Table of Contents
Advertisement
Removing and maintaining
the accessories
Before you start
Remove the power plug from
the socket.
Failure to remove the plug
may result in electric shock.
Wait at least 10 minutes before you replace
the power plug.
The refrigerator will not operate if the plug is
replaced immediately after it is removed.
Shelf removal
1
Set the left and right levers
to the "Lock" position.
Lever
Lever
2
Hold the front of the Revolving
Shelf with both hands, and while
slightly lifting up the rear, push
the Revolving Shelf to the rear.
(Guide the rear of the shelf to get
on the left and right rails.)
3
Lift the front of the Revolving
Shelf, and remove from the
refrigerator. (Pass it on the
top of the left and right rails.)
AUTO Shelf
Shelf removal
1
Move the lever to the right end.
2
Strongly push up each support,
one by one. (4 locations.)
(A clicking
sound is made
when the support
disengages.)
If the supports are firmly set
and difficult to disengage, tilt
the inner tabs to the inner side.
3
Remove from the refrigerator.
24
Wipe the accessories clean with a soft piece of cloth wet with slightly warm water or
remove them to wash with water.
For deposits sticking hard, wet a piece of cloth with dishwashing agent diluted with
Warning
water and wipe off the deposits. Then wipe out with a piece of cloth wet with water.
Be sure to wipe off all oily deposits. Oily deposits, if left unattended, can cause
plastic parts to break.
Note
Shelf installation
1
Make sure that the levers are in
the "Lock" position.
2
Place the Revolving Shelf in the
refrigerator, put it on the left and
right rails, and pass it on the rails to
the rear.
3
While passing the Revolving Shelf through
the grooves of the left and right rails and
pulling it to the front, lower the rear of the
Revolving Shelf. (When pulling the
Revolving Shelf to the front, make sure
that it stops in the grooves of the rails.)
(Do not disassemble the AUTO Shelf, or use chemicals such as grease to clean it. Doing so may cause a malfunction.)
Shelf installation
1
Make sure that the lever
is on the right side.
2
Make sure that the 4 metal stoppers are fitted,
and place the shelf lightly so that the 4
supports are aligned with the 4 metal stoppers.
3
Push in each of the 4 supports in turn
from above. (A clicking sound is made.)
4
Move the lever to the left and right and
check that the AUTO Shelf is kept level
when moved up and down. (If the shelf is
not kept level, remove the AUTO Shelf
and repeat steps
Maintenance and Cleaning
Do not use an alkaline- or alkalescent-base kitchen detergent,
polishing compound, a powder detergent, alcohol, benzene,
paint thinner, petroleum, acid, hard brush or hot or boiled water.
They will cause damage to plastic parts (door handles, cap, cases, etc.) and coating on
the surfaces such as the doors.
Revolving Shelf
Lever
Lever
1
4
to
)
Tray removal
1
Set the lever to the "Lock" position.
2
Hold the stopper knob
in the middle of the
Revolving Shelf, and
remove the stopper by
turning it in the
direction of the arrow.
3
Insert your hand from the
center of the Revolving
Shelf, and lift up the tray.
*There is a risk of the tray
falling.Move it slowly.
4
There is a risk of the tray
falling.Move it slowly.
When installing the tray, position the tray in
the direction shown in the figure. Installing
in other directions will result in incorrect
installation, and the part
may fall out.
Tray removal
1
Push up the 3 tabs on the rear of the
tray with your finger.
2
Lift up the rear of the tray until the 3 front
tabs and the 2 side tabs disengage.
*There is a risk of the tray falling.
Move it slowly.
3
Pull out with both hands.
Two-way flexishelf
Push in and
lift up.
Stopper
1
2
Hide quick links:
Advertisement
Table of Contents
