AMX MIO-R3 Instruction Manual
Hide thumbs
Also See for MIO-R3:
- Quick start manual (2 pages) ,
- Operation/reference manual (34 pages) ,
- Datasheet (2 pages)
Related Manuals for AMX MIO-R3
Summary of Contents for AMX MIO-R3
- Page 1 IN STR U CT IO N MAN U AL M I O - R 3 M I O M O DE RO R - 3 R E M O TE KI T MI O- R3 MI O- R3- CC...
-
Page 2: Important Safety Instructions
COPYRIGHT NOTICE AMX© 2015, all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of AMX. Copyright protection claimed... -
Page 3: Table Of Contents
Table of Contents Table of Contents Overview ......................5 The Mio Modero® R-3 ....................... 5 FCC Compliance ........................ 5 Specifications ........................6 Touch And Tilt Sensor ....................... 6 Inserting or Replacing the Lithium-Ion Battery..............6 Battery Low Indicator ..........................7 Installing Custom Buttons .................... - Page 4 Table of Contents SLEEP-# ....................................15 @SSL...................................... 15 @SST ..................................... 15 @SWK ....................................15 ^TXT ...................................... 15 Send_Commands......................16 @BRT ..................................... 16 ^CFG ...................................... 16 ^UNI ...................................... 16 ZAP!......................................16 ZIGC ....................................... 16 ZIGP ....................................... 16 ^FML ...................................... 17 ^FML S/D/L/#..................................17 ^GLY.......................................
-
Page 5: Overview
Overview Overview ® The Mio Modero The Mio Modero R-3 is an elegant hand-held remote providing ZigBee Wireless control of a wide coverage area, two-way communication and control of every system device. Unique device IDs allow the R-3 to operate independently of other R-3 remotes within the same area. -
Page 6: Specifications
• Storage Temperature: -20° to 70° C (-4° to 158° F) • Relative Humidity: 5% to 85% Included Items: • Mio-RBP Rechargeable Lithium-Ion Battery (FG147-10) Other AMX Equipment • DB-9 extension cable (FG10-727) • Programming Cable - a 3 wire, 2.5 mm stereo jack (FG10-817) • Custom engraving (FG147-01) •... -
Page 7: Battery Low Indicator
Overview Lithium-Ion Battery Correct path for battery wires and connector Rechargeable Battery Port Connection Rear view - Battery Compartment Rechargeable Battery Port on The Mio Remote FIG. 2 NOTE: Make sure to inset the battery wires in the case as shown in FIG. 2, or the wires may be damaged when replacing the battery door. -
Page 8: Patents
Overview Turn the unit over so that the buttons are facing you. Lift the top assembly away from the PCB. If necessary, push out the standard buttons from the front of the top assembly. Drop on your custom button pad and verify the alignment with the guide posts on the PCB. Place the top assembly back down on the PCB and return the unit over, exposing the 6 screw points. -
Page 9: Setup Mode
Setup Mode Setup Mode Overview The Setup mode allows you to set the following device features on the Mio R-3: Transmit Mode Timeout Adjustment Download Mode Debug Mode Firmware Version Device ID LED Awake Brightness ... -
Page 10: Firmware Version
ZigBee Personal Area Networks, refer to the NXR-ZGW/-ZRP-PRO Operation/Reference Guide, available from www.amx.com.) In order to display the NetLinx Master IP and ZigBee gateway EUI addresses, press the Move Up arrow on the scroll wheel to scroll up. and pressing the Move Down arrow will scroll down. When finished, press Exit to save the Extended PAN ID and channel information and leave Setup mode. -
Page 11: Programming The Mio R-3
The programming jack is used for communication between the device and KeypadBuilder. The programming jack uses a three-wire, 2.5mm stereo jack. The programming cable (FG10-817) may be ordered from AMX if you do not currently possess one. The Mio R- 3 communicates at a 115200 baud rate. -
Page 12: Channel Codes
Programming The Mio R-3 Channel Codes The following table gives the channel codes associated with each button on the Mio R-3. Thirty-six of the buttons change channel codes based on what button was last pressed. Nine of the buttons always emit the same channel code regardless of what button was last pressed. -
Page 13: Serial Commands
Programming The Mio R-3 Serial Commands The Mio R-3 remote supports a few commands that can be uploaded to the device using a terminal program such as HyperTerminal. These commands are not needed for normal usage or programming of the remote. Serial Commands @BRT Set Brightness level - This command can be used to customize the brightness of the red LEDs that backlight the power... -
Page 14: Gly
'^GLY-<variable text address range>,<glyph number>'" Example: SEND_COMMAND Panel,"'^GLY-1,10'" Set a glyph with index 10 to the Mio-R3 display. Note: This only works if a glyph f ile has been loaded from KeypadBuilder. IRMODE #\ Sets the IR transmission frequency to either 38 or 455KHz... -
Page 15: Sho
Programming The Mio R-3 Serial Commands (Cont.) ^SHO Show or hide text with a set variable text range Syntax: "'^SHO-<variable text address range>,<command value>'" Variables: • variable text address range = 1 - 6; the address range corresponds to the dynamic line number. •... -
Page 16: Send_Commands
Programming The Mio R-3 Serial Commands (Cont.) ^UNI Set Unicode text. For the ^UNI command (%UN and ^BMF command), the Unicode text is sent as ASCII-HEX nibbles. Syntax: SEND_COMMAND <DEV>,"'^UNI-<vt addr range>,<button states range>,<unicode text>'" Variables: • variable text address range = 1. •... -
Page 17: Fml
'^GLY-<variable text address range>, <glyph number>'" Example: SEND_COMMAND Panel,"'^GLY-1,10'" Set a glyph with index 10 to the Mio-R3 display. Note: This only works if a glyph f ile has been loaded from KeypadBuilder. Mio Modero R-3 Remote - Instruction Manual... -
Page 18: Jst
Programming The Mio R-3 Send_Commands (Cont.) ^JST Set text alignment using a numeric keypad layout for those buttons with a defined address range Syntax: '^JST-<variable text address range>,<new text alignment>'" Variable: • variable text address range = 1; the address range corresponds to the dynamic line number. •... -
Page 19: Sst
Programming The Mio R-3 Send_Commands (Cont.) @SST Sends a string to the master upon start up Syntax: "'@SST-<new text>'" Variables: • new text = 1 - 20 ASCII characters. Default string is STARTUP. Example: SEND_COMMAND Panel,"'@SST-Panel Start'" Sends the string " Panel Start " to the master at time of start up. @SWK Sends a string to the master upon wakeup Syntax:... -
Page 20: Mio Remote Charging Base
Mio Remote Charging Base Mio Remote Charging Base Overview The Mio remotes are complemented with a Mio-RCC charging base (FG147-02). Insert MIO-R3 front Mio-RCC Charging Base FIG. 5 Angle barrel power connector (Bottom View) (Top View) Charging contacts Mio Remote Charging Base (Top and Bottom view) FIG. -
Page 21: Mio-Rcc Specifications
• 1.15 lbs (.52 kg) - Remote Charging Cradle • .15 lbs (.07 kg) - Power Supply • .06 lbs (.027 kg) - Rechargeable Lithium Battery Other AMX Equipment: • Mio R-1 (FG147) • Mio R-2 RF 418 (FG147-418) • Mio R-2 RF 433 (FG147-433) •... - Page 22 © 2016 Harman. All rights reserved. Modero, NetLinx, AMX, AV FOR AN IT WORLD, and HARMAN, and their respective logos are registered trademarks Last Revised: of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective companies.