Unit Position - Connection Diagram - Intec MGC2-16 User Manual

PolyGard Multi-Point Controller
®
User Manual - MGC2-16
4.2 Unit position – Connection diagram
Green/Ye
Green/Ye
(see ill. 1)
1 2
X1
Fault Fault
1 2 3 4 5 6 7 8 9 101112
(see ill. 4) Sensor
Inputs
(see ill. 2)
1 2
X1
EP-02-2
(see ill. 4)
1 2 3 4 5 6 7 8 9 101112
Sensor
Inputs
(see ill. 3)
Terminal
block "X1"
Circuit breaker
120 VAC Input Power Supply
AC hot
AC neutral
Earth ground
H N G
Terminal block
Polygard® is a registered trademark of MSR
Customer Services (858) 578-7887 & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
G
Gray X
Gray H
120 VAC
Blue N
Input Power
G
(see ill. 2)
Binary - Relay Outputs Binary - Relay Outputs
R01 R02 R03 R04 R05 R06 R07
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6
1 2
X2 X1
EP-02-1
Alarm Alarm
INTEC Controls
0 5 . 0 7 . 1 0 1 0 : 2 8 a m
X10 X11 X10
1 2 3 4 5 6 7 8 9 101112 1 2 3 4 5 6 7 8 9 101112
Digital Analog Sensor
Inputs Outputs Inputs
Optional:
Modbus Interface
(see ill. 5) (see ill. 6)
(see ill. 8)
Binary - Relay Outputs Binary - Relay Outputs
R11 R12 R13 R14 R15 R16 R17
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6
1 2
X2 X1
EP-02-3
X10 X11 X10
1 2 3 4 5 6 7 8 9 101112 1 2 3 4 5 6 7 8 9 101112
Sensor
Analog
Outputs
Inputs
(see ill. 6) (see ill. 4)
1 24 VDC
2 Output
1F1
Horn
Power Unit
Top Bottom
120 VAC (90...230 VAC), 50/60 Hz
• "Min wire size 16 AWG (1.5 mm
• Resettable breaker, max 10 A,
rated current approx. 2 A
Fax (858) 578-4633 & (888) FX INTEC
(see ill. 2)
(see ill. 3)
R08 R09 R10
7 8 9 10 11 12 13 14 15
X2
DIN Rail
X11
1 2 3 4 5 6 7 8 9 101112
(see ill. 4) Analog (see ill. 6)
Outputs
(see ill. 2)
R18 R19 R20
7 8 9 10 11 12 13 14 15
X2
DIN Rail
X11
1 2 3 4 5 6 7 8 9 101112
Analog
Outputs
(see ill. 6)
)"
2
ill. 1
www.inteccontrols.com
Page 25
1 2 3 4 5 6 7 8
X2
C5 Comm.
Coupler
Optional:
BACnet
X1
1 2 3 4
(+)(-)(A)(B)
(see ill. 7)
Specification subject to change without notice.
Printed in USA 131119
MGC2-16