Table of Contents
Advertisement
If Contact ID Sends Automatic Reporting Codes
Contact ID Sends Automatic Reporting Codes is
Contact ID Sends Automatic Reporting Codes
Contact ID Sends Automatic Reporting Codes
selected, the panel will automatically generate a reporting
code for each event. These identifiers are listed in Appen-
dix A. If the Automatic Contact ID option is not selected,
reporting codes must be programmed. The 2-digit entry
determines the type of alarm. The panel will automati-
cally generate all other information, including the zone
number.
NOTE:
If the Automatic Contact ID option is selected, the
panel will automatically generate all zone and access code
numbers, eliminating the need to program these items.
NOTE:
The zone number for Zone Low Battery and Zone
Fault events will not be identified when Programmed Con-
tact ID is used.
If the Contact ID
ses Automatic Reporting Codes
option is enabled, the panel will operate as follows:
• If an event's reporting code is programmed as [00], the
panel will not attempt to call the central station.
• If the reporting code for an event is programmed as
anything from [01] to [FF], the panel will automatically
generate the zone or access code number. See Appen-
dix A for a list of the codes which will be transmitted.
If the Contact ID
ses Programmed Reporting Codes
option is enabled, the panel will operate as follows:
• If an event's reporting code is programmed as [00] or
[FF], the panel will not attempt to call central station.
• If the reporting code for an event is programmed as
anything from [01] to [FE], the panel will send the pro-
grammed reporting code.
• Account numbers must be four digits.
• If the digit 0 is in the account number substitute the
Hex digit A for the 0.
• All reporting codes must be two digits.
• If the digit 0 is in the reporting code substitute the Hex
digit A for the 0.
• To prevent the panel from reporting an event program
the reporting code for the event as [00] or [FF].
Contact ID Sends Automatic
Reporting Codes. . . . . . . . . . . . . . . . . . . . Section [381], Option [7]
This section requires 2 two-digit entries (1 per phone
number). The 3rd telephone number uses the format pro-
grammed for the 1st telephone number.
Entry
Communication Format
01
20 bps, 1400 HZ handshake
02
20 bps, 2300 HZ handshake
03
CONTACT I.D.
04
SIA FSK
05
Pager
06
Residential Dial
07
10 bps, 1400 Hz handshake
08
10 bps, 2300 Hz handshake
Reporting Codes
• SIA - 0 is valid in account or reporting code (not 00 in a
reporting code)
• ADEMCO Contact ID - 0 is not valid in account or
reporting code (A must be used, 10 in checksum)
• BPS Formats - 0 is not valid in account or reporting
code (A must be used)
• SIA - This format uses 300 Baud FSK as the communi-
cation medium. The account code can be 4 or 6 hexa-
decimal digits in length, all reporting codes must be 2-
digits in length. The SIA format will transmit a 4- (or 6-
digit account code, a 2-digit identifier code and a 2
digit reporting code. The 2-digit identifier is pre-pro-
grammed by the panel.
Telephone Line Monitoring (TLM)
When the TLM Enable
TLM Enable option is selected, the panel will
TLM Enable
TLM Enable
supervise the telephone line and will indicate a Trouble
condition if the telephone line is disconnected.
If the TLM Enable
TLM Enable option is ON, the panel will check the
TLM Enable
TLM Enable
telephone line every 10 seconds. If the telephone line volt-
age is below 3V for the number of checks programmed in
the TLM Trouble Delay
TLM Trouble Delay
TLM Trouble Delay section, the panel will report a
TLM Trouble Delay
TLM Trouble. The default number of checks is 3. Enter a
number from (000) to (255) in the TLM Trouble Delay sec-
tion to change the number of checks before the TLM Trou-
ble is reported. Programming a delay means that a
momentary interruption of the telephone line will not
cause a Trouble condition.
If the TLM Trouble Beeps When Armed
TLM Trouble Beeps When Armed option is enabled,
TLM Trouble Beeps When Armed
TLM Trouble Beeps When Armed
the panel will indicate a TLM Trouble at the keypad while
the system is armed. To activate the bell output in the case
of a TLM Trouble while the system is armed, the TLM
Audible (Bell) When Armed option must be selected.
Audible (Bell) When Armed
Audible (Bell) When Armed
Audible (Bell) When Armed
When the Trouble condition is restored, the panel can
send a TLM Restoral
TLM Restoral reporting code. Any events which
TLM Restoral
TLM Restoral
occur while the telephone line is down will also be com-
municated.
If the LINKS1000 Cellular Communicator, or LINKS2X50
is being used, the panel can be programmed to report a
TLM Trouble reporting code.
TLM Trouble
TLM Trouble
TLM Trouble
[351]-[376] - Communicator Call Directions
For events from each Call Direction group the control
panel can call 2 different phone numbers and use the
LINKS as backup or as a redundant communicator for
one or both numbers. The third phone number can only
be used as a backup or alternate to the first.
Each report falls under one of the following 5 Groups:
1. 1. 1. 1. Partition 1 Alarms & Restorals
2. 2. 2. 2. Partition 1 Openings & Closings
3. 3. 3. 3. Partition 1 Tampers & Restores
4 4 4 4 . System Maintenance Alarms & Restorals
5. 5. 5. 5. System Test Transmissions
Each group can be assigned to the following Call Direc-
Each group can be assigned to the following Call Direc-
Each group can be assigned to the following Call Direc-
Each group can be assigned to the following Call Direc-
tions
tions
tions
tions
1. 1. 1. 1. Option 1
Option 1 - 1st Telephone Number (and 3rd Telephone
Option 1
Option 1
Number if enabled for alternate or backup)
2. 2. 2. 2. Option 2
Option 2
Option 2
Option 2 - 2nd Telephone Number
3. 3. 3. 3. Option 3
Option 3 - 1st Telephone Number via LINKS (and 3rd
Option 3
Option 3
Telephone Number if enabled for alternate or backup)
4. 4. 4. 4. Option 4
Option 4
Option 4
Option 4 - 2nd Telephone Number via LINKS
5. 5. 5. 5. Option 5
Option 5 - Alternate Communicator. This allows the
Option 5
Option 5
panel to have control of what types of events the
LINKS2X50 products will communicate. This Call
Direction is enabled at default.
33
TLM
TLM
TLM
Hide quick links:
Advertisement
Table of Contents
