Models Icb427 And Icb427R Installation - Sub-Zero ICB424 Installation Instructions Manual

Models ICB427 and ICB427R Installation

Models ICB427 and ICB427R Installation
Models ICB427 and ICB427R Installation
Make sure that the finished rough opening where the wine
storage unit is to be installed is properly prepared. Refer
to the installation specifications illustration for rough
opening dimensions, door swing clearance and electrical
placement for models ICB427 and ICB427R.
IMPORT NT NOTE: To operate properly, the door must
open a minimum of 90°. Use a minimum 51 mm filler in
corner installations to assure a 90° door opening. llow
enough clearance in front of the unit for full door swing.
IMPORT NT NOTE: Make sure the floor under the unit is
level with the surrounding finished floor.
Do not load wine into the wine storage unit until the
installation is complete.
635 mm
ROUGH
OPENING
DEPTH
TOP VIEW
686 mm
2032 mm
ROUGH OPENING ROUGH OPENING WIDTH
HEIGHT
TO FINISHED
FLOORING
2019 mm
MIN HEIGHT
REQUIRED
LOCATE ELECTRICAL
WITHIN SHADED AREA
114
mm
394 mm
E
ANTI-TIP BRACKET
64 mm
FRONT VIEW
105˚
90˚ MAXIMUM
DOOR SWING
648
mm
711 mm 889 mm
DOOR CLEARANCE DOOR CLEARANCE
Door swing clearances are based on stainless steel door and
handle dimensions.
Electrical Requirements
separate circuit, servicing only this appliance, is
required. The electrical supply should be located within
the shaded area shown in the illustration below.
The unit is equipped with a detachable power supply cord
with a grounded (earthed) plug which must be plugged
into a mating grounded (earthed) wall receptacle. Follow
local codes and ordinances when installing the receptacle.
IMPORT NT NOTE: ground fault circuit
interrupter (GFCI) is not recommended and may cause
interruption of operation.
IMPORT NT NOTE: The unit is equipped with an appliance
inlet type device. This allows easy replacement of the
power cord. The appliance inlet is located on top of the
unit on the compressor shroud.
Electrical Requirements
Power Supply 220-240 V C, 50/60 Hz
Circuit Breaker
Receptacle grounding-type (earthed)
LEFT SIDE
OF OPENING
64
mm
330 mm
114
mm
FLOOR
6 mm
FRONT VIEW
606 mm
Location of electrical supply.
Electrical ground (earthing) is required on this appli-
648 mm
ance. Do not defeat the grounding (earthing) nature of
the power cord.
The outlet must be checked by a qualified electrician
to be sure that it is wired correctly. Verify that the
outlet provides the proper voltage and is properly
grounded (earthed).
lways shut power off at the circuit breaker before
performing any installation, service or maintenance.
Electrical
Shock
Hazard
Plug power cord directly into a properly
grounded (earthed) outlet.
Do not defeat the grounding (earthing)
nature of the plug.
Do not use adapter or extension cord.
Failure to follow these instructions could
cause serious injury or death.
See installation instructions
10 amp
Unpacking and Moving
Uncrate the unit, remove its wood base and discard the
shipping bolts that hold the wood base to the bottom of
the unit. Remove all packing materials and tape.
IMPORT NT NOTE: Do not discard the kickplate/grille,
anti-tip bracket and hardware. These items will be needed
for the installation.
ll roller-assembly wine shelves should be removed to
reduce weight and prevent them from rolling. To remove,
pull the shelf out to its full extension, gently and evenly lift
up on both sides of the front of the shelf and remove.
Reverse the procedure to reinstall the shelf.
Retract the front leveling legs to allow you to move the
unit more easily during installation. You will extend the
leveling legs when the unit is in its final position to reduce
the possibility of the unit tipping forward.
Use an appliance dolly to move the wine storage unit.
Position the dolly at the side of the unit to prevent damage
to finished surfaces.
Before moving the wine storage unit into position,
protect any finished flooring with appropriate
materials.
10
10