Miele CS 1327 Operating And Installation Instructions

Miele CS 1327 Operating And Installation Instructions

Stainless steel tepan yaki


Operating and installation instructions
Stainless steel Tepan Yaki
To avoid the risk of accidents or damage to the appliance it is essential
to read these instructions before it is installed and used for the first time.
M.-Nr. 09 054 670



  Summary of Contents for Miele CS 1327

  • Page 1 Operating and installation instructions Stainless steel Tepan Yaki To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr. 09 054 670...
  • Page 2: Table Of Contents

    Contents Warning and Safety instructions................ 3 Caring for the environment ................ 11 Guide to the appliance .................. 12 Tepan Yaki ......................12 Indicators....................... 12 Using for the first time .................. 13 Cleaning the CombiSet for the first time ............... 13 Switching on the CombiSet for the first time ............
  • Page 3: Warning And Safety Instructions

    They contain important notes on installa- tion, safety, use and maintenance. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions. Keep these instructions in a safe place and ensure that new users...
  • Page 4 Warning and Safety instructions Correct application  This Tepan Yaki is intended for domestic use and use in other sim- ilar environments.  The appliance is not intended for outdoor use.  It is intended for domestic use only to cook food and keep it warm.
  • Page 5 Warning and Safety instructions Safety with children  Children under 8 years of age must be kept away from the appli- ance unless they are constantly supervised.  Children 8 years and older may only use the appliance unsuper- vised if they have been shown how to use it in a safe way and can recognise and understand the consequences of incorrect operation.
  • Page 6  Unauthorised installation, maintenance and repairs can cause considerable danger for the user. Installation, maintenance and re- pairs must only be carried out by a Miele authorised technician.  Do not use a damaged appliance. It could be dangerous. Check the appliance for visible signs of damage.
  • Page 7 Miele authorised service technician. Otherwise the guarantee is invalidated.  Miele can only guarantee the safety of the appliance when genu- ine original Miele replacement parts are used. Faulty components must only be replaced by Miele spare parts.
  • Page 8 Warning and Safety instructions Correct use  The appliance gets hot when in use and remains hot for a while after being switched off. There is a danger of burning until the resid- ual heat indicators go out.  Due to the high temperatures radiated, objects left near the appli- ance when it is in use could catch fire.
  • Page 9 Warning and Safety instructions  You could burn yourself on the hot appliance. Protect your hands with heat-resistant pot holders or gloves when working with the hot appliance. Do not let them get wet or damp, as this causes heat to transfer through the material more quickly with the risk of scalding or burning yourself.
  • Page 10 Warning and Safety instructions Cleaning and care  Do not use a steam cleaning appliance to clean this appliance. The steam could reach electrical components and cause a short cir- cuit.
  • Page 11: Caring For The Environment

    Caring for the environment Disposal of the packing mater- Disposal of your old appliance Electrical and electronic appliances of- ten contain valuable materials. They The packaging is designed to protect also contain materials which, if handled the appliance from damage during or disposed of incorrectly, could be po- transportation.
  • Page 12: Guide To The Appliance

    Guide to the appliance Tepan Yaki a Rear cooking zone d Indicators b Front cooking zone e Control for rear cooking zone c Symbols to indicate which cooking f Control for front cooking zone zone the control is for Indicators f In-operation indicator g Temperature indicator light h Residual heat indicator...
  • Page 13: Using For The First Time

    Using for the first time  Please stick the extra data plate for Switching on the CombiSet for the appliance supplied with this doc- the first time umentation in the space provided in The metal components have a protect- the "After sales service, data plate, ive coating which when heated for the guarantee"...
  • Page 14: Settings

    Settings Cooking process Setting range Keeping cooked food warm 1–2 Steaming fruit, e.g. apple slices, peach halves, sliced bananas, 2–4 etc. Gentle stir-frying of vegetables, e.g. leeks, sliced mushrooms, 5–7 green/red peppers, onion rings, etc. Gentle frying of breaded or battered fish 7–9 Rapid frying in succession of meat, fish fried eggs, pancakes, 9–11...
  • Page 15: Operation

    Operation The Tepan plate is divided into two sep- Residual heat indicator arate cooking zones which can be If the appliance is still hot, the residual switched on and regulated independ- heat indicator will light up after it has ently of one another. The entire area been switched off.
  • Page 16: Tips

    Operation Tips Wipe the surface of the Tepan plate before each use with a damp cloth to remove any dust or other residue. – Pre-heat the Tepan plate thoroughly for 8-10 minutes at the power level that you are going to be using for cooking.
  • Page 17: Cleaning And Care

    Cleaning and care  Allow the CombiSet to cool down Danger of burning. before cleaning. Before cleaning the appliance make sure that you have switched it off  The CombiSet and accessories and that it has cooled down. should be cleaned after each use. ...
  • Page 18: Frying Surface

    We recom- a non-scouring sponge and a few mend also using a stainless steel condi- drops of Miele Ceramic and stainless tioning agent to help prevent resoiling steel hob cleaning agent (see "Op- (see "Optional accessories).
  • Page 19: Problem Solving Guide

    Danger of injury. Installation, maintenance and repairs may only be carried out by a suitably qualified and competent person. Repairs and other work by unqualified persons could be dangerous. Miele can- not be held liable for unauthorised work. Do not attempt to open the casing of the CombiSet yourself.
  • Page 20: Optional Accessories

    Miele appliances. Removes heavy soiling, limescale de- These can be ordered online or from posits and aluminium residues Miele (see end of this booklet for con- tact details). Microfibre cloth Removes finger marks and light soiling...
  • Page 21: Safety Instructions For Installation

    Safety instructions for installation Fit the wall units and cooker hood before fitting the CombiSet to avoid dam- aging it.  The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort.
  • Page 22: Safety Distances

    Safety distances Safety distance above the CombiSet A minimum safety distance must be maintained between the CombiSet and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood a min- imum safety distance of at least 760 mm must be maintained, or if any flammable objects (e.g.
  • Page 23 CS 1234 / CS 1234-1 CS 1223 CS 1222 Recommended 50 mm CS 1112 CS 1122 CS 1134 CS 1326 CS 1327 CS 1411 100 mm CS 1012 / CS 1012-1 150 mm CS 1421 CS 1312 Not recommended CS 1322...
  • Page 24 Safety distances Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.g. wood) a minimum safety distance ...
  • Page 25: Installation Notes

    Installation notes Seal between the CombiSet Tiled worktop and the worktop Grout lines  and the hatched area un- derneath the CombiSet frame must be smooth and even. If they are not the Do not use sealant between the CombiSet will not sit flush with the CombiSet and the worktop.
  • Page 26: Building-In Dimensions

    Building-in dimensions a Spring clamps b Front c Casing depth d Casing depth including mains connection box with mains connection cable, L = 2000 mm...
  • Page 27: Building-In Several Combisets

    Building-in several CombiSets Example: 3 CombiSets a Spring clamps b Spacer bars c Gaps between spacer bars and worktop d Cover strips e CombiSet width minus 8 mm f CombiSet width g CombiSet width minus 8 mm h Worktop cut-out...
  • Page 28 Building-in several CombiSets Calculating the worktop cut-out The frames of the CombiSets overlap the worktop at the outside right and left by 8 mm on each side.  Add up the widths of the CombiSets and subtract 16 mm from this figure. Example: 288 mm + 288 mm + 380 mm = 956 mm - 16 mm = 940 mm The CombiSets are 288 mm, 380 mm or 576 mm wide depending on model (see...
  • Page 29: Installation

    Installation Preparing the worktop  Make the worktop cut-out as shown in "Building-in dimensions" or as cal- culated (see Building several CombiSets). Observe the safety dis- tances (see "Safety distances"). Wooden worktops  Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture.
  • Page 30 Installation Natural stone worktops You will need heavy duty double-side tape (not supplied) to secure the spring clamps and spacer bars.  Apply silicone to the side and lower edges of the spring clamps  and the spacer bars .  Then fill gap  between spacer bar ...
  • Page 31 Installation Building in several CombiSets Installation with a downdraft extractor  Push the built-in CombiSet to the side until the holes in the spacer bar Please refer to the separate "Downdraft can be seen. extractor with CombiSet" instruction manual for details about installing a downdraft extractor with a CombiSet appliance.
  • Page 32 Installation Connecting the CombiSet  Connect the CombiSet(s) to the mains.  Check that each CombiSet works. Removing the CombiSet If the CombiSet cannot be accessed from below, you will need a special tool to remove it.  If the CombiSet can be accessed from below, push it out from below.
  • Page 33: Electrical Connection

    Residual current device  Danger of injury. For extra safety, it is advisable to pro- Miele cannot be held liable for unau- tect the CombiSet with a suitable resid- thorised installation, maintenance ual current device (RCD) with a trip and repair work as this can be dan- range of 30 mA.
  • Page 34 If the mains cable needs to be replaced it must be replaced with a special con- Safety fuses nection cable, type H 05 VV-F (PVC-in- sulated), available from Miele.  Completely remove fuses The connection data is quoted on the Automatic circuit breakers data plate.
  • Page 35: After Sales Service, Data Plate, Guarantee

    N.B. A call-out charge will be applied to service visits where the problem could have been resolved as described in these instructions. When contacting your Dealer or Miele, please quote the model and serial number of your appliance. Data plate Space in which to stick the extra data plate supplied with the appliance.
  • Page 36: Product Data Sheets

    Information for domestic electric hobs In acc. with regulation (EU) No. 66/2014 MIELE Model name / identifier CS 1327 Number of cooking zones and/or areas For circular cooking zones: diameter of useful sur- 1. = 190x290 mm face area/cooking zone 2.
  • Page 39 Citywest Business Campus, Dublin 24 Dubai Tel: (01) 461 07 10, Fax: (01) 461 07 97 Tel: +971-4-341 84 44 E-Mail: info@miele.ie, Internet: www.miele.ie Fax: +971-4-341 88 52 Manufacturer: Miele & Cie. KG E-Mail: info@miele.ae Carl-Miele-Straße 29, 33332 Gütersloh, Germany Internet: www.miele.ae...
  • Page 40 CS 1327  en-GB M.-Nr. 09 054 670 / 03...