Truma Manufacturer's Warranty; Installation Instructions; Intended Use; Approval - Truma Trumatic E 2400 E Operating And Installation Instructions

Truma Manufacturer's Warranty

1. Warranty claims
The Manufacturer hereby warrants for all defects of the unit
caused by material or production faults. In addition, the seller
continues to be subject to any statutory warranty claims.
No warranty claim shall be applicable under the following
circumstances:
– Consumable parts which are subject to wear and tear
– Use of parts other than original Truma components in any
of the units
– In gas pressure regulation systems: damage caused by for-
eign substances in the gas (e.g. oils, plasticisers)
– Failure to observe Truma's installation or operating
instructions
– Improper handling
– Improper transport packing
2. Scope of warranty
The warranty covers all defects under clause 1 that occur
within 24 months upon concluding the purchase agreement
between the seller and the end customer. The Manufacturer
undertakes to remedy such defects through subsequent fulfil-
ment, i.e. at its discretion either by repairing or replacing the
defective item. If the Manufacturer remedies a defect under
its warranty commitment, the term of the Warranty shall not
recommence anew with regard to the repaired or replaced
parts; rather, the original warranty period shall continue to be
applicable. No further-reaching claims shall be permitted, es-
pecially damage claims presented by purchasers or third par-
ties. This provision shall not affect the validity of the German
Product Liability Act (Produkthaftungsgesetz).
The Manufacturer shall bear the cost of employing the Truma
Customer Service for the removal of warranty defects – in
particular, transportation, travelling, job and material costs –
provided that the Customer Service conducts its work within
Germany. This Warranty does not cover Customer Service
work outside Germany.
Additional costs arising from complicated removal or installa-
tion jobs on the unit (e.g. dismantling of furnishings or parts
of the vehicle body) are not covered by the Warranty.
3. Making a claim under the warranty
The Manufacturer's address is:
Truma Gerätetechnik GmbH & Co. KG
Wernher-von-Braun-Straße 12
85640 Putzbrunn, Germany
Should problems occur, please contact the Truma Service
Centre or one of our authorised service partners (see Truma
Service Booklet or www.truma.com). Please describe your
claim in detail and state the serial number of the unit and the
date of purchase.
To help the Manufacturer determine whether your claim is
covered by the Warranty, the end user must take or send the
unit to the Manufacturer or service partner at their own risk.
In the event of damage to the heat exchanger, the gas pres-
sure regulator, too, must be returned along with the unit.
Air conditioning systems:
To avoid transport damage, the unit must be sent either to
the Truma Service Centre in Germany or to the relevant au-
thorised service partner; this must only be done upon prior
arrangement. Otherwise the sender shall bear the risk for any
transport damage that may occur.
If a unit is sent to the manufacturing facility, make sure it
is shipped as a freight item. If the claim is covered by the
Warranty, transport / shipping and the cost of return shall be
borne by the manufacturing facility. If the claim is not covered
by the Warranty, the Manufacturer shall notify the customer
to this effect, specifying the cost of repairs not borne by the
Manufacturer; shipping costs, too, shall be borne by the cus-
tomer in such a case.

Installation instructions

The unit must only be installed and repaired by an
expert. Read the installation instructions carefully before
commencing the work, and then comply with them!
Disregarding safety instructions or erroneous
installation can put people in danger and cause
damage to property.

Intended use

This device was designed for installing in vehicles (motor
homes, cars and commercial vehicles). Installation in boats is
not permitted. Other applications are possible subject to prior
consultation with Truma.
Installation inside buses (vehicle classes M2 and M3) is not
permitted.
Vehicles EX/II and EX/III
Combustion heaters for gaseous fuel are not permitted.

Approval

Declaration of conformity
The device complies with the requirements of the following
EC directives:
– Gas Appliances Directive 90/396/EEC
– Heating Appliance Directive 2001/56/EC, 2004/78/EC,
2006/119/EC
Type approval number e1 00 0144
– EMC directive 2004/108/EC.
– Radio interference suppression in vehicles 2004/104/EC,
2005/83/EC, 2006/28/EC
Type approval number e1 03 2605
– End-of-life vehicle directive 2000/53/EC
The CE product identification number for EU countries is:
CE-0085AO0008
The heater is approved for installation in motor vehicles for
transporting passengers (motor caravans in vehicle class M1)
with no more than 8 seats excluding the driver's seat, for trail-
ers (caravans in vehicle class O) and for commercial vehicles
(vehicle class N).
The year when the equipment was first taken into oper-
ation must be indicated with a cross on the type plate.
19