.
MINIMUM
HEIGHT
REQUIRED
Electrical Requirements
Power Supply 220-240 V C, 50/60 Hz
Circuit Breaker
Receptacle grounding-type (earthed)
LEFT SIDE
OF OPENING
606 mm
51
mm
394 mm
76 mm
645 mm
FRONT VIEW
Location of electrical supply.
Electrical ground (earthing) is required on this appli-
ance. Do not defeat the grounding (earthing) nature of
the power cord.
The outlet must be checked by a qualified electrician
to be sure that it is wired correctly. Verify that the
outlet provides the proper voltage and is properly
grounded (earthed).
lways shut power off at the circuit breaker before
performing any installation, service or maintenance.
Electrical
Shock
Hazard
Plug power cord directly into a properly
grounded (earthed) outlet.
Do not defeat the grounding (earthing)
nature of the plug.
Do not use adapter or extension cord.
Failure to follow these instructions could
cause serious injury or death.
See installation instructions
10 amp
Unpacking and Moving
Uncrate the unit, remove its wood base and discard the
shipping bolts that hold the wood base to the bottom of
the unit. Remove all packing materials and tape.
IMPORT NT NOTE: Do not discard the kickplate, anti-tip
bracket and hardware. These items will be needed for the
installation.
ll roller-assembly wine shelves should be removed to
reduce weight and prevent them from rolling. To remove,
pull the shelf out to its full extension, gently and evenly lift
up on both sides of the front of the shelf and remove.
Reverse the procedure to reinstall the shelf.
Use an appliance dolly to move the wine storage unit.
Position the dolly at the back of the unit to prevent
damage to finished surfaces.
Before moving the wine storage unit in to position,
protect any finished flooring with appropriate mate-
rials and secure the door closed.
5
www.subzero.com