Page 1
Important Safety Instructions Specifications General Description Features Software Connecting the Mixer Mixer Controls FlexFX Internal Audio Effects USB Drivers The MP26 Control Panel Dimensions Faders Sound System Interconnection How-to Properly Set Mixer Levels 27 Declaration of Conformity Factory Authorized Service Warranty 20445...
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications not expressly approved by Rane Corporation could void the user's authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003.
• Consulter un revendeur ou un technicien radio / TV expérimenté. ATTENTION: Les changements ou modifications non expressément approuvés par Rane Corporation peuvent annuler l'autorité de l'utilisateur à manipuler cet équipement et rendre ainsi nulles toutes les conditions de garantie.
• One with a line-level input option. • The MP26 MIDI device exposes the MP26 front panel as a MIDI controller, allowing control of audio application parameters WEAR PARTS using the mixer’s control surface.
Page 6
MP26 CLUB MIXER Two Mic Inputs Four Program buses each include • Mic 1 allows connection to either front or rear jack. • Selection of a Phono / CD Input, USB playback • Mic 2 allows switchable Mic or Line level Input.
Page 7
FLEXFX ON ECHO ROBOT REVERB FLEXFX ON Most DJ and DAW software are compatible with the included ASIO and Core Audio drivers. The MP26 includes a low-latency, USB 2.0, BEAT BEAT BEAT BEAT high-speed, 10-input, 12-output audio interface. The MP26 front panel controls are MIDI-mappable in supporting software.
If the Main output feeds a mono PA system, engage the Mono Phono/Line Inputs (P1-P4) switch on the rear of the MP26. If the Main output is able to The MP26 has four stereo Phono/Line inputs ( clip the input to the PA system when the front panel...
2. Select the record source for USB record channel 6 using the MP26 driver control panel on your computer. Connect your computer to the USB port on the MP26 to send MIDI up to twenty-two channels of audio to/from your favorite multi-...
A gooseneck mic is not recommended as it could damage • select assigns the channel to the headphones (pre-fader). the jack and not be covered under Rane’s Warranty. • Channel meter displays mono signal level with peak-hold. • allows selection of a Mic- or Line-level input via the Mic 2 •...
Page 11
MP26 driver control panel. with peak-hold. FlexFX The Main Mix feeds these outputs: • Main Outs The FlexFX architecture in the MP26 is more powerful than • Front panel controls manage the relative Balance Level typical effect insert solutions. The architecture includes the (left/right) and overall levels respectively.
Page 12
MP26 CLUB MIXER The order of processing in the MP26’s FlexFX architecture is: 4 The button engages or bypasses the USB effects USB Loop 1 Independent FlexFX assign for PGM 1-4 and Mic 1-2, or as- insert. The USB insert uses USB record-5 and playback-5 to sign all sources simultaneously with the Main FlexFX button.
The mixer can synchronize its internal effects to a MIDI Beat the last effect is displayed. Clock. Tell the MP26 to track a MIDI Beat Clock by holding The effect time is normally a product of the BPM and the button while pressing the encoder.
32-bit Windows: RaneAsioMP26x86Setup.exe b. 64-bit Windows: RaneAsioMP26x64Setup.exe c. If you install from the CD that came with your MP26, launch the file and it automatically Rane MP26 Setup.bat chooses the right installer.
MIDI In channel number. Checking “Receive plications running) may adversely affect the computer’s ability MIDI Beat Clock” allows the MP26 to track the BPM of a soft- to stream audio reliably. If pops and clicks are heard in the ware application generating MIDI Beat Clock.
Page 16
CLUB MIXER MIDI Out Controls MIDI In Controls All MP26 front panel controls with the exception of the Main The mixer parameters controlled via the MP26 driver control Balance, Main Level, and Zone Level send MIDI output mes- panel are also available for control via MIDI Input. All MIDI sages when changed.
MP26 1.3" (3.3 cm) CLUB MIXER 2.9" (7.4 cm) Dimensions Side Dimensions 2.45" (6.2 cm) 8.75" (22 cm) .7" (1.8 3.7" (9.4 cm) Stereo USB Playback Inputs and Record Outputs 4.4" (11 cm) USB playback Inputs USB 1 USB 2...
Page 18
There are no electrical contacts to clean! 7. Add a drop of silicone lubricant (or quick spray from aerosol) The crossfader in the MP26 is designed with materials highly resistant to corrosion and most chemicals. While the crossfader to the center of each rail.
—Grounding and EMC practices — Shields of connectors in audio equipment containing active circuitry.” Rane’s policy is to accommodate rather than dic- tate. However, this document contains suggestions for external wiring changes that should ideally only be implemented by trained technical personnel. Safety...
Ground Loops Almost all cases of noise can be traced directly to improperly, thus creating balanced equipment that is ground loops, grounding or lack thereof. It is important not immune to the cabling’s noise currents. This is one to understand the mechanism that causes grounding reason for the bad reputation sometimes given to bal- noise in order to effectively eliminate it.
Page 21
Well, some does, and since 1993, A balanced line requires three separate conduc- more of it does. That’s when Rane started manufac- tors, two of which are signal (+ and –) and one shield turing some of its products with balanced inputs and (see Figure 1a).
Page 22
Another way to create the necessary isolation is to RF issues exist, though the increasing use of digital and use a direct box. Originally named for its use to convert wireless technology greatly increases the possibility of the high impedance, high level output of an electric future RF problems.
Page 23
Convention of Audio Engineering Society in San Fran- ground using a star washer for a reliable contact. cisco, CA, Nov. 1994. (Rane always provides this chassis point as an exter- 2. Grounding, Shielding, and Interconnections in Analog nal screw with a toothed washer.) Any device with &...
Page 27
Once you master the fundamental principles you'll know how software are adjusted properly (i.e., no red), you’re ready to adjust to get the best possible audio quality from your Rane DJ mixer. the level controls on your mixer. To ensure proper level setting, Rane DJ mixers are designed with a professional audio metering syste much like you’d find in a...
Page 28
LEARN SOMETHING? MORE ARTICLES LIKE THIS ARE IN ping or distorting audio, not that you can clip or distort a Rane THE KNOWLEDGE BASE AND BLOG AT DJ.RANE.COM.
EMC directive in the event that the equipment is modified without writ- ten consent of the manufacturer. This declaration of conformity is issued under the sole responsibility of Rane Corporation. Type of Equipment:...
Rane Factory in the original packaging or a replacement supplied by Rane, with all transportation costs and full insurance paid each way by the purchaser or owner.
Page 31
New Product Registration. Fill out the warranty completely, being sure to include the model and serial number of the unit since this is how warranties are tracked. If your Rane product was purchased in the U.S.A., mail the completed card or register online with to Rane Corporation within 10 days from the date of purchase.