Operating and installation instructions Open barbeque grill CS 1312 CS 1322 en - GB To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. M.-Nr.
Guide to the appliance CS 1312 a Grill rack b Front heating element c Rear heating element d Lava rock container e Drain tap f Symbols to indicate which heating element the control is for g Display Controls for the heating elements: h Front i Rear Display...
CS 1322 a Grill racks b Front heating element c Rear heating element d Lava rock container e Drain tap f Symbols to indicate which heating element the control is for g Display Guide to the appliance Controls for the heating elements: h Front i Rear Display...
Any other use is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation of the appliance. This appliance is not intended for...
Warning and safety instructions Safety with children This appliance is only intended for use by adults who have read these instructions. It is not a toy! To avoid the risk of injury, keep children well away and do not allow them to play with it or use the controls.
Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock). Before connecting the appliance to...
Miele cannot be held liable for damage caused by incorrect installation or connection.
Only close the door if the appliance is switched off. This appliance must not be set up or operated in the open air. Miele cannot be held liable for damage caused by non-compliance with these Warning and safety instructions.
Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children.
Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service, data plate" section of this booklet. Cleaning for the first time ^ Remove protective wrapping the heating elements and also remove any protective foil from the appliance.
Operation Grill chart The times given in the table serve as a guide, based on a pre-heated grill at settings 9 to 12. The grilling time required will depend on the type of food, its texture and thickness as well as personal taste. Food Meat and sausages Sausages...
Food Vegetables Aubergines Jacket potatoes, pre-cooked Vegetarian kebabs Corn on the cob, pre-cooked Peppers, cut into strips Tomato halves Fruit Pineapple slices Apple slices Miscellaneous Toast Tofu Operation Time in minutes 6 - 8 10 - 20 5 - 6 5 - 8 2 - 3 2 - 4...
Operation To prepare the grill The grill can be used with or without the lava rocks. Without the lava rocks the rising steam keeps the food being grilled moist. Grilling with the lava rocks creates a particularly intensive aroma. ^ Check that the drain tap is closed. ^ Remove the rack (or racks, depending on model), lift up the heating elements, and if not being...
Grilling When grilling, keep an eye on the level of water in the trough. If necessary, add more water. When grilling or keeping food warm, do not use grill pans, griddles, saucepans or similar on the open grill, and never cover the rack(s) (e.g.
Safety features Overheating protection A safety cut-out automatically switches the appliance off if the water level drops too low. ^ Add some cold water. As soon as the appliance has cooled down, the heating elements switch back on again and you can continue grilling.
Do not use a steam cleaning appliance to clean this appliance. The steam could reach the electrical components and cause a short circuit. Clean the appliance regularly, preferably after each use. Allow the appliance to cool down to a safe temperature before cleaning.
Cleaning and care Stainless steel The ceramic and stainless steel hob cleaner is suitable for cleaning stainless steel surfaces (see "Optional accessories"). To help prevent resoiling, we recommend a stainless steel conditioner (see "Optional accessories"). Apply sparingly with a soft cloth. Do not use a stainless steel cleaning agent on printed surfaces.
Grill trough Clean the grill trough after each use. ^ After grilling, allow the water in the trough to cool down before draining ^ Place a container large enough to take the contents of the trough under the drain. ^ Open the drain tap under the grill by turning it anti-clockwise a.
Proceed as described in "Overheating protection". – the mains fuse has tripped. If it has, contact a qualified electrician or the Miele Service Department..the food does not begin to brown when the appliance has been pre-heated at setting "12" for 10 minutes.
Miele offers a range of useful accessories designed for your appliance. These can be ordered via the internet at www.miele-shop.com, or from Miele (see back cover for contact details) or from your Miele dealer. Griddle CSGP 1300 Cast-iron griddle to place on top of the CS 1312 grill,...
Optional accessories Cleaning and care products Ceramic and stainless steel hob cleaner 250 ml Removes heavy soiling, limescale deposits and light discolouration Stainless steel conditioning agent 250 ml Removes water marks, flecks and finger prints. Helps keep the appliance looking good for longer. E-Cloth (microfibre cloth) Removes finger marks and light soiling.
Fit the wall units and extractor hood before fitting the barbecue grill to avoid damaging the surface. The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort. Any backmoulds must be of heat-resistant material.
Safety instructions for installation Safety distance above the grill A minimum safety distance must be maintained between the hob and the cooker hood above it. See the cooker hood manufacturer’s operating and installation instructions for details. If the manufacturer’s instructions are not available for the cooker hood, then a minimum safety distance of at least 760 mm must be maintained.
Safety distances to the sides of the grill Ideally the grill should be installed with plenty of space on either side. There may be a wall at the rear and a tall unit or wall at one side. On the other side, however, no unit or divider should stand higher than the built-in appliance (see illustrations).
Safety instructions for installation Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e. g. wood) a minimum safety distance e of 50 mm must be maintained between the cut-out and the cladding.
^ Make the worktop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the appliance(s).
Installation of several appliances When installing two or more appliances next to each other a spacer bar b must be used between each one. See "Fixing the spring clamps and spacer bars". Worktop cut-out - two appliances To calculate the cut-out width (D) required: Add up the widths of each appliance (e.g.
Installation of several appliances a Spring clamps b Spacer bars c Gap between spacer bar and worktop d Sealing strip The illustration shows a worktop cut-out with spring clamps a and spacer bars b for 3 appliances. An additional spacer bar is required for each additional appliance. The position for securing each additional spacer bar will depend on the width of appliance B (288 mm / 380 mm / 576 mm).
Fixing the spring clamps and spacer bars Wooden worktops ^ Position the spring clamps supplied a and spacer bars b on the top edge of the cut-out in the positions marked. ^ Secure the spring clamps and spacer bars with the 3.5 x 25 mm screws supplied.
Fixing the spring clamps and spacer bars Granite and marble worktops The screws are not required for granite or marble worktops. ^ Position and secure the spring clamps a and spacer bars b using strong, double-sided adhesive tape ^ Apply silcone to the side edges and the lower edges of the spring clamps a and spacer bars b.
Installing the appliance(s) ^ Feed the connection cable down through the cut-out. ^ Starting at the front, position the appliance in the worktop cut-out. ^ Using both hands, press down evenly on the sides of the appliance until it clicks into position. When doing this make sure that the seal under the appliance sits flush with the worktop on all sides.
Do not use any sealant unless expressly instructed to do so. The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop. Do not use sealant between the frame of the top part of the appliance and the worktop.
If the connection cable is damaged, it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V-F (pvc insulated), available from Miele. Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.
Important The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system, which complies with local and national regulations. It is most important that this basic safety requirement is present and tested regularly and if there is any doubt the electrical wiring in the home should be inspected by a...
Please note that telephone calls may be monitored and recorded to improve our service. When contacting Miele, please quote the model and serial number of your appliance which are given on the data plate. N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions.