Toyota 2007 Land Cruiser Owner's Manual

page of 373

/ 373
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Download this manual

Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and

quality construction of each vehicle we build.

This Owner's Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants

follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. For

important information about this manual and your Toyota, read the following pages carefully.

When it comes to service, remember that your Toyota dealer knows your vehicle very well and is interested in your complete

satisfaction. Your Toyota dealer will provide quality maintenance and any other assistance you may require.

If there is not a Toyota dealer near you, please call the following number:

U.S. OWNERS

When traveling in the U.S. mainland or Canada:

Toyota Customer Experience Center

Hawaii:

Servco Automotive Customer Services

Please leave this Owner's Manual in this vehicle at the time of resale. The next owner will need this information also.

All information and specifications in this manual are current at the time of printing. However, because of Toyota's policy of

continual product improvement, we reserve the right to make changes at any time without notice.

Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may

find some explanations for equipment not installed on your vehicle.

Please access our websites for further information.

The U.S. mainland

www.toyota.com

Hawaii

www.toyotahawaii.com



2006 TOYOTA MOTOR CORPORATION

Motor Corporation.

Foreword

Toll−free:1−800−331−4331

Toll−free:1−888−272−5515

Table of Contents

Chapters

Table of Contents

Summary of Contents for Toyota 2007 Land Cruiser

Page 1 Please access our websites for further information. The U.S. mainland www.toyota.com Hawaii www.toyotahawaii.com  2006 TOYOTA MOTOR CORPORATION All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of Toyota Motor Corporation.
Page 2: Important Information About This Manual
Important information about this manual Safety and vehicle damage warnings Safety symbol Throughout this manual, you will see safety and vehicle dam- age warnings. You must follow these warnings carefully to avoid possible injury or damage. The types of warnings, what they look like, and how they are used in this manual are explained as follows: CAUTION This is a warning against anything which may...
Page 3: Occupant Restraint Systems
None of these systems, either indi- Toyota encourages you and your family to take the time vidually or together, can ensure that there is no injury to read Section 1−3 of this Owner’s Manual carefully.
Page 4: Event Data Recorder
Toyota recommends you to read the provisions in Sec- D Engine speed tion 1−3 carefully and refer to them as needed during your time of ownership of this vehicle.
Page 5 D SRS airbag deployment data Toyota will not disclose the data recorded in an EDR to a third party except when: D SRS airbag system diagnostic data D An agreement from the vehicle’s owner (or the leas- If your vehicle is equipped with a vehicle stability con-...
Page 6 New vehicle warranty Important health and safety information about your Toyota Your new vehicle is covered by the following Toyota limited warranties: D New vehicle warranty CAUTION D Emission control systems warranty D Others WARNING: Engine exhaust, some of its constitu- For further information, please refer to the “Owner ’s...
Page 7 TEMS, SRS airbag system and seat belt pretensioner system, This vehicle should not be modified with non−genuine be sure to check with your Toyota dealer for precaution- Toyota products. Modification with non−genuine Toyota ary measures or special instructions regarding installa- products could affect its performance, safety or durabili- tion.
Page 8 Owner’s Manual. For details about tire infla- service shop or by your Toyota dealer before you dis- tion pressure and load limits, see pages 330 and pose of your vehicle.
Page 9 Leak detection pump On−pavement and off−road driving tips This pump performs fuel evaporation leakage check. This check is done approximately five hours after the This vehicle belongs to the utility vehicle class. Utility engine is turned off. So you may hear sound coming vehicles have a significantly higher rollover rate than from underneath the luggage compartment for several other types of vehicles.
Page 11 U −8 Quick index D If a service reminder indicator or warning buzzer comes on ..D If your vehicle will not start ........D If your engine stalls while driving .
Page 12 The Toyota authorized Repair Manual is packed with literally everything you need to know to perform your own maintenance in virtually every area of your new vehicle.
Page 13 The repair manual outlines exactly what main- The repair manual for LAND CRUISER may be tenance is required and clearly explains how to do the purchased from any Toyota dealer or the Mate- work yourself step−by−step. rial Distribution Center. To purchase the repair...
Page 14: Operation Of Instruments And
SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview ........Instrument cluster overview .
Page 15: Instrument Panel Overview
Instrument panel overview "View A 1. Side vents 2. Side defroster outlets 3. Instrument cluster 4. Center vents 5. Electric moon roof switches and/or personal lights 6. Tire pressure warning select switch (in the glove box) 7. Glove box 8. Power door lock switches 9.
Page 16 "View B (Vehicles with navigation system) 1. Headlight, turn signal and front fog light switches 2. Cruise control switch 3. Ignition switch 4. Wiper and washer switches 5. Emergency flasher switch 6. Navigation system including air condi- tioning controls (See separate “Navigation System Owner’s Manual”.) 7.
Page 17 "View B (Vehicles without navigation system) 1. Headlight, turn signal and front fog light switches 2. Cruise control switch 3. Ignition switch 4. Wiper and washer switches 5. Emergency flasher switch 6. Clock, outside temperature and trip in- formation display 7.
Page 18 "Lower part of center cluster panel 1. Ashtray 2. Cigarette lighter 3. Power outlet...
Page 19: Instrument Cluster Overview
Instrument cluster overview 11C501b 1. Voltmeter 4. Tachometer 8. Odometer and two trip meters 2. Speedometer 5. Height control indicator light 9. Trip meter reset knob 3. Service reminder indicators and 6. Engine oil pressure gauge 10. Fuel gauge indicator lights 7.
Page 20 Indicator symbols on the instrument panel ∗ 1 ∗ 1 Brake system warning light Tire pressure warning light ∗ 1 ∗ 1 Driver’s seat belt reminder light Unengaged “Park” warning light Automatic transmission fluid temperature warning ∗ 1 Charging system warning light ∗...
Page 21: 1 : For Details, See "Service Reminder Indicators And Warning
Automatic transmission indicator lights Vehicle stability control system off indicator ∗ 1 light Vehicle stability control system and active ∗ 1 traction control system warning light Active traction control system indicator light Slip indicator light ∗ 3 Roll sensing of curtain shield airbags off indicator light ∗...
Page 22: Table Of Contents
SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys ............Engine immobilizer system .
Page 23: Keys
When using a key containing a trans- 1. Master keys (black)—These keys work ponder chip, observe the following in every lock. Your Toyota dealer will precautions: need one of them to make a new key with a built−in transponder chip.
Page 24 z Do not use the key with electromag- netic materials. z When starting the engine, do not z Do not bend the key grip. use the key with other transponder z Do not cover the key grip with any keys around (including keys of oth- material that cuts off electromagnet- er vehicles) and do not press other ic waves.
Page 25: Engine Immobilizer System
Toyota dealer. need additional keys, duplicates can be the electronic code in the chip corre- made by a Toyota dealer using the key The indicator light stays on except sponds to the registered ID code for number.
Page 26: Wireless Remote Control
The This device complies with Part 15 of the indicator light will go off. FCC Rules. Operation is subject to the For your Toyota dealer to make a new key following two conditions: with a built−in transponder chip,...
Page 27 The wireless remote control key is an If you lose your wireless remote control electronic component. Observe the follow- key, contact your Toyota dealer as soon ing instructions in order not to cause dam- as possible to avoid the possibility of age and trouble to the key.
Page 28 NOTE: *The 2−step unlocking function can vehicle. be changed. **The turn signal lights can be set not to flash. Ask your Toyota deal- er for details.
Page 29 The alarm will last for 1 minute. To stop NOTICE: Connect the equipment into an outlet the alarm midway, push the “PANIC”, This equipment has been tested and on a circuit different from that to “LOCK” or “UNLOCK” switch, or unlock found to comply with the limits for a which the receiver is connected.
Page 30 1. Remove the screw, and then the cover. 2. Remove module from z Replace only with same or frame. equivalent type recommended by a Toyota dealer. z Dispose of used battery according to the local laws. Replace the battery by following these procedures:...
Page 31: Side Doors
After replacing the battery, check that the neously.* key operates properly. If the key still does NOTE: *The 2−step unlocking function can not operate properly, contact your Toyota be changed. Ask your Toyota dealer for dealer. details.
Page 32 LOCKING UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To lock: Push the switch down on the front side. To unlock: Push the switch down on the l12093a rear side. All the side doors and back door lock or unlock simultaneously.
Page 33 —Automatic door locking and unlocking functions AUTOMATIC DOOR LOCKING CAUTION You can select the following functions: Locking linked with the shift position Before driving, be sure that the doors closed locked, especially All doors are automatically locked when when small children are in the ve- the selector lever is moved out of “P”...
Page 34 You can set or cancel the automatic To select the locking linked with the AUTOMATIC DOOR UNLOCKING door locking functions: vehicle speed: You can select the following functions: Be sure to apply the parking brake when 1. Close all doors and turn the ignition Unlocking linked with the shift posi- performing the following operations.
Page 35: Power Windows
Power windows You can set or cancel the automatic To select the unlocking linked with the unlocking functions: ignition switch: Be sure to apply the parking brake when 1. Close all doors and turn the ignition performing the following operations. switch to the “ON”...
Page 36 Window lock switch 12C011a l12088a 12C007b Automatic operation: Push the switch OPERATING THE PASSENGERS’ WIN- Automatic operation: Push the switch completely down or pull it completely up, DOWS completely down or pull it completely up, and then release it. The window will fully and then release it.
Page 37 CAUTION Never leave anyone (particularly a small child) alone in your vehicle, To avoid serious personal injury, you especially with the ignition key still must do the following. inserted. Otherwise, could power window Before you close the power win- switches and get trapped in a win- dows, always make sure there is dow.
Page 38: Power Quarter Windows
Power quarter windows Back door CAUTION To avoid serious personal injury, you must do the following. Before you close the power quarter windows, always make sure there is nobody around the power quarter windows. You must also make sure the hands and other parts of the bodies of all occupants are kept completely inside...
Page 39 Pull the handle toward you and pull LOCKING AND UNLOCKING FROM IN- Push the handle and push down the down the lower side of the back door. SIDE lower side of the back door. When closing the back door, make sure To lock: Push the knob.
Page 40 CAUTION CAUTION Keep the back door closed while Before driving, be sure that the back driving. This not only keeps the door is closed and locked, especially luggage from being thrown out but when small children are in the ve- also prevents exhaust gases from hicle.
Page 41: Hood
Hood Theft deterrent system To open the hood: 2. In front of the vehicle, pull up the To deter vehicle theft, the system is auxiliary catch lever and lift designed to sound an alarm if any of 1. Pull the hood lock release lever. The hood.
Page 42 The system will automatically be set after If any of the side door or back door is 30 seconds. When the system is set, the unlocked without the key or wireless re- indicator light will start flashing again. mote control key and the key is not in the ignition switch, all the side doors and 4.
Page 43: Fuel Tank Cap
CAUTION reconnected. If the system does not work properly, Do not smoke, cause sparks or al- have it checked by your Toyota dealer. low open flames when refueling. The fumes are flammable. When opening the cap, do not re- move the cap quickly. In hot weath-...
Page 44: Electric Moon Roof
CAUTION Make sure the cap is installed se- curely to prevent fuel spillage in the event of an accident. Use only a genuine Toyota fuel tank 12C006b cap for replacement. It is designed to regulate fuel tank pressure. Sliding operation 2.
Page 45 If the moon roof can- rear side. switch. not be operated properly, have it checked by your Toyota dealer. The roof will open and stop partway 30 Jam protection function (closing opera- mm (1.2 in.) from the fully opened posi- tion only): If something gets caught be- tion.
Page 46 CAUTION Never leave anyone (particularly a small child) alone in your vehicle, To avoid serious personal injury, you especially with the ignition key still must do the following. inserted. Otherwise, could use the moon roof switches While the vehicle is moving, always and get trapped in the roof open- keep the heads, hands and other ing.
Page 48 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Occupant restraint systems Seats ............Front seats .
Page 49: Seats
Front seats— —Front seat precautions Seats While the vehicle is being driven, all ve- Driver seat Slightly recline the back of hicle occupants should have the seatback seat. Although vehicle designs vary, upright, sit well back in the seat and prop- CAUTION many drivers can achieve the 250 erly wear the seat belts provided.
Page 50 —Seat adjustment precautions Front passenger seat Front seats (with SRS side airbags) CAUTION CAUTION CAUTION Do not adjust the seat while the vehicle is moving as the seat may The SRS front passenger airbag The SRS side airbags are installed in unexpectedly move and cause the also deploys...
Page 51 —Adjusting front seats 1. SEAT POSITION AND SEAT CUSHION CAUTION ANGLE ADJUSTING SWITCH Move the control switch in the desired Avoid reclining seatback direction. more than needed. The seat belts pro- Releasing the switch will stop the seat at vide maximum protection in a frontal that position.
Page 52: Armrest
Rear seats— —Rear seat precautions Armrest Tumbling the seats will enlarge the lug- CAUTION gage compartment. See “Cargo and lug- gage” on page 257 for precautions when Do not adjust the seat while the loading luggage. vehicle is moving. Be careful that the seat does not hit a passenger or luggage.
Page 53 —Moving second seat —Adjusting second seats third seat entry SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lever toward you. Then lean back to the desired angle and release the lever. CAUTION Avoid reclining the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the second seat passengers are sitting...
Page 54 —Tumbling second seat CAUTION After returning the seat, make sure the seat is securely locked by push- ing forward and rearward on the top of the seatback and by trying to pull I13378b I13340a up the edge of the bottom cushion. BEFORE TUMBLING SECOND SEAT 2.
Page 55 TUMBLING SECOND SEAT 2. Unlock the seat cushion. Swing the 3. Hook the strap. whole seat up and forward. 1. Lower the outer head restraint to the When returning the second seat to its lowest position and pull up the cen- original position, put the holding strap into ter head restraint.
Page 56 CAUTION When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: Make sure the seat is securely locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion.
Page 57 —Adjusting third seats —Tumbling third seats SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lever toward you. Then lean back to the desired angle and release the lever. CAUTION I13377b Avoid reclining the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the third seat passengers are sitting up...
Page 58 I13262c 2. Make sure the shoulder belt passes TUMBLING THIRD SEAT 2. Unlock the seat cushion and slide through the hanger when folding the the whole seat the rear−most 1. Lower the head restraint to the low- third seat. position while pulling up the handle. est position.
Page 59 13c558 13c559 13c557a 3. Swing the whole seat up. 4. Hook the strap. 5. Remove the seat hook covers from the back of the seat cushion, and When returning the third seat to its origi- install them over the seat hooks. nal position, put the holding strap into the hole.
Page 60 —Removing third seats CAUTION When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: Make sure the seat is securely locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion.
Page 61: Head Restraints
Head restraints CAUTION When reinstalling the seat, be care- ful not to hit the seat against you When removing or reinstalling the or inside of the vehicle. seat, observe the following precau- Install each seat in the same posi- tions to prevent personal injury: tion from which it was removed.
Page 62: Seat Heaters
Seat heaters For your safety and comfort, adjust the Right side CAUTION head restraint before driving. front seat To raise: Pull it up. Occupants must use caution when op- To lower: Push it down while pressing the erating the seat heater because it lock release button.
Page 63: Seat Belts
Seat belts— —Seat belt precautions Toyota strongly urges that the driver and Do not allow any children to stand up or NOTICE passengers in the vehicle be properly re- kneel on either rear or front seats. An strained at all times with the seat belts...
Page 64 —Fastening 3−point seat belts CAUTION Be careful not to damage the belt webbing or hardware. Take care that Persons should ride in their seats they do not get caught or pinched properly wearing their seat belts in the seat or doors. whenever vehicle moving.
Page 65 If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed, because it cannot protect an adult occupant or your child from death or serious...
Page 66 CAUTION Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be l13197b kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in a colli- sion.
Page 67 If the seat belt does not function Keep as low on hips as possible normally, immediately contact your Toyota dealer. Do not use the seat Sit up straight and well back in the Remove excess length of the belt and until the seat belt is fixed, because seat.
Page 68 Toyota dealer free of charge. Please contact your local Toyota dealer so that the dealer can order the proper re- quired length for the extender. Bring the heaviest coat you expect to wear for prop- er measurement and selection of length.
Page 69 Make sure the front passenger oc- Do not use the seat belt extender cupant classification indicator light when installing child restraint indicates “ON” when using the seat system on the front or rear passen- belt extender for the front passen- ger seat.
Page 70 If the seat belt does not function normally, immediately contact your The driver and front passenger seat belt Toyota dealer. Do not use the seat pretensioners are designed to be acti- until the seat belt is fixed, because vated in response to a severe frontal...
Page 71: Roll Sensing Of Curtain Shield Airbags Off Indicator Light
The front passenger’s seat belt pretension- CAUTION er will not activate if no passenger is detected in the front passenger seat by Make sure the roll sensing of cur- the front passenger occupant classification tain shield airbags indicator system. However, the front passenger’s light is not on.
Page 72 Failure to follow these instructions switch able the system, which could result can result in death or serious inju- in death or serious injury. ries. Consult your Toyota dealer 5. Seat belt pretensioner assemblies about any repair and modification. 6. Airbag sensor assembly...
Page 73: Buzzers" On
Do not perform any of the following assemblies, curtain shield airbag sensor changes without consulting your assemblies, driver’s seat position sensor, Toyota dealer. Such changes driver’s seat belt buckle switch, front pas- interfere with proper operation of the seat belt...
Page 74: Srs Airbags
In the following cases, contact your Toyota The SRS (Supplemental Restraint Sys- dealer as soon as possible: tem) front airbags are designed to pro-...
Page 75 The driver and front passenger can child restraint system. Toyota The SRS front passenger airbag will not be killed or seriously injured by the strongly recommends that all in- activate if there is no passenger sitting in inflating airbags if they do not wear fants and children be placed in the the front passenger seat.
Page 76 The SRS front airbags are designed to deploy in severe (usually frontal) colli- sions where the magnitude and duration of the forward deceleration of the ve- Hitting a curb, Falling into or hicle exceeds the designed threshold edge of pavement jumping over a level.
Page 77 8. Driver’s seat position sensor Deployment of the airbags happens in a fraction of a second, so the airbags must 9. Airbag sensor assembly inflate with considerable force. While the 10. Airbag module for driver system is designed to reduce serious inju- (airbag and inflator) ries, primarily to the head and chest, it The airbag sensor assembly consists of a...
Page 78 SRS driver’s air- can be killed or seriously injured. bag system will judge that the driv- Toyota strongly recommends that: er wears the seat belt even if not wearing it. In this case, the driver’s The driver sit as far back as pos-...
Page 79 “Child should not hold objects in their serious injury. restraint” on page 83. arms or on their knees. Failure to follow these instructions can result in death or serious injury. Consult your Toyota dealer about any repair and modification.
Page 80 Toyota dealer. It may assemblies, curtain shield airbag sensor dangerously interfere with the SRS assemblies, driver’s seat position sensor, front airbags operation.
Page 81 The SRS side airbag on the passenger seat will not activate if there is no pas- In the following cases, contact your Toyota The SRS (Supplemental Restraint Sys- senger sitting in the front passenger seat. dealer as soon as possible:...
Page 82 To ensure maximum protection child restraint system. Toyota in an accident, the driver and all strongly recommends that all in- passengers vehicle must fants and children be placed in the...
Page 83 When you push the roll sensing of curtain CAUTION shield airbags off switch for a few sec- onds with the ignition switch on, the roll Make sure the roll sensing of cur- sensing of curtain shield airbags off indi- tain shield airbags indicator...
Page 84 Collision from the rear Collision from the front The angle of Skidding vehicle vehicle tip−up hitting a curb Vehicle rollover is marginal stone The SRS side airbag and curtain shield The SRS side airbags are not generally The curtain shield airbags may inflate airbag system may not activate if the designed to inflate if the vehicle is in- if the angle of vehicle tip−up is margin-...
Page 85 Collision from Falling into or jump- Hitting a curb, edge of Collision from 13c538d the front ing over a deep hole pavement or hard sur- the rear face Pitch end over end Landing hard or vehicle falling The curtain shield airbags are not gen- The SRS side airbags and curtain shield The SRS side airbag and curtain shield erally designed to inflate if the vehicle...
Page 86 7. Curtain shield airbag sensors When the airbags inflate, they produce a CAUTION fairly loud noise and release some smoke 8. Side and curtain shield airbag sensors and residue along with non−toxic gas. This 9. Airbag sensor assembly SRS side airbags and curtain shield does not indicate a fire.
Page 87 Sit up straight and well back in the seat, distributing your weight evenly in the seat. Do not apply excessive weight to the outer side of the seats with a side airbag and to the front and rear pillar, front, center 13c562 and rear garnish and roof interior with the curtain shield airbag.
Page 88 Do not allow anyone to kneel on the passenger seat, facing the pas- senger’s side door, since the side airbag and curtain shield airbag could inflate with considerable speed and force. Otherwise, he/she may be killed or seriously injured. 13c563 Special care should be taken espe- cially when you have a small child in the vehicle.
Page 89 Do not hook a hanger, heavy or sharp pointed objects on the coat hook. If the curtain shield airbags inflate, those items will be thrown away with great force or the curtain shield airbags may not activate cor- 13c800b rectly, resulting in death or serious injury.
Page 90 Such changes may disable curtain shield airbags to inflate ac- Toyota dealer. Such changes can in- the system or cause the curtain cidentally, resulting in death or seri- terfere with proper operation of the shield airbags to inflate accidental- ous injury.
Page 91 It goes off after about 6 seconds. This or seat belt pretensioners. Contact your means the SRS side airbags and curtain Toyota dealer as soon as possible. shield airbags are operating properly. The light does not come on when the ignition key is turned to the “ON”...
Page 92 —Front passenger occupant classification system In the following cases, contact your Toyota Your vehicle is equipped with a front dealer as soon as possible: passenger occupant classification sys- tem. This system detects the conditions Any of the SRS side airbags and cur- 1.
Page 93 If the front passenger occupant classifica- Make sure that the “ON” indicator is illu- tion system determines that a person of minated when an adult is seated in the adult size sits in the front passenger seat front passenger seat. If the “OFF” indica- but the “OFF”...
Page 94 Condition and operation in the front passenger occupant classification system Indicator/ warning light Devices Condition detected by Curtain shield Front passenger Front Side airbag on Front the front passenger Front airbag in the SRS warning occupant passenger’s the front passenger’s occupant classification passenger front...
Page 95 CAUTION Do not recline the front passenger Wear the seat belt properly. seatback so far that it touches a Make sure the front passenger’s To avoid potential death or serious rear seat. This cause seat belt tab has not been left in- injury when the front passenger occu- “OFF”...
Page 96: Child Restraint
Child restraint— —Child restraint precautions Toyota strongly urges the use of ap- When it is unavoidable to install the Toyota strongly urges use of propriate child restraint systems for forward−facing child restraint sys- proper child restraint system which children. tem on the front passenger seat, conforms to the size of the child, The laws of all 50 states in the U.S.A.
Page 97 —Child restraint system A child restraint system for a small A forward−facing child restraint sys- Do not use the seat belt extender child or baby must itself be properly should allowed when installing child restraint restrained on the seat with the lap por- installed on front passenger system on the front or rear passen-...
Page 98 —Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer.
Page 99 —Installation with 2−point type seat belt (A) INFANT SEAT INSTALLATION 1. Run the center lap belt through or CAUTION around the infant seat following the An infant seat must be used in rear− instructions provided by its manufactur- facing position only. Do not install a child restraint sys- er and insert the tab into the buckle tem on the third seat if it interferes...
Page 100 2. While pressing the infant seat firmly Contact your Toyota dealer CAUTION against the seat cushion and seatback, immediately. Do not install the child tighten the lap belt by pulling its free...
Page 101 3. To remove the infant seat, press the (B) CONVERTIBLE SEAT INSTALLATION CAUTION buckle release button. A convertible seat must be used in for- ward−facing or rear−facing position de- Do not install a child restraint sys- pending on the age and size of the tem on the third seat if it interferes child.
Page 102 1. Run the center lap belt through or 2. While pressing convertible seat Contact your Toyota dealer around the convertible seat following firmly against the seat cushion and immediately. Do not install the child instructions provided...
Page 103 —Installation with 3−point type seat belt 13c564 3. To remove the convertible seat, press (A) INFANT SEAT INSTALLATION CAUTION the buckle release button. An infant seat must be used in rear− facing position only. Push and pull the child restraint sys- tem in different directions to be sure it is secure.
Page 104 Child restraint systems installed on the third seat should not contact the second seatbacks. 13c565 CAUTION Do not install a child restraint sys- tem on the second (or third) seat if Never install a rear−facing child re- it interferes with the lock mecha- straint system on the front passen- nism of the front (or second) seats.
Page 105 1. Run the lap and shoulder belt through 2. Fully extend the shoulder belt to put it Contact your Toyota dealer or around the infant seat following the in the lock mode. When the belt is immediately. Do not install the child...
Page 106 3. While pressing the infant seat firmly 4. To remove the infant seat, press the CAUTION against the seat cushion and seatback, buckle release button and allow the let the shoulder belt retract as far as belt to retract completely. The belt will Push and pull the child restraint sys- it will go to hold the infant seat secure- move freely again and be ready to...
Page 107 Install the child restraint system on the 6. While pressing convertible seat front passenger seat only when it is un- firmly against the seat cushion and avoidable. Your vehicle is equipped with a seatback, let the shoulder belt retract front passenger occupant classification...
Page 108 Remove the child restraint the front passenger airbag and side Never install a rear−facing child re- system and contact your Toyota dealer. airbag on the front passenger seat straint system on the front passen- could deploy.
Page 109 On vehicle with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar, front, center or rear 13c568 13c501b garnish or roof interior from which...
Page 110 1. Run the lap and shoulder belt through Contact your Toyota dealer or around the convertible seat following immediately. Do not install the child instructions provided restraint system on the seat until manufacturer and insert the tab into the seat belt is fixed.
Page 111 2. Fully extend the shoulder belt to put it 3. While pressing convertible seat CAUTION in the lock mode. When the belt is firmly against the seat cushion and then retracted even slightly, it cannot seatback, let the shoulder belt retract Push and pull the child restraint sys- be extended.
Page 112 13c569 13c570 Move seat fully back 4. To remove the convertible seat, press (C) BOOSTER SEAT INSTALLATION CAUTION the buckle release button and allow the A booster seat must be used in for- belt to retract completely. The belt will ward−facing position only.
Page 113 On vehicle with side airbags and CAUTION curtain shield airbags, do not allow the child to lean his/her head or Always make sure the shoulder belt any part of his/her body against the is positioned across the center of door or the area of the seat, front child’s shoulder.
Page 114 Contact your Toyota dealer immediately. Do not install the child 13C001 restraint system on the seat until the seat belt is fixed. 2. To remove the booster seat, press the...
Page 115 Symbol 13C003 13C004 Anchor brackets Use the anchor bracket located behind the TO USE THE ANCHOR BRACKET: 2. Fix the child restraint system with second seat on the floor to attach the top the seat belt. 1. Remove the head restraint. strap.
Page 116 —Installation with child restraint lower anchorages 13C005 13C529 13c571 Most upright position 4. Replace the head restraint. The lower anchorages for the child re- CHILD RESTRAINT SYSTEM INSTALLA- TION straint system interfaced with FMVSS225 specification are installed in 1. Fold down the seatback and back to the second seat.
Page 117 3. Type A—Latch the hooks of lower straps onto anchorages tighten the lower straps. Type B—Latch the buckles onto the anchorages 13C532f 13C009b If your child restraint system has a top strap, it should be anchored. (For the installation of the top strap, see “—Using a top strap”...
Page 118 CAUTION When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught. Push and pull the child restraint system in different directions to be sure it is secure.
Page 120 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Power tilt and telescopic steering wheel ..... . . Outside rear view mirrors .
Page 121: Power Tilt And Telescopic Steering Wheel
This feature can be set inoperative. Ask ries. your Toyota dealer.
Page 122: Outside Rear View Mirrors
—Power rear view mirror control Outside rear view mirrors— CAUTION Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.
Page 123: Anti−Glare Inside Rear View Mirror
Anti−glare inside rear view mirror— —Folding rear view mirrors NOTICE If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror. 13C010b The rear view mirrors can be folded Adjust the mirror so that you can just backward for parking in compact areas.
Page 124 —Compass (vehicles without navigation system) When the ignition key is inserted and turned on, the inside rear view mirror al- ways turns on in the “AUTO” mode. When the inside air temperature is low, it may take a little longer for the mirror to darken in response to the detection of 13c570b 13c013...
Page 125 Pushing the “AUTO” button for longer NOTICE than 3 seconds turns on or off the compass display. Do not put magnets or a metal object near the inside rear view mirror. Do- The compass may not show the correct ing this may cause malfunction of the direction in the following conditions: compass sensor.
Page 126 If the direction is displayed several sec- onds after adjustment, the calibration is finished. CAUTION Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped. 13C015b Zone number L Hawaii is included in zone 6.
Page 127 Do not adjust the display while the If calibration cannot be performed because vehicle is moving. Be sure to adjust of the magnetized vehicle, etc., take your the display only when the vehicle is stopped. vehicle to Toyota dealer.
Page 128: Sun Visors
Sun visors— —Vanity mirror To block out glare, move the sun visor. To block the glare from the front when the To use the vanity mirror, swing down main sun visor is swung down, swing the main sun visor and open the cover. To block out glare from the front—Swing down the second sun visor.
Page 130 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlight and turn signals ........Emergency flashers .
Page 131: Headlight And Turn Signals
NOTE: *The operating condition or sensi- tivity can be changed. Ask your Toyota dealer for details. HEADLIGHTS The automatic light control sensor is on the top of the passenger’s side instrument...
Page 132 “LOCK” but- ton on the wireless remote control key turns off the headlights. NOTE: *The time before turning off the lights can be changed. Ask your Toyota dealer for details. NOTICE To prevent the battery from being dis-...
Page 133: Emergency Flashers
Emergency flashers Instrument panel light control NOTICE To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running. To turn on the emergency flashers, To adjust the brightness of the instru- push the switch.
Page 134: Front Fog Lights
Front fog lights Interior lights To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”— —Center: Turn the light on when any of side doors and back door are opened.
Page 135: Personal Lights
One front door will be closed with the lock knob pushed forward while the other doors are locked. NOTE: *The interior lights can be set not to come on or the duration of lighting can be changed. Ask your Toyota dealer for details. Center...
Page 136: Ignition Switch Light
Ignition switch light Windshield wipers and washer To turn on the personal light, push the switch on side 1. To turn the lights off, push the switch on side 2. PERSONAL LIGHTS CUT OFF OPERA- TION When the ignition switch is “OFF” and any personal lights in the vehicle stay lighting on, the lights will cut off automatically after 30 minutes.
Page 137: Rear Window Wiper And Washer
If a nozzle becomes blocked, To squirt washer fluid on the rear window, twist the knob upward or downward as far contact your Toyota dealer to have the as it will go (position 3 or 4). The knob vehicle serviced.
Page 138: Rear Window Defogger
Rear window defogger Outside rear view mirror heaters Make sure you turn the defogger off when the surfaces are clear. Leaving the defog- ger on for a long time could cause the battery discharge, especially during stop−and−go driving. The defogger is not designed for drying rain water or for melt- ing snow.
Page 139 CAUTION Since the mirror surfaces can get hot, do not touch them when the mirror heater switch is on. Make sure you turn the mirror heaters off when the surfaces are clear. Leaving the mirror heaters on for a long time could cause the battery to discharge, especially during stop−and−go driving.
Page 140: Engine Oil
SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge ..........Engine coolant temperature gauge .
Page 141: Fuel Gauge
Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. 15C004 The gauge indicates the approximate...
Page 142: Engine Oil Pressure Gauge
If the engine oil pressure should stay be- low the normal range, pull off the road to a safe place and stop the engine immedi- ately. Call a Toyota dealer or qualified repair shop for assistance. Engine oil pressure may not build up when the engine oil level is too low.
Page 143: Voltmeter
Voltmeter Tachometer NOTICE Do not let the indicator needle get into the red zone. This may cause severe engine damage. The voltmeter tells whether the battery The tachometer indicates engine speed is charged discharged. Check in thousands of rpm (revolutions per while the engine is running—the needle minute).
Page 144: Odometer And Two Trip Meters
Odometer and two trip meters 3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back to the odometer each time you push.
Page 145: Service Reminder Indicators And Warning Buzzers
Service reminder indicators and warning buzzers If the indicator or buzzer comes on... Do this. If parking brake is off, stop immediately and contact Toyota dealer. (indicators and buzzer) Fasten driver’s seat belt. (indicators and buzzer) Fasten front passenger’s seat belt.
Page 146 If the indicator or buzzer comes on... Do this. Take vehicle to Toyota dealer immediately. Take vehicle to Toyota dealer. If brake system warning light is also on, stop immedi- ately and contact Toyota dealer. Close all side doors and back door.
Page 147 It is dangerous to continue driving Depressing the brake pedal repeatedly a safe place and contact your Toyota normally when the brake fluid level is may turn on the warning light and dealer.
Page 148: Engine Oil
Once the ignition key is turned to “ON” or safe place and contact your Toyota “START”, the reminder light flashes if a You need to reset the light after the en- dealer.
Page 149 Have your vehicle the tank as soon as possible. after taking several driving trips. checked by your Toyota dealer as soon as If the lamp will not go off even after sev- possible. eral trips, contact your Toyota dealer as Even if the abnormality of the electronic soon as possible.
Page 150 Contact your It goes off after about 6 seconds. This pant classification system. Toyota dealer as soon as possible to means the SRS airbags and seat belt service the vehicle. pretensioners are operating properly.
Page 151 Although it is no problem to continue If the light does not go off, call a Toyota (j) Open Door Warning Light driving, have your vehicle checked by...
Page 152 OFF” indicator light come on, have your the key when you open the driver’s door 5. Turn the ignition key to “ON”, but do vehicle checked by Toyota dealer as soon with the ignition key in the “ACC” or not start the engine.
Page 153: Trip Information Display
Trip information display (vehicles without navigation system) The following information is shown with Average vehicle speed Driving distance after engine starting the ignition key turned on. Each time The average vehicle speed is calculated The driving distance after engine start- you push the “MODE”...
Page 154 Available driving range Average fuel consumption after re- Current fuel consumption fueling The available driving range is calcu- The current fuel consumption is calcu- lated and displayed depending on the The average fuel consumption after re- lated and displayed based on the driv- amount of remaining fuel.
Page 156 ..........Active height control suspension (AHC) ..... . . Skyhook TEMS (Skyhook Toyota electronic modulated suspension)
Page 157: Ignition Switch
Ignition switch “ACC”—Accessories such as the radio Approximately five hours after the engine operate, but the engine is off. is turned off, you may hear a sound com- ing from underneath the luggage compart- If you leave the key in the “ACC” or ment for several minutes.
Page 158: Automatic Transmission
Automatic transmission Selector lever position P: Parking, engine starting and key removal position R: Reverse position N: Neutral position D: Normal driving position (Shifting into overdrive position) 4: Position for engine braking (Shifting into overdrive not possible) 3,2: Position for more powerful engine braking L: Position for maximum engine braking "...
Page 159 Your automatic transmission has a shift 3. Release the parking brake and brake Shift into the “L” position. The trans- lock system to minimize the possibility of pedal. Depress the accelerator pedal mission will downshift to first gear incorrect operation. This means you can slowly for smooth starting.
Page 160 (c) Using “3”, “2” and “L” positions (d) Backing up NOTICE The “3”, “2” and “L” positions are used for 1. Bring the vehicle to a complete stop. z Be careful not to over-rev the en- strong engine braking as described pre- 2.
Page 161 If the four–wheel drive control is in the When towing a trailer, in order to main- For ordinary driving, Toyota recommends “N” position while the selector lever is in tain engine braking efficiency, do not using the Normal mode to improve fuel the “P”...
Page 162: Four-Wheel Drive System
Four–wheel drive system— (a) Four–wheel drive contro l (i) If you cannot shift the selector le- Use the center differential lock system if ver out of “P” position your wheels get stuck in a ditch, or when you are driving on a slippery or bumpy If you cannot shift the selector lever from surface.
Page 163 “H” (high speed position, center differ- In this mode, the braking feeling that oc- The center differential lock system opera- ential unlocked): Lever at “H”, center dif- curs when the wheels are negotiating a tion is not completed within 5 seconds ferential lock button left out sharp corner is further reduced than in the while the cruise control system is set,...
Page 164 (b) Shifting procedure Use the “L” position of the automatic SHIFTING BETWEEN “H” (UNLOCKED) NOTICE AND “H” (LOCKED) transmission lever for maximum power and traction when your wheels get stuck For normal driving on dry and hard shift between unlock lock or when you drive down a steep incline.
Page 165: Active Traction Control System
If the “VSC/TRAC” warning light comes controlling the output of the brake and on, have your vehicle checked by your engine. Thus, the system assists driver Toyota dealer as soon as possible. control driving power wheels. When you turn the ignition...
Page 166 (The continuous buzzer sounds for about In the following cases, contact your Toyota snow tires or tire chains. Always 3 seconds.) At the time, the “VSC/TRAC”...
Page 167: Vehicle Stability Control System
When replacing the tires or wheels, The vehicle stability control system is acti- substitute for safe driving practices. contact your Toyota dealer. (See vated when the vehicle speed is about Factors including speed, road con- “Checking and replacing tires” on more than 15 km/h (9 mph).
Page 168 If the “VSC/TRAC” warning light and “VSC OFF” indicator light come on, have your vehicle checked by your Toyota dealer as soon as possible. However, there is no problem if the “VSC/TRAC” warning light comes on when the brake actuator tem- perature becomes high.
Page 169: Tire Pressure Warning System
If the continue to drive. tire inflation pressure becomes low, the In the following cases, contact your Toyota light comes on again. In this case, adjust- dealer: ing the tire inflation pressure will turn off The “VSC/TRAC”...
Page 170 The tire pressure warning that you have a flat tire. Check the light will turn off after a few minutes. tires. If the tire is flat, change to the spare tire and have the flat tire repaired by the nearest Toyota deal-...
Page 171 As an added safety feature, your ve- Your vehicle has also been equipped TPMS (tire pressure warning system) hicle has been equipped with a tire with a TPMS (tire pressure warning malfunction may occur for a variety pressure monitoring system (TPMS– system) malfunction indicator to indi- of reasons, including the installation tire pressure warning system) that il-...
Page 172 16C522a replaced, have them repaired or re- If a radio set at similar frequencies is placed by the nearest Toyota dealer in use in the vehicle. or an authorized tire dealer. The If a window tint that affects the radio tire pressure warning valves and wave signals is installed.
Page 173 Even if you use genuine wheels, the tire This device complies with Part 15 of the Reorient or relocate the receiving an- pressure warning system may not work FCC Rules. Operation is subject to the tenna. properly with some types of tires. following two conditions: Increase the separation between the Pushing the tire pressure warning reset...
Page 174 ID code of tire pres- sure warning valve and transmitter. Have the ID code registered by your Toyota dealer. If the ID code is not registered, the sys- tem will not work properly. After about 1...
Page 175 If initialization not performed. cannot be performed, have the system checked at your Toyota dealer. If you push the tire pressure reset switch accidentally and initialization is performed, adjust the tire inflation pressure to the specified level and initialize the system...
Page 176: Parking Brake
16C524a When you replace a new set of tires, purchase tire pressure warning valves and transmitters from your Toyota dealer and have the new ID code registered by your Toyota dealer. If the tire pressure select switch is set to the wrong tire setting, the system will not work properly.
Page 177: Cruise Control
Cruise control The cruise control is designed to main- CAUTION CAUTION tain a set cruising speed without requir- ing the driver to operate the accelera- Before driving, be sure the parking To help maintain maximum control tor. Cruising speed can be set to any brake is fully released and the park- of your vehicle, do not use the speed above 40 km/h (25 mph).
Page 178 CAUTION To avoid accidentally engaging the cruise control, turn the system off when it is not in use. Make sure the “CRUISE” indicator light is off. TURNING THE SYSTEM ON AND OFF SETTING THE CRUISING SPEED To turn the cruise control on, press the The transmission must be in “D”...
Page 179 Toyota deal- control lever down in the “– SET” direc- itself under certain circumstances. Tempo- er at the earliest opportunity.
Page 180: Active Height Control Suspension (Ahc)
The indicator light goes out after it (a) Vehicle height modes comes on. “HI” (high) mode— If this is the case, contact your Toyota The vehicle height is about 40 mm (1.6 dealer and have your vehicle inspected. in.) higher at front and about 50 mm (2.0 in.) higher at rear than the normal...
Page 181 When the vehicle exceeds the specified Extra high mode— “N” (normal) mode— vehicle speed, vehicle height This mode automatically selected The vehicle height in this mode is stan- changes to the following: from the high mode with the four−wheel dard. With the four−wheel drive control lever drive control lever placed in “L”...
Page 182 (b) Automatic leveling function (c) Vehicle height mode changing In the following cases the active height condition control suspension does not operate Regardless of the number of occupants even if the above conditions are all To change the vehicle height, it is nec- or the luggage loading condition, the met.
Page 183 The vehicle height cannot be raised if NOTICE the vehicle load exceeds the following limits: z If you change the vehicle height fre- quently, the pump may overheat. To ∗ Up to 4 occupants plus about 280 kg prevent this, the active height con- (617 lb.) in the normal mode trol suspension should be stopped ∗...
Page 184 Selecting the high mode— NOTICE Push the height select switch on the “ ” Do not select the low mode in the side when the vehicle speed is under bumpy roads. If the underbody of the about 30 km/h (19 mph). vehicle touches the rugged road sur- To change the normal mode to high, face, the vehicle may be damaged.
Page 185 z If your vehicle gets ditched, turn off CAUTION the active height control suspension with height control switch. If you drive through deep water over Otherwise, the vehicle height may about 500 mm (20 in.) in depth, put change because of the automatic the vehicle height in the HI (High) leveling function, resulting in an ac- mode with the active height select...
Page 186 With the active height control suspen- If the vehicle is loaded heavily, the ve- sion turned off, if you operate the hicle height cannot be raised even if height select switch the vehicle the height select switch is operated. If height is changing depending on the underbody vehicle...
Page 187 Toyota dealer as soon as possible. tact with the underbody of the vehicle. ing limits. The vehicle changes to the se- The height control “OFF”...
Page 188: Skyhook Tems (Skyhook Toyota Electronic Modulated Suspension)
“OFF” indicator blinks again, bring your mode select switch to provide good rid- ing comfort and stability. vehicle to your Toyota dealer as soon as possible and have it checked. 1. For driving on a bumpy road 2. For ordinary driving such as in the city traffic 3.
Page 190 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Audio system Reference ..........Using your audio system .
Page 191: Audio System
—some basics Reference This section describes some of the basic SWITCHING BETWEEN FUNCTIONS features on Toyota audio systems. Some Push “AM·SAT”, “FM”, “TAPE” or “DISC” information may not pertain to your sys- if the system is already on but you want tem.
Page 192 Satellite tuner technology notice: TONE AND BALANCE You must enter into a separate service Toyota’s satellite radio tuners are awarded For details about your system’s tone and agreement with the XMr radio in order to Type Approval Certificates from XMr Sat-...
Page 193 For the installation performed during antenna extension. The of the window tint, consult with maximum extension length is 850 mm your Toyota dealer. (33.5 in.). Every time you turn the radio on, the antenna will extend to its previous posi- tion.
Page 194 YOUR COMPACT DISC PLAYER CAUTION When you insert a disc, gently push it in with the label side up. Before extending the antenna, confirm The discs set in the player are played that no one is close enough to get continuously, starting with disc number 1.
Page 195 —Controls and features Details of specific buttons, controls, and features are described in the alphabetical list that follows. 17c517d...
Page 196 The button number will appear on the *: Use of satellite radio requires XMr tuner the discs will be automatically cancelled. display. and service. Contact your Toyota dealer for details. (Program) To tune in to a preset station: Push the button for the station you want.
Page 197 “AM” to switch from cassette or compact display. *: Use of satellite radio requires XMr tuner disc operation to radio operation. To stop the tape while it is fast forward- and service. Contact your Toyota dealer AUDIO−TUNE Knob ing, push fast...
Page 198 After FM button your vehicle to your Toyota dealer. pushing the button, insert a compact disc. Push “FM” to turn on the radio and select DISC At this time, the indicators on both sides the FM band. “FM1” or “FM2” will appear of the slot are flashing.
Page 199 Loading multiple compact discs— RAND (Random) RDS (Radio Data System) display To load multiple compact discs, push and There are two random features—you can The radio will automatically switch to the hold (until you hear a beep when the au- either listen to the tracks on all the com- RDS mode to receive an RDS station dio system is on).
Page 200 The player will repeat all the tracks on the the surrounding antenna cable. See a another channel. disc you are listening to. When the disc Toyota certified dealer. “– – –”: The channel you selected is no ends, the player will automatically go back “UPDATING”: longer available.
Page 201 *: Use of satellite radio requires XMr tuner XMr satellite radio*— Compact Disc Player and service. Contact your Toyota dealer You can either scan the currently selected There are two scan features—you can ei- for details. channel category or scan only the preset...
Page 202 *: Use of satellite radio requires XMr tuner After the beginning of the tape is the amount of channel separation to prev- and service. Contact your Toyota dealer reached, the player will automatically ent the weak signal from creating noise.
Page 203 : Use of satellite radio requires XMr If the entire disc or track title does not tuner and service. Contact your Toyota appear on the display, push and hold the If the entire the message is not displayed, dealer for details.
Page 204: Audio System Operating Hints
*: Use of satellite radio requires XMr tuner RADIO RECEPTION Each time you push the “ ” or “ ”, the and service. Contact your Toyota dealer Usually, a problem with radio reception program type changes as in the following: for details.
Page 205 *: Use of satellite radio requires XMr tuner ened, and there is another strong station and service. Contact your Toyota dealer nearby on the FM band, your radio may for details. tune in the second station until the origi-...
Page 206 CARING FOR YOUR CASSETTE PLAYER Avoid using cassettes with a total play- If this equipment does cause harmful AND TAPES ing time longer than 100 minutes (50 interference to radio or television re- minutes per side). The tape used in For the best performance for your cas- ception, which can be determined by these cassettes is thin and could get...
Page 207 CARING FOR YOUR COMPACT DISC PLAYER AND DISCS The player is intended for use with 12 cm (4.7 in.) discs only. Extremely high temperatures can keep your compact disc player from working. On hot days, use the air conditioning to cool the vehicle interior before you listen to a disc.
Page 208 NOTICE z Do not use special shaped, trans- parent/translucent, low quality or la- beled discs such as those shown in the illustrations. The use of such discs may damage the player or changer, or it may be impossible to eject the disc. z This system is not designed for use Correct Wrong...
Page 209: Rear Seat Audio System
Rear seat audio system (b) When the radio mode is selected “ ” button: Push this button to select a preset station on the preset but- ton of the front audio system. Each push of the button changes to the station with higher numbered preset button.
Page 210: Audio Remote Controls (Steering Switches)
Audio remote controls (steering switches) (c) When the “TAPE” mode is selected (e) Some basics “ PROG ” button: Push this button This system cannot be used if the audio system is not turned on. to select the other side of a cassette tape.
Page 211 XMr satellite radio*— To select a preset channel, push the “ ” or “ ” side of the switch. Repeat until a desired channel is found. *: Use of satellite radio requires XMr tuner and service. Contact your Toyota dealer for details.
Page 212: For Vehicle Equipped With Navigation System, Please Refer To The Separate "Navigation System Owner's Manual
SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Front air conditioning system: Controls ..........Air flow selector settings .
Page 213: Front Air Conditioning System: Controls
Front air conditioning system— —Controls 1. Temperature selector knob 2. “AUTO” button 3. Temperature display 4. Fan speed display 5. Air flow display 6. “MODE” button 7. “A/C” button 8. Windshield air flow button 9. Fan speed control button 10. Air intake control button 11.
Page 214 “AUTO” button “MAX COLD” appears when you adjust to maximum cooling, and “MAX HOT” ap- For automatic operation of the air condi- pears when you adjust to maximum warm- tioning, press the “AUTO” button. An indi- ing. cator light will illuminate to show that the automatic operation mode has been se- “OFF”...
Page 215 4. Floor/Windshield—Air flows mainly When the “A/C” button is not pressed in, from the floor vents and windshield pressing “MODE” button turns off the air vents. conditioning. It is recommended that you close the For details about air flow selector setting, lower vent.
Page 216 If this happens, take your ve- hicle to a Toyota dealer for service. Air intake control button Press the button to select the air source. An indicator light will illuminate to show which air intake mode is being selected.
Page 217: Air Flow Selector Settings
—Air flow selector settings —Operating tips To cool off your Toyota after it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.
Page 218 If following another vehicle on a dusty Heating Air conditioning road, or driving in windy and dusty For best results, set controls to: For best results, set controls to: conditions, it is recommended that the air intake control button be temporarily Fan speed—“AUTO”...
Page 219: Instrument Panel Vents
—Instrument panel vents Defogging Defrosting The inside of the windshield The outside of the windshield For best results, set controls to: For best results, set controls to: Temperature— Towards high temperature Temperature—Towards high temperature to heat; Air intake—FRESH (outside air) low temperature to cool Air flow—WINDSHIELD Air intake—FRESH (outside air)
Page 220 Lower vent If air flow control is not satisfactory, check the instrument panel vents. The instrument panel vents may be opened or closed as shown. For removing frost or fog, it is recom- mended that you close the lower vent when you use the “Floor”, the “Floor/Wind- shield”...
Page 221: Rear Air Conditioning System
Rear air conditioning system— —Controls 1. Rear air conditioning on−off switch 2. “AUTO” button 3. Air flow selector 4. Fan speed selector 5. Temperature selector 6. “OFF” button 18c507b...
Page 222 Rear air conditioning on−off switch Temperature selector To turn the rear air conditioning on, press Move the lever to adjust the tempera- the “REAR” switch. To turn the rear air ture—to the right to warm, to the left to conditioning off, press the switch again. cool.
Page 223: Air Flow Selector Settings
—Air flow selector settings 18c508a Warm air Cool air...
Page 224 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Clock ............Outside temperature display .
Page 225: Clock
Clock Outside temperature display To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. The key must be in the “ACC” or “ON” position. If quick adjustment to a full hour is de- 18C510 sired, push the “:00”...
Page 226: Rear View Monitor System
Rear view monitor system The display indicates between the range The rear view monitor system assists CAUTION of –22°F and 122°F. the driver by displaying an image of the view behind the vehicle while back- The key must be in the “ON” position. Never depend on rear...
Page 227 When replacing the tires, please consult If the back of the vehicle is hit, the your Toyota dealer. If you replace the position and mounting angle of the tires, the area displayed on the screen camera may change. Be sure to may change.
Page 228 AREA DISPLAYED ON SCREEN When water droplets are adhering to the camera, or when humidity is high Image is displayed approximately level (for example, when it rains) on screen. When foreign matter (for example, The area detected by the camera is snow or mud) adheres to the camera limited.
Page 229: Cigarette Lighter And Ashtray
Do not hold the cigarette lighter pressed mitted by the camera, the light source appears to have a vertical streak above and below it. Use a Toyota genuine cigarette lighter or equivalent for replacement.
Page 230: Power Outlets
Power outlets The power outlets are designed for power supply for car accessories. To use them, open the lids as shown in the following illustrations. The key must be in the “ACC” or “ON” position to be used. NOTICE z To prevent the fuse from being blown, do not use the electricity over the total vehicle capacity of...
Page 231: Roll Sensing Of Curtain Shield Airbags Off Switch
Roll sensing of curtain shield airbags off switch In a severe side impact, the curtain shield CAUTION airbags on impacted side will inflate even if the roll sensing function is turned off. Make sure the roll sensing of cur- If the ignition switch is turned to “ACC” or off indicator light tain shield airbags “LOCK”...
Page 232: Rear Console Box
Rear console box Glove box Garage door opener Buttons Indicator light To use the rear console box, open as To use the glove box, do this. The garage door opener (HomeLink shown in the illustration. Universal Transceiver) is manufactured un- To open: Pull the lever.
Page 233 The battery side of the hand−held trans- mitter must be pointed away from the HomeLink during the programming pro- HomeLink cess. For Canadian users, follow the procedure 19C514 19C515 in “Programming an entrance gate/Pro- gramming all devices in the Canadian 25 to 75 mm market”.
Page 234 6. Repeat steps 2 through 5 for each re- 1. Locate the “training” button on the ceil- maining HomeLink button to program ing mounted garage door opener motor. another device. The exact location and color of the button may vary by brand of garage Programming a rolling code system door opener.
Page 235 Canadian market To program other devices such as home 1. Decide which of the 3 HomeLink but- security systems, home door locks or tons you want to program. lighting, contact your authorized Toyota dealer for assistance. 2. Place your hand−held gate/device 19C517 transmitter 25 to 75 mm (1 to 3 in.)
Page 236 FCC Rules and with RSS−210 of the IC ceiver call the: When programming the HomeLink Rules. Operation is subject to the fol- Toyota Customer Experience Center at Universal Transceiver, you may be lowing two conditions: (1) This device 1−800−331−4331 (U.S.A.)
Page 237: Auxiliary Boxes
Auxiliary boxes— To use the auxiliary boxes, open as shown in the following illustrations. CAUTION To reduce the chance of injury in case of an accident or a sudden stop, always keep the auxiliary box closed while driving. Type A (luggage compartment) Type C (rear console) Type B (luggage compartment)
Page 238: Cup Holders
—First−aid kit holder —Warning reflector holder Cup holders The cup holder is designed for holding cups or drink−cans securely. To use them, observe the following illustra- tions. CAUTION Do not place anything else other than cups or drink−cans in the cup holder, such items...
Page 239 19C008 For front seats For front seat For second seats The cup holder can be adjusted to the To use a cup holder in the console box. size of cups by changing the separator 1. Open the console box lid. Pull down position or moving the separator arms.
Page 240: Card Holder
Card holder Tie−down hooks For third seats (left−hand side) You can store a card in the slot as To secure your luggage, use the tie− shown in the illustration. down hooks as shown above. See “Cargo and luggage” on page 257 for precautions when loading luggage.
Page 241: Cargo Net Hooks
Cargo net hooks Roof luggage carrier Side Cross knobs rails Upper knob Roof rails These hooks are designed to hang car- The roof luggage carrier consists of ADJUSTING THE POSITION OF CROSS go net. roof rails and sliding cross rails. RAILS: To hang the cargo net, use the cargo net 1.
Page 242 Follow the manufacturer’s instructions and precautions when installing the attach- ments or their equivalent. CAUTION When you load cargo on the roof lug- gage carrier, observe the following: Place the cargo so that its weight is distributed evenly between the front and rear axles.
Page 243: Floor Mat
Floor mat If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then dur- ing the trip to make sure the cargo remains in its place. Do not exceed 70 kg (154 lb.) cargo weight on the roof luggage carrier.
Page 244: Coat Hooks
Coat hooks To use the coat hook, push the hook. CAUTION Do not hook a hanger, heavy or sharp pointed object on the coat hook. If curtain shield airbags inflate, those items will be hurled away with great force or the curtain shield air- bags may not active correctly.
Page 246: Engine Oil
SECTION INFORMATION BEFORE DRIVING YOUR TOYOTA Information before driving your Toyota Off−road vehicle precautionss .......
Page 247: Off−Road Vehicle Precautionss
Off−road vehicle precautions This vehicle belongs to the utility ve- CAUTION hicle class, which has higher ground clearance and narrower tread in relation Always observe the following precau- to the height of its center of gravity to tions to help minimize the risk of se- make it capable of performing in a wide rious personal injury or damage to variety of off−road applications.
Page 248: Break−In Period
To help prevent gas station mix−ups, your hicle more sensitive side to the future economy and long life of Toyota has a smaller fuel tank opening. winds than an ordinary passenger your vehicle: The special nozzle on pumps with un- car. Slowing down will allow you Avoid full−throttle...
Page 249 10% ethanol or 15% If you detect heavy knocking even when Automotive manufacturers in the U.S., MTBE. If you use gasohol in your Toyota, using the recommended fuel, or if you Europe and Japan have developed a...
Page 250: Fuel Pump Shut Off System
Operation in foreign countries GASOLINE QUALITY The fuel pump shut off system stops sup- If you plan to drive your Toyota in plying fuel to the engine when the engine another country... In a very few cases, you may experience stalls or an airbag inflates upon collision.
Page 251: Three−Way Catalytic Converter
The three−way catalytic converter is the z Use only unleaded gasoline. vehicle in for a check−up as soon emission control devices installed in as possible. Remember, your Toyota z Do not drive with an extremely low the exhaust system. dealer knows your vehicle and its fuel level;...
Page 252: Engine Exhaust Cautions
It gases to be drawn into the vehicle. Toyota Maintenance Schedule. For can cause unconsciousness or even To allow proper operation of your scheduled maintenance information, death.
Page 253: Facts About Engine Oil Consumption
(1.1 qt./600 miles, 0.9 Imp.qt/600 regularly. Toyota recommends that the oil by the high temperature combustion miles) level be checked every time you refuel gases during the combustion process.
Page 254: Iridium−Tipped Spark Plugs
In this case, the brakes may not work mance or smooth drivability. properly. If they do not work well, depress the brake pedal firmly. If the brake system warning light comes on, immediately stop your vehicle and contact your Toyota deal-...
Page 255 The brake system warning light may stay ANTI−LOCK BRAKE SYSTEM Depressing the brake pedal on slippery on for about 60 seconds after the ignition (with “ABS” warning light) road surfaces such as on a manhole cov- key is turned to “ON” position. It is nor- er, a steel plate at a construction site, The anti−lock brake system is designed mal if the light turns off after a while.
Page 256 CAUTION Anti−lock brake system is not de- signed to shorten the stopping dis- overestimate anti−lock tance: Always drive at a moderate brake system: Although the anti−lock speed and maintain a safe distance brake system assists in providing ve- from the vehicle in front of you. hicle control, it is still important to Compared with vehicles without an drive with all due care and maintain...
Page 257 Toyota dealer. When the “ABS” warning light is on (and Have your Toyota dealer perform the bed- In this case, not only the anti−lock the brake system warning light is off), the ding−down.
Page 258: Brake Pad Wear Limit Indicators
Toyota CAUTION dealer as soon as possible. Expensive ro- tor damage can result if the pads are not Do not allow more than one person replaced when necessary. to get on the rear step bumper at a time.
Page 259: Limited−Slip Differential
This is the primary identification number Use only a spare tire of the same for your Toyota. It is used in registering size, construction and load capacity the ownership of your vehicle. as the original tires on your Toyota because damage to the limited−slip...
Page 260: Theft Prevention Labels
—Engine number Theft prevention labels Suspension and chassis Your new vehicle carries theft preven- CAUTION tion labels which are approximately 47 mm (1.85 in.) by 12 mm (0.47 in.) or 56 Do not modify the suspension/chassis mm (2.20 in.) by 16 mm (0.63 in.). with lift kits, spacers, springs, etc.
Page 261: Tire Information
Tire information— —Tire symbols This illustration indicates typical tire symbols. 1. Tire size—For details, see “Tire size” on page 250. 2. DOT Tire Identification Number (TIN)—For details, see “DOT and Tire Identification Num- ber (TIN)” on page 249. 3. Tire ply composition and materi- als—Plies mean a layer of rubber−...
Page 262 —DOT and Tire Identification Number (TIN) 7. “TUBELESS” or “TUBE TYPE” The “DOT” symbol certifies that the —A tubeless tire does not have a tire conforms to applicable Federal tube inside the tire and air is direct- Motor Vehicle Safety Standards. ly filled in the tire.
Page 263 —Tire size —Name of each section of tire 20c506a 21A007a 21A006a This illustration indicates typical tire 1. Section width 1. Bead size. 2. Tire height 2. Sidewall 1. Tire (P=Passenger car, 3. Wheel diameter 3. Shoulder T=Temporary use) 4. Tread 2.
Page 264 150 would wear conditions on specified government purchasers of Toyota vehicles with in- one and a half (1−1/2) times as well test surfaces of asphalt and concrete. formation on uniform tire quality grad-...
Page 265 Temperature A, B, C—The tempera- ture grades are A (the highest), B, and C, representing the tire’s resis- tance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 266 —Glossary of tire terminology Tire related term Meaning tire inflation pressure when the vehicle has been parked for at least 3 hours Cold tire inflation pressure or more, or it has not been driven more than 1.5 km or 1 mile under that condition the maximum cold inflation pressure to which a tire may be inflated and it is Maximum inflation pressure...
Page 267 Tire related term Meaning the combined weight of those installed regular production options weighing over 2.3 kg (5 lb.) in excess of those standard items which they replace, not pre- Production options weight viously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim Vehicle capacity weight the rated cargo and luggage load plus 68 kg (150 lb.) times the vehicle’s desig-...
Page 268 Tire related term Meaning the load on an individual tire that is determined by distributing to each axle Vehicle normal load on the tire its share of the curb weight, accessory weight, and normal occupant weight (distributed in accordance with Table 1 that follows) and dividing by two Weather side the surface area of the rim not covered by the inflated tire Table 1–...
Page 269: Vehicle Load Limits
Vehicle load limits Vehicle load limits include total load NOTICE CAUTION capacity, seating capacity, towing ca- pacity and cargo capacity. Follow the Even if the number of occupants Do not apply the load more than load limits shown below. Total load ca- are within the seating capacity, each load limit.
Page 270: Cargo And Luggage
Cargo and luggage— —Stowage precautions When stowing cargo and luggage in NOTICE D Never allow anyone to ride in or on the vehicle, observe the follow- the luggage compartment. It is ing: Do not load the vehicle beyond not designed for passengers. the vehicle capacity weight giv- D Put cargo and luggage in the lug- They should ride in their seats...
Page 271 —Capacity and distribution Cargo capacity depends on the to- (4) The resulting figure equals the tal weight of the occupants. available amount of cargo and luggage load capacity. For exam- (Cargo capacity) = (Total load capac- ple, if the “XXX” amount equals ity) –...
Page 272 379 kg – 176 kg = 203 kg. CAUTION (834 lb. – 388 lb. = 446 lb.) Weight of removed As shown in the above example, if the third seat Even if the total load of occu- number of occupants increases, the pant’s weight and the cargo load Cargo cargo and luggage load equaling the...
Page 273: Types Of Tires
Types of tires Determine what kind of tires your All season tires, however, do not have vehicle is originally equipped with. adequate traction performance compared with snow tires in heavy or 1. Summer tires loose snow. Also, all season tires fall Summer tires are high−speed capabil- short in acceleration and handling ity tires best suited to highway driving...
Page 274 SECTION STARTING AND DRIVING Starting and driving Before starting the enginee ........How to start the engine .
Page 275: Before Starting The Enginee
How to start the engine— (a) Cranking hold function Before starting the engine (b) Before cranking 1. Check the area around the vehicle be- Once you turn the ignition key to “START” 1. Apply the parking brake firmly. fore entering it. position and release it, the cranking hold 2.
Page 276: Tips For Driving In Various Conditions
To dry them, drive vehicle cautiously while lightly pressing the brake pedal with the park- ing brake applied. If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance.
Page 277: Off−Road Driving Precautions
Off−road driving precautions When driving your vehicle off−road, please CAUTION Do not drive in excess of the speed observe the following precautions to en- limit. Even if the legal speed limit sure your driving enjoyment and to help Before driving off, make sure the permits it, do not drive over 140 prevent the closure of areas to off−road parking brake is fully released and...
Page 278 U.S. Forest Service and Bureau of NOTICE After driving through tall grass, Land Management mud, rock, sand, rivers, etc., check z If driving through water, such as that there is no grass, bush, paper, CAUTION when crossing shallow streams, rags, stone, sand, etc. adhering or first check the depth of the water trapped on the underbody.
Page 279: Winter Driving Tips
See page 325 for recommended viscosity. selection. Supplement”. Leaving a heavy summer oil in your ve- “Toyota Super Long Life Coolant” is a mix- hicle during winter months may cause ture of 50% coolant and 50% deionized harder starting. If you are not sure about water.
Page 280: Dinghy Towing
When parking, put the transmission into overload your vehicle or trailer. Ask your “P” and block the front wheels. Do not local Toyota dealer for further details be- use the parking brake, or snow or water fore towing. accumulated in and around the parking...
Page 281 WEIGHT LIMITS CAUTION Trailer hitch assemblies have differ- Before towing, make sure the total trail- ent weight capacities established by er weight, gross combination weight, The maximum gross trailer weight the hitch manufacturer. Even though gross vehicle weight, gross axle weight (trailer weight plus cargo weight) the vehicle may be physically capa- and trailer tongue load are all within...
Page 282 The load on either the front or rear Total trailer weight Tongue load axle resulting from distribution of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label. 20c508a Tongue load ∗...
Page 283 If you wish to install a trailer hitch, you weight in the back than in the Do not use axle−mounted hitches as should consult with your Toyota dealer. front. About 60% of the trailer load they can cause damage to the axle...
Page 284 Trailer Class Typical Trailer Ball Size 2 in. 2 in. 1 7/8 in. 2. Select the appropriate trailer ball to match exceed gross trailer weight rating of the trailer. The trailer ball load rating should be printed on the top of the ball. 3.
Page 285 220 (32) Never tap into your vehicle’s hy- BRAKES AND SAFETY CHAINS Rear 240 (35) draulic system as it would lower its Toyota recommends trailers with See Section 7−2 and Section 8 for in- braking effectiveness. brakes that conform to any applica- structions.
Page 286 BREAK−IN SCHEDULE 3. Turn the ignition switch on or push the height control switch to turn on the Toyota recommends that you do not active height control suspension. Select tow a trailer with a new vehicle or a the “N” (normal) mode with the height vehicle with any new power train com- select switch.
Page 287 4. Turn the ignition switch on or push the Check that your rear view mirrors con- Avoid jerky starts or sudden accelera- height control switch to turn on the form to any applicable federal, state/ tion. active height control suspension. provincial or local regulations.
Page 288 Crosswinds and rough roads will ad- Because of the added load of the trail- When restarting out after parking on a versely affect handling of your vehicle er, your vehicle’s engine may overheat slope: and trailer, causing sway. Pay attention on hot days temperatures over 1.
Page 289: How To Save Fuel And Make Your Vehicle Last Longer, Too
How to save fuel and make your vehicle last longer, too Improving fuel economy is easy–just take Avoid engine over-revving. Use a CAUTION it easy. It will help make your vehicle last gear position suitable for the road on longer, too. Here are some specific tips which you are travelling.
Page 290 Keep front wheels in proper CAUTION alignment. Avoid hitting the curb and slow down on rough roads. Improper Never turn off the engine to coast alignment not only causes faster tire down hills. Your power steering and wear but also puts an extra load on brake booster will not function with- the engine, which, in turn, wastes fuel.
Page 292: In Case Of An Emergency
SECTION IN CASE OF AN EMERGENCY In case of an emergency If your vehicle will not startt ........If your engine stalls while driving .
Page 293: If Your Vehicle Will Not Startt
2. If the engine still will not start, it needs work, your key may be broken. Have the adjustment or repair. Call a Toyota key checked at your Toyota dealer. If 3. If the light is out, dim or goes out dealer or qualified repair shop.
Page 294 If the engine still will not start, it needs which is poisonous and corrosive. adjustment or repair. Call a Toyota dealer Wear protective safety glasses when or qualified repair shop for assistance. jump starting, and avoid spilling acid on your skin, clothing, or ve- hicle.
Page 295 JUMP STARTING PROCEDURE 1. If the booster battery is installed in Discharged battery Jumper cable another vehicle, make sure the vehicles are not touching. Turn off all unneces- sary lights and accessories. Booster When boosting, use the battery of battery matching or higher quality.
Page 296 If the cause of your battery discharging is not apparent (for example, lights left on), When making connections, you should have it checked at your Toyota avoid serious injury, do not lean over dealer. the battery or accidentally let the jumper cables or clamps touch any- thing except the correct battery termi- nals or the ground.
Page 297: If Your Engine Stalls While Driving
CAUTION After arriving at a safe place, stop the vehicle and call a Toyota dealer for 2. If coolant or steam is boiling out of the If the engine is not running, the pow- assistance.
Page 298: If You Have A Flat Tire
You should have it checked as 4. If the engine drive belt is broken or the soon as possible at your Toyota dealer. 5. Read the following instructions coolant is leaking, stop the engine im- mediately.
Page 299 NOTICE CAUTION D Make sure to set the jack prop- erly in the jack point. Raising z Do not continue driving with When jacking, be sure to observe the vehicle with jack improper- a deflated tire. Driving even a the following to reduce the possi- ly positioned will damage the short distance can damage a bility of personal injury:...
Page 300 —Required tools and spare tire 1. Get the required tools and spare Turn the jack joint by hand. To remove the spare tire under the tire. luggage compartment: To remove: Turn the joint in direction 1 Tool bag 1 until the jack is free. 1.
Page 301 When connecting a jack handle exten- 2. Remove the access hole cover on 3. Insert the jack handle end into the sion with a jack handle end, use a the rear bumper with a flathead lowering screw through the access jack handle to tighten the bolts on the screwdriver.
Page 302 —Blocking the wheel 4. After the tire is lowered completely When storing the spare tire, put it in 2. Block the wheel diagonally op- to the ground, remove the holding place with the outer side of the wheel posite the flat tire to keep the bracket as shown in the illustration.
Page 303 —Removing wheel ornament —Loosening wheel nuts CAUTION Never use oil or grease on the bolts or nuts. The nuts may loos- en and the wheels may fall off, which could cause a serious ac- cident. 3. Remove the wheel ornament. 4.
Page 304 —Positioning the jack JACK POINTS: Front—Under the frame side rail Left rear—Under the rear axle housing Right rear—Under the bracket on the rear axle housing Make sure the jack is positioned on a level and solid place. Put a jack handle, jack handle exten- sions, and jack handle end together as shown in the illustration.
Page 305 —Raising your vehicle NOTICE Tighten all the joints securely. Otherwise, the extension may come off and it may damage the paint or vehicle body. When connecting a jack handle exten- 6. After making sure no one is in sion with another extension and a jack the vehicle, raise it high enough handle end, use a jack handle to tight- so that the spare tire can be...
Page 306 —Changing wheels To raise the vehicle, insert the jack handle end into the joint of the jack (it is a loose fit) and turn it clockwise with the handle, making sure the han- dle remains firmly fitted onto the jack handle extension.
Page 307 —Reinstalling wheel nuts —Lowering your vehicle CAUTION Never use oil or grease on the bolts or nuts. Doing so may lead to overtightening the nuts and damaging the bolts. The nuts may loosen and the wheels may fall off, which could cause a seri- ous accident.
Page 308 —Reinstalling wheel ornament Tighten each nut a little at a time in CAUTION the order shown. Repeat the process until all the nuts are tight. D Take due care in handling the ornament to avoid unexpected CAUTION personal injury. D When lowering the vehicle, D Do not attach a heavily dam- make sure all portions of your aged plastic wheel ornament.
Page 309: If Your Vehicle Becomes Stuck
If your vehicle becomes stuck —After changing wheels 11. Check the air pressure of the re- If your vehicle becomes stuck in snow, CAUTION mud, sand, etc., then you may attempt to placed tire. rock the vehicle free by moving it forward Adjust the air pressure to the specifi- Before driving, make sure all the and backward.
Page 310: If Your Vehicle Needs To Be Towed
If towing is necessary, we recommend NOTICE (a) Towing with wheel lift type truck— you have it done by your Toyota dealer or a commercial tow truck service. In If you rock your vehicle, observe the —From front consultation with them, have your ve- following precautions to prevent dam- hicle towed using either (a) or (b).
Page 311 “Active height control suspension” on page 167. (c) Towing with sling type truck If towing is necessary, we recommend you to have it done by your Toyota (a) Towing with wheel lift type truck NOTICE dealer or a commercial tow truck ser- Use a towing dolly under the wheels not vice.
Page 312 —Emergency towing hook precautions Before emergency towing, check that CAUTION CAUTION the hook is not broken or damage and that the installation bolts are not loose. Use extreme caution when towing ve- If the engine is not running, the pow- Fasten the towing cable or chain se- hicle.
Page 313: If You Cannot Shift Automatic Transmission Selector Lever
If the towing vehicle can hardly move, do not forcibly continue the If you cannot shift the selector lever towing. Contact your Toyota dealer out of “P” position to other positions or a commercial tow truck service even though the brake pedal is de- for assistance.
Page 314: If You Lose Your Keys
Toyota dealer if you can give them the key number and master key. Even if you lose only one key, contact your Toyota dealer to make a new key. If you lose all your master keys, you cannot make new keys; the whole engine immobi- lizer system must be replaced.
Page 316 ..... . . Washing and waxing your Toyota ......
Page 317 Now, it is up to be dry. to see all the mud and dirt. It will do you. Proper care of your Toyota can help more harm than good to simply wet the High ambient temperatures can cause ensure long−term corrosion prevention.
Page 318 Washing and waxing your Toyota Check the interior of your vehicle. Wa- Washing your Toyota Exhaust gases cause the exhaust ter and dirt can accumulate under the Keep your vehicle clean by regular pipe to become quite hot. When floor mats and could cause corrosion. Oc- washing.
Page 319 Toyota dealer to your vehicle. have the vehicle serviced. NOTICE NOTICE To prevent damage to the antenna, If a nozzle becomes blocked, do not...
Page 320 Cleaning the interior Exterior lights: Do not apply wax on the Vinyl interior CAUTION surfaces of the lights. Wax may cause The vinyl upholstery may be easily damage to the lenses. If you accidentally cleaned with a mild soap or detergent Vehicles with side airbags and cur- put wax on the light surfaces, wipe or and water.
Page 321 Carpets NOTICE NOTICE Use a good foam−type shampoo to z Do not use dye or bleach on the z Do not use organic substances (sol- clean the carpets. belts—it may weaken them. vents, kerosene, alcohol, gasoline, Begin by vacuuming thoroughly to remove etc.) or alkaline or acidic solutions.
Page 322 If you have any questions about the leather these could cleaning of your Toyota, your local cause discoloring. Toyota dealer will be pleased to answer them. z Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather.
Page 324 SECTION VEHICLE MAINTENANCE AND CARE Vehicle maintenance and care Maintenance requirementss ....... . . General maintenance .
Page 325: Maintenance Requirementss
See “Owner’s War- form them are presented in Section 7. or if you prefer, your Toyota dealer will be ranty Information Booklet” or “Owner’s pleased to do them at a nominal cost.
Page 326: General Maintenance
Radiator, condenser and hoses Supplement” for the details. vehicle to your Toyota dealer or a quali- Check that the front of the radiator and fied service shop immediately. It is recom- condenser are clean and not blocked with mended that any problem you notice be leaves, dirt, or insects.
Page 327 Exhaust system Seats Parking brake If you notice any change in the sound of Check that all front seat controls such as Check that the lever has the proper travel the exhaust or smell exhaust fumes, have seat adjusters, seatback recliner, etc. op- and that, on a safe incline, your vehicle the cause located and corrected immedi- erate smoothly and that all latches lock...
Page 328: Does Your Vehicle Need Repairing
If you notice any of these clues, take your tant clues are as follows: month. See page 330 for additional vehicle to your Toyota dealer as soon as information. Engine missing, stumbling, or pinging possible. It probably needs adjustment or repair.
Page 329: Emissions Inspection And Maintenance (I/M) Programs
Toyota dealer comes on. In this case, your vehicle may to prepare the vehicle for re−testing. not pass the I/M test and need to be repaired.
Page 330 SECTION − DO−IT−YOURSELF MAINTENANCE Introduction Engine compartment overview ....... Fuse locations .
Page 331: Engine Compartment Overview
Engine compartment overview 1. Suspension fluid reservoir 2. Engine oil filler cap 3. Brake fluid reservoir 4. Fuse block 5. Battery 6. Windshield and rear window washer fluid tank 7. Engine oil level dipstick 8. Condenser 71C004f 9. Radiator 10. Engine coolant reservoir 11.
Page 332: Fuse Locations
Fuse locations Spare fuses i71002d Spare fuses 71C510a...
Page 333: Do−It−Yourself Service Precautions
Right after driving, engine warranty coverage. Read separate automatically start to run if the air compartment—the engine, radiator, Toyota Warranty statement for details and conditioning is on. exhaust manifold, power steering suggestions. Use eye protection whenever you fluid reservoir spark...
Page 334: Parts And Tools
Remember all Toyota parts are de- trode. Do not dispose of used oil and fil- signed in metric sizes, so your tools must...
Page 335 Tools: CHECKING AND REPLACING FUSES Funnel (only for adding coolant) Parts (if replacement is necessary): CHECKING BRAKE FLUID Fuse with same amperage rating as original Parts (if level is low): ADDING WASHER FLUID SAE J1703 or FMVSS No.116 DOT 3 brake fluid Parts: Tools:...
Page 336: Engine Oil
SECTION − DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level ....... . . Checking the engine coolant level .
Page 337: Checking The Engine Oil Level
Checking the engine oil level NOTICE Low level Full level Be careful not to drop engine oil on the vehicle components. If the oil level is below or only slightly above the low level, add engine oil of the same type as already in the engine. Remove the oil filler cap and add engine oil in small quantities at a time, checking Add oil...
Page 338: Engine Oil
ENGINE OIL SELECTION SAE 5W−30 is the best choice for good fuel economy, and good starting in cold “Toyota Genuine Motor Oil” is used in weather. your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent If SAE 5W−30 oil is not available, SAE to satisfy the following grade and viscos- 10W−30 oil may be used.
Page 339: Checking The Engine Coolant Level
Toyota engines. Do not use plain water alone. If you can find no leak, have your Toyota Please contact your Toyota dealer for fur- dealer test the cap pressure and check ther details about “Toyota Genuine Motor for leaks in the cooling system.
Page 340: Checking The Radiator And Condenser
If any of the above parts are extremely dirty or you are not sure of their condi- tion, take your vehicle to a Toyota dealer. CAUTION To prevent burning yourself, be care- ful not to touch the radiator or con- denser when the engine is hot.
Page 341: Checking Brake Fluid
Checking brake fluid If the level is low, add SAE J1703 or NOTICE FMVSS No. 116 DOT 3 brake fluid to the brake reservoir. Only use the Suspension fluid AHC for the active height control suspen- Refilling brake fluid: sion. If you fill other fluids such as 1.
Page 342: Checking Power Steering Fluid
Checking power steering fluid Clean all dirt from outside of the reservoir NOTICE tank and look at the fluid level. If the fluid is cold, the level should be in the “COLD” If you spill some of the fluid, be sure If cold If hot range.
Page 343: Checking Tire Inflation Pressure
Checking tire inflation pres- sure CAUTION The reservoir may be hot so be care- ful not to burn yourself. NOTICE Avoid overfilling, or the power steer- ing could be damaged. 72c502b Type A Type B...
Page 344 Keep your tire inflation pressures D Always use a tire inflation pres- Tire inflation at the proper level. sure gauge. The appearance of pressure gauge a tire can be misleading. Besides, The recommended cold tire inflation tire inflation pressures that are pressures, tire sizes and the com- even just a few pounds off can de- bined weight of occupants and cargo...
Page 345 D A greater possibility of tire waste fuel, reduce the comfort of driv- damage from road hazards ing, reduce tire life and make your ve- hicle less safe to drive. If a tire frequently needs refilling, have it checked by your Toyota deal-...
Page 346: Checking And Replacing Tires
Checking and replacing tires The tires on your Toyota have built−in If air loss occurs while driving, do not Tread wear indicator tread wear indicators to help you continue driving. Driving even a short know when the tires need replace- distance can damage a tire beyond ment.
Page 347 Using any other size or type of tire Toyota recommends all four tires, CAUTION may seriously affect handling, ride, or at least both front or rear tires speedometer/odometer calibration, be replaced as a set. Observe the following instruc- ground clearance, and clearance be- See “If you have a flat tire”...
Page 348: Rotating Tires
To equalize tire wear and help ex- Do not use tires other than those men- tend tire life, Toyota recommends tioned above. Do not install studded tires that you rotate your tires accord- without first checking local regulations for ing to the maintenance schedule.
Page 349 SNOW TIRE INSTALLATION CAUTION Side chain Snow tires should be installed on all wheels. Observe following instructions. Installing snow tires on the rear wheels Otherwise, an accident may occur re- only can lead to an excessive difference sulting in death or serious injuries. in road grip capability between the front Do not use snow tires other than and rear tires which could cause loss of...
Page 350: Replacing Wheels
When installing chains on your tires, care- Correct replacement wheels are available When driving with chains installed, fully follow the instructions of the chain at your Toyota dealer. be sure to drive carefully. Slow manufacturer. down before...
Page 351: Aluminum Wheel Precautions
Otherwise, an accident may occur re- sulting in death or serious injuries. When balancing your wheels, use only Toyota balance weights or equivalent Do not use wheels other than the and a plastic or rubber hammer. manufacturer’s recommended size,...
Page 352 SECTION − DO-IT-YOURSELF MAINTENANCE Electrical components Checking battery condition ........Battery recharging precautions .
Page 353: Checking Battery Condition
Checking battery condition— —Precautions —Checking battery exterior CAUTION If electrolyte gets on your skin, Ground cable Terminals thoroughly wash the contact area. If BATTERY PRECAUTIONS you feel pain or burning, get medi- cal attention immediately. The battery produces flammable and explosive hydrogen gas.
Page 354: Battery Recharging Precautions
To return the moon roof to normal, Have battery Dark White see “Electric moon roof” on page 31. checked by your NOTICE Toyota dealer. Never recharge the battery while the Clear or Have battery engine is running. Also, be sure all light checked by your accessories are turned off.
Page 355: Checking And Replacing Fuses
Checking and replacing fuses Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration. Type A If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good.
Page 356: Adding Washer Fluid
Add washer gain access to the bulbs. When replacing tem. Have your Toyota dealer correct it as fluid. a bulb, make sure the ignition switch and soon as possible.
Page 357 Hold a bulb pooled inside light, contact your only by its plastic or metal case. Interior lights — Toyota dealer. Do not touch the glass part of a Personal lights bulb with bare hands. Type A — Bulb Light bulbs Type Type B —...
Page 358 —Headlights 73c005a 1. Open the hood. 2. Left−hand headlight and right−hand 3. Pull the bulb out of the bulb base. head light (high beam): Left−hand headlight: Remove If the connector is tight, wiggle it. Turn the bulb base counterclockwise washer inlet. to the front of the vehicle.
Page 359 Right−hand headlight (low beam): Install the bulb base by turning it counterclockwise to the front of the vehicle. Left−hand headlight: Remove washer inlet. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.
Page 360 Use a flathead screwdriver. 3. Install a new bulb base by turning it clockwise to the front of the vehicle. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.
Page 361 —License plate lights a: Rear turn signal light b: Back–up light...
Page 362: Specifications
SECTION SPECIFICATIONS Specifications Dimensions and weightss ........Engine .
Page 363: Dimensions And Weightss
Dimensions and weights Engine Fuel Overall length mm (in.) 4890 (192.5) Model: Fuel type: 4.7L V8 (2UZ−FE) Unleaded gasoline, Octane Rating 87 Overall width mm (in.) 1940 (76.4) (Research Octane Number 91) or higher. Type: ∗ 1 Overall height mm (in.) 1875 (73.8) 8 cylinder V type, 4 cycle, gasoline Fuel tank capacity, L (gal., Imp.gal.):...
Page 364: Service Specifications
Coolant type: DENSO SK20R11 “Toyota Super Long Life Coolant” is used IFR6A11 in your Toyota vehicle at factory fill. In Spark plug gap, mm (in.): order to avoid technical problems, only use 1.1 (0.043) “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−sili-...
Page 365 No.2 or Molybdenum—disulfide lithium Hypoid gear oil API GL−5 changing automatic transmission base chassis grease, NLGI No.2 fluid, use only “Toyota Genuine ATF Recommended oil viscosity: WS” (ATF JWS3324 or NWS9638) to aid Above –18_C (0_F) in assuring maximum transmission per- SAE 90 formance.
Page 366 BRAKES Minimum pedal clearance when depressed with the force of 490 N (50 kgf, 110 lbf) with the engine running, mm (in.): 116 (4.6) Pedal free play, mm (in.): 1 – 6 (0.04 – 0.24) Pad wear limit, mm (in.): 1.0 (0.04) Lining wear limit, mm (in.): 1.0 (0.04)
Page 367: Tires
Tires Tire size and inflation pressure: kPa (psi) Front Rear Spare Tire size Wheel size Normal Trailer Normal Trailer Normal Trailer driving towing driving towing driving towing 220 (32) 240 (35) P275/60R18 111H 200 (29) 220 (32) 220 (32) 240 (35) Wheel nut torque, N·m (kgf·m, ft·lbf): 131 (13.4, 96.6) NOTE: For complete information on tires (e.g.
Page 368: Fuses
Fuses Engine compartment Left side kick panel Right side kick panel Fuses 8. HAZ−TRN 15 A: 18. BAT 30 A: Emergency flashers, All components in “ECU−B2” Turn signal lights 1. ABS NO.2 40 A: Anti−lock brake sys- 19. TEL 7.5 A: No circuit 9.
Page 369 34. AHC−B 15 A: Active height control sus- 52. DIFF 20 A: Four−wheel drive system pension (AHC) 53. WASHER 15 A: Windshield washer 35. FUEL HTR 20 A: Fuel heater 54. RADIO 10 A: Audio system 36. POWER HTR 7.5 A: Power heater 55.
Page 370 70. RR A/C 30 A: Rear air conditioning system 71. RH SEAT 30 A: Power seat system 72. AIR PUMP 50A: Multiport fuel injection system/Sequential multiport fuel injec- tion system 73. A/F HTR 15A: Multiport fuel injection system/Sequential multiport fuel injec- tion system...
Page 372 SECTION REPORTING SAFETY DEFECTS FOR U.S. OWNERS AND UNIFORM TIRE QUALITY GRADING Reporting safety defects for U.S. owners and uniform tire quality grading Reporting safety defects for U.S. ownerss ....
Page 373 However, NHTSA cannot become involved in individual prob- lems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc.

Toyota 2007 Land Cruiser Owner's Manual

1 2 Section −

1 3 Section −

1 4 Section −

1 5 Section −

1 6 Section −

1 7 Section −

1 8 Section −

1 9 Section −

1 10 Section −

2 Section

3 Section

4 Section

6 Section

7 1 Section −

Quick Links

Chapters

Related Manuals for Toyota 2007 Land Cruiser

Summary of Contents for Toyota 2007 Land Cruiser