WARNING- When using your appliance follow basic precautions, including the following: Read all instructions before installation or use to prevent injury and appliance damage. This appliance conforms to all uniform safety codes and regulations. The manufacturer cannot be held responsible for damage or injury caused by improper use of this appliance.
IMPORTANT SAFETY INSTRUCTIONS Technical Safety Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. Before installing the appliance, check for externally visible damage.
Safety The appliance is hot during use and remains so for some time after being switched off. Be careful not to touch the appliance if it may still be hot. Protect your hands with oven mitts or potholders when using the appliance.
IMPORTANT SAFETY INSTRUCTIONS To prevent burns and breathing difficulty, allow the appliance to cool before cleaning. Some cleaners may produce toxic fumes if applied to a hot surface. When wiping spills on a hot appliance with a wet sponge or cloth, be careful to avoid steam burns.
a Grates b Heating element, front c Heating element, rear d Lava rock container e Drain valve f Cooking area indicators g Display Description of the unit Control knobs: h front i rear Display j On/Off indicator...
Before using for the first time Clean the appliance ^ Clean the water trough and the grill with a mild solution of warm water and liquid dish liquid, then dry with a soft cloth (see "Cleaning and care"). ^ Wipe the other surfaces down with a damp cloth and dry.
Prepare the appliance You can use the electric barbecue with or without the lava rocks. Without the lava rocks: food will stay more moist, from the rising steam. With the lava rocks: the food will have a more pronounced grilled aroma and flavor.
Grilling While grilling, watch the level of water in the trough. If necessary, add more water. Do not use aluminum dishes, pans, pots or foil on the grill. Never cover the grill grate with aluminum foil. Aluminum will cause overheating and may damage the grill grate.
Safety Feature Overheat protection If there is not enough water in the water trough, the overheat protection automatically switches the appliance off. ^ Pour in cold water. Once the appliance has cooled down and the heating element switches back on, you can continue grilling as normal. Safety cut-out feature The safety cut-off ensures that the heating element will only work if it is...
Under no circumstances use a steam cleaner to clean this appliance. Pressurized steam could cause permanent damage to the surface and to components for which the manufacturer cannot accept responsibility. Never use strong cleaners e.g. oven sprays, stain or rust removers. Scouring pads and abrasive cleaning agents should only be used on the heating element.
Cleaning and care Lava rocks Clean the lava rocks on a regular basis. To do so, put the rocks in a container with mild solution of warm water and liquid dish soap. Let them soak briefly, stirring occasionally. Drain water and rinse rocks.
10 minutes at level 12? The knob is not exactly set to level 12, and the appliance is not opretaing at full power. Frequently asked questions Solution See "Overheat protection" Contact a qualified electrician or Miele Technical Service for assistance. Correct the setting.
Technical Service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance.
Miele offers a variety of additional accessories for its appliances. All accessories can be ordered from Miele. Griddle CSGP 1400 Cast grill plate, with one smooth side and one ridged side, for CS 1322 Wire rack for Griddle Plate CSGP1400...
However, under certain conditions it may be possible for installation in these applications. Please contact the Miele Technical Service Department with specific requirements. The grill must not be installed directly next to the CS 1421 (Salamander).
30" (760 mm) must be maintained. If there is more than one appliance beneath a hood (e.g. wok burner and electric grill), and they have different minimum safety distances always observe the greater distance.
SAFETY INSTRUCTIONS FOR INSTALLATION Safety distances to the sides of the appliance The appliance should only be installed as shown in the illustrations while maintaining the required safety distances shown. Do not install the appliance between two tall cabinets, this is a fire hazard. A distance of at least 2"...
Installation Safety distance when installing the appliance near a wall with trim or a back splash A minimum distance of 2" (50 mm) between the trim or back splash and the countertop cut-out if required. This distance is only necessary if these items are made of combustible materials e.g.
Cut out ^ Make the worktop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the appliance(s).
Installation Installation of multiple appliances When installing more than one combiset appliance, a support bar b must be installed between the appliances. Countertop cut-out two appliances For the installation of two appliances the width of the countertop cut-out D is the sum of A and C.
Sample calculations for a countertop cut-out for three appliances appliance width minus " (8 mm) 11" (280 mm) 11" (280 mm) 11" (280 mm) " (372 mm) " (372 mm) " (372 mm) /8" (568 mm) " (568 mm) " (568 mm) appliance width appliance width...
Installation 2 " 2 " " 3 / 1 6 ( 5 0 m ( 5 0 m 1 " - 1 0 m m ( 2 5 - 3 a Spring clips b Support bars c Space between support bar and countertop An additional support bar is required for each additional appliance.
Attach the spring clips and support bars Wood or solid surface countertops 1 " - 1 ( 2 5 - 3 ^ Place the supplied spring clips a and the support bars b at the marked positions as shown above, by laying them on the upper edge of the cut-out and then securing them with the...
Installation ^ Coat the edges of the spring clips a, ^ and the space d between the strips b and the countertop with silicone (supplied).
Installing the appliance ^ Feed the power cord down through the cut-out. ^ Then place the front side of the appliance in the countertop cut-out. ^ Then with a hand on each side of the appliance press down evenly on the edges until it clicks into position.
Installation Sealing The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. If the appliance is sealed into position, the countertop or appliance could be damaged if it needs to be removed for maintenance or service.
CAUTION: Before installation or servicing, disconnect the power supply by either removing the fuse, shutting off the main power supply or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards.
Help protect our environment Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of an old appliance Old appliances contain materials that can be recycled.
Alteration rights reserved / 4608 M.-Nr. 07 374 400 / 00 For the most updated manual see the Miele web site.