Sony PXW-X400KC Operating Instructions Manual page 15

000 15
1. Overview: Screen Display
7
1 2 3 4 5 6
37
36
35
34
33
32
31
30
29
28 27 26
1.
Extender indicator
Displays the status of the digital extender function
and lens extender function.
EX: Appears when the lens extender function is ON
X2D: Appears when the digital extender function
(×2) is ON
X3D: Appears when the digital extender function
(×3) is ON
X4D: Appears when the digital extender function
(×4) is ON
EX2D: Appears when both the lens extender
function and digital extender function (×2) are
ON
EX3D: Appears when both the lens extender
function and digital extender function (×3) are
ON
EX4D: Appears when both the lens extender
function and digital extender function (×4) are
ON
Turn the digital extender on/off using an
assignable switch assigned with the Digital
Extender function.
8 9
10 11 12
25 24
[Note]
The digital extender cannot be turned on when Slow & Quick
Motion is enabled.
2.
Zoom position indicator (with lens mounted)
Displays the zoom position of the zoom lens in the
range 0 to 99.
3.
Color temperature indicator
Displays the color temperature of the white
balance.
4.
Focus position indicator (with lens mounted)
Displays the focus position as a distance to the
subject (unit: meters).
5.
Iris position indicator (with lens mounted)
Displays the iris position setting.
6.
Electric color temperature filter indicator
Appears when the CC5600K function is on.
7.
Depth of field indicator (serial lens mounted)
Displays the depth of field using a bar. The units
for display are set using Operation >Display On/Off
>Lens Info in the setup menu, and can be set to
meters or feet.
8.
Recording mode indicator
Displays the following recording operation states
of the camcorder.
13 Indicator Meaning
14
Rec During recording
15
Stby Recording standby
16
Cont Rec
Clip continuous recording in
17
18 progress
19
Cont Stby Recording standby in clip continuous
20
recording mode
21
22
S&Q Rec
Recording in progress in Slow &
Quick Motion mode
23
S&Q Stby Recording standby in Slow & Quick
Motion mode
Rec
Recording in picture cache mode
Cache
Recording standby in picture cache
mode
Int Rec Recording in progress in Interval Rec
mode
Int Stby Recording standby in Interval Rec
mode
Int Stby
Recording paused in Interval Rec
mode (during pause intervals)
Sml Rec
Recording in progress in Simul Rec
mode
Sml Stby Recording standby in Simul Rec
mode
CALL Call received from external
connected device
Green tally is displayed when the camcorder is in
the following states.
ˎ Maintenance >Camera Config >HD-SDI Remote ˎ
I/F is set to Green Tally in the setup menu and a
recording control signal is output from the SDI
OUT connector.
ˎ Green tally signal received (when a camera ˎ
adaptor is mounted on the camcorder and a
camera extension unit is connected)
9.
Wireless receiver function indicator
Displays "W" when a slot-in receiver is attached to
the camcorder, and displays the reception level
for each channel that can be used by the receiver
(1ch, 2ch, or 4ch).
Normal: Displays the strength of the received
signal level by the number of white segment
indicators.
Analog receiver muting/Digital receiver error rate
warning: Displays the strength of the received
signal level by the number of gray segment
indicators.
If the received level exceeds the peak: Displays "P"
in place of the indicator.
1)
Receiver battery is low: The corresponding channel
number and indicators flash.
1)
1) When using the DWR-S02D
10.
S&Q Motion (Slow & Quick) frame rate
indicator
Displays the shooting frame rate when the
camcorder is set to Slow & Quick Motion recording
mode.
11.
GPS indicator (page 54)
12.
Battery capacity/voltage display
Displays the following indicators according to the
type of battery power source.
Battery type Indicator
Info battery Battery remaining capacity
icon and remaining recording
time
Anton/Bauer Remaining battery capacity (%
battery indicator)
Other batteries Input voltage
13.
Recording format (picture size) indicator
Displays the picture size of clips recorded onto SxS
memory cards.
14.
Recording format (system frequency and
scan method) indicator
Displays the currently configured camcorder
system frequency and the recording format scan
method.