Operating and installation instructions Stainless steel TepanYaki CS 1327 en - GB To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
Contents Guide to the appliance ..........3 Warning and Safety instructions .
Guide to the appliance Rear cooking zone Front cooking zone Symbols to indicate which cooking zone the controls are for Indicators Control for rear cooking zone Control for front cooking zone Indicators In-operation indicator Temperature indicator light Residual heat indicator...
They contain important notes on installation, safety, use and maintenance. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.
Warning and Safety instructions Correct application This Tepan Yaki is not designed for commercial use. It is intended for use in domestic households and similar working and residential environments. The appliance is not intended for outdoor use. It is intended for domestic use only to cook food and keep it warm.
Warning and Safety instructions Safety with children Children under 8 years of age must be kept away from the appliance unless they are constantly supervised. Children 8 years and older may only use the appliance if they have been shown how to use it in a safe way and understand the hazards involved.
Warning and Safety instructions Technical safety Installation, maintenance and repairs may only be carried out by a Miele-authorised person. Installation, maintenance and repairs by unqualified persons could be dangerous. A damaged appliance can be dangerous. Check the appliance for visible signs of damage. Do not use a damaged appliance.
The manufacturer can only guarantee the safety of the appliance when original Miele replacement parts are used. Faulty components must only be replaced by genuine Miele original spare parts. The appliance is not intended for use with an external timer switch or a remote control system.
Warning and Safety instructions Correct use Oil and fat are potential fire hazards as they can ignite if overheated. Do not leave the appliance unattended when cooking with oil or fat. If oil or fat does catch fire, do not attempt to put out the flames with water.
Warning and Safety instructions The appliance gets hot when in use and remains hot for a while after being switched off. There is a danger of burning until the residual heat indicator goes out. You could burn yourself on the hot appliance. Protect your hands with heat-resistant pot holders or gloves when handling hot pots and pans.
Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The packaging is designed to protect handled or disposed of incorrectly the appliance from damage during could be potentially hazardous to transportation.
Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "service, data plate, guarantee" section of this booklet. Cleaning for the first time ^ Remove any protective foil and sticky labels.
Operation Switching on and off The Tepan plate is divided into two separate cooking zones which can be To switch the Tepan plate on, turn the switched on and regulated control clockwise. To switch off, turn independently of one another. The the control anti-clockwise.
Operation Settings Cooking process Settings Keeping cooked food warm 1 - 2 Steaming fruit, e.g. apple slices, peach halves, 2 - 4 sliced bananas, etc. Gentle stir frying of chopped/sliced vegetables, e.g. 5 - 7 leeks, mushrooms, green/red peppers, onion etc. Gentle frying of breaded or battered fish 7 - 9 Rapid frying in succession of meat, fish...
Operation Tips – Marinating often improves the flavour of food to be cooked. Wipe the surface of the Tepan plate – Pat wet food dry with kitchen paper before each use with a damp cloth before cooking to prevent it spitting. to remove any dust particles or other soiling which may have settled on it –...
Cleaning and care Miele offer a range of branded cleaning To avoid damaging the surface of products. See "Optional accessories". your appliance, do not use: – cleaning agents containing soda, Do not use a steam cleaner to alkalines, ammonia, acids or clean this appliance.
Stainless steel frame / control panel Follow the manufacturer's instructions Clean the frame and the control panel when using a stainless steel cleaning with a few drops of Miele Ceramic and agent. stainless steel hob cleaning agent (see "Optional accessories") and a soft, Frying surface damp cloth.
Check whether the mains fuse has accordance with current local and tripped. If it has, contact a qualified national safety regulations. Repairs electrician or Miele. and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable...
Optional accessories Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances. These can be ordered online at: or from Miele (see back cover for contact details). Ceramic and stainless steel hob cleaner 250 ml...
Safety instructions for installation After installation, ensure that the To avoid the risk of damaging the connection cable cannot come into TepanYaki fit the wall units and contact with the underside of the extractor hood before installing it. appliance. Make sure that there is no mechanical obstruction, such as a The veneer or laminate coatings of drawer, which could damage it.
Safety instructions for installation Safety distance above the TepanYaki A minimum safety distance must be maintained between the Tepan plate and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood, a minimum safety distance of at least 760 mm must be maintained.
CS 1223 CS 1234 / CS 1234-1 CS 1112 50 mm Not recommended CS 1122 CS 1134 CS 1326 CS 1327 CS 1411 100 mm for CS 1012 / CS 1012-1 150 mm for CS 1421 CS 1312 CS 1322...
Safety instructions for installation Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e. g. wood) a minimum safety distance of 50 mm must be maintained between the cut-out and the cladding.
Appliance and building-in dimensions Spring clamps Front Casing depth Casing depth including mains connection box with mains connection cable, L = 1440 mm...
Preparing the worktop ^ Make the worktop cut-out for one or more appliances in accordance with the building-in diagrams. Remember to maintain the minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the TepanYaki.
Installation of several appliances When installing two or more appliances next to each other a spacer bar must be used between each one. See "Fixing the spring clamps and spacer bars". Worktop cut-out Worktop cut-out - two appliances - three appliances To calculate the cut-out width (D) required: Add up the widths of each appliance (e.g.
Installation of several appliances Spring clamps Spacer bars Gaps between spacer bars and worktop Cover strips The illustration shows a worktop cut-out with spring clamps and spacer bars for 3 appliances. An additional spacer bar is required for each additional appliance. The position for securing each additional spacer bar will depend on the width of appliance B (288 mm / 380 mm / 576 mm).
Fixing the spring clamps and spacer bars Wooden worktops ^ Position the spring clamps supplied and spacer bars on the top edge of the cut-out in the positions marked. ^ Secure the spring clamps and spacer bars with the 3.5 x 25 mm screws supplied.
Fixing the spring clamps and spacer bars Granite and marble worktops The screws are not required for granite or marble worktops. ^ Apply silcone to the side edges and the lower edges of spring clamps and spacer bars ^ Then fill gap between the spacer ^ Position and secure the spring bars and the worktop with silicone.
Installing the appliance(s) ^ Feed the connection cable down ^ Starting at the front, position the next through the cut-out. appliance in the worktop cut-out. ^ Starting at the front, position the ^ Connect the appliance(s) to the appliance in the worktop cut-out. mains (see "Electrical connection").
General installation tips Seal between the appliance and the Tiled worktop worktop The sealing strip under the edge of the Grout lines and the hatched area top part of the appliance provides a underneath the surface of the sufficient seal for the worktop. appliance must be smooth and even.
H 05 V V-F be provided for all poles. (pvc insulated), available from Miele. For extra safety it is advisable to protect the appliance with a suitable residual Installation, repairs and other work current device (RCD).
Electrical connection Important The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system, which complies with local and national regulations. It is most important that this basic safety requirement is present and tested regularly and if there is any doubt the electrical wiring in the home should be inspected by a...
Please note that telephone calls may be monitored and recorded to improve our service. When contacting Miele, please quote the model and serial number of your appliance which are given on the data plate. N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions.
Alteration rights reserved/ 5012 M.-Nr. 09 054 670 / 02...