Mongoose MX40 II Series Operating & Installation Instructions Manual

Hide thumbs Also See for MX40 II Series:

Advertisement

THE REC OGNISED NAME IN SECURITY
MX40 Series II
STANDARDS CERTIFIED AS/NZS4601 1999 amendment 1 2003
OPERATING & INSTALLATION INSTRUCTIONS
DO NOT LEAVE THIS MANUAL IN YOUR VEHICLE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MX40 II Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Mongoose MX40 II Series

  • Page 1 THE REC OGNISED NAME IN SECURITY MX40 Series II STANDARDS CERTIFIED AS/NZS4601 1999 amendment 1 2003 OPERATING & INSTALLATION INSTRUCTIONS DO NOT LEAVE THIS MANUAL IN YOUR VEHICLE...
  • Page 2: Remote Security

    MX40II REMOTE SECURITY BUTTON ONE ONLY BUTTON TWO ONLY ‘ARM’ (& LOCK) ‘DISARM’ (& UNLOCK) PRESS FOR 1.5 SECONDS PRESS BUTTON TWO TO TO ARM THE SECURITY SYSTEM - DISARM THE ALARM SYST EM. (DOORS WILL ALSO LOCK IF THE (DOORS WILL ALSO UNLOCK CENTRAL LOCKING HAS BEEN IF THE CENTRAL LOCKING...
  • Page 3 ARMING THE SYSTE M - BY REMOTE The sy stem is armed by depressing button ONE on the remote control momentarily (approx. 1~1.5 seconds). Y ou will notice the park lights will flash once to indicate that the sy stem is armed. (The optional siren will chirp once) The dash board warning light, LED, will slow f lash to indicate armed mode.
  • Page 4: Auto Matic Re-Set

    SECURITY RE-ARM (& RE-LOCK) The sy stem will automatically re-immobilise after 30 seconds if it has been disarmed by remote. Doors will also re-lock, if connected, if no door is opened within the 30 seconds. Opening a door will not prev ent the engine f rom being automatically immobilised – the engine must be started to prevent this.
  • Page 5 P ARK LIGHT CONFIRMATION / CODES This is a v isual indication of system status. 1 Flash - Armed by remote. 2 Flashes - Disarmed. 3 Flashes - Armed by remote with a door left open. 4 Flashes - Disarmed but system was triggered. Flashes f or 30 seconds - System triggered.
  • Page 6 FACTORY PRE- SET CODE IS 1-1-1-1 SYSTEM OVERRIDE – PIN CODED Should the remote control fail to operate the system or is lost, the system can be overridden using a unique 4 digit PIN code of your choice. Y ou can change the PIN code at any time when the system is disarmed and how to do this is detailed later in this manual.
  • Page 7 Mongoose dealer. WHAT HAPPENS IF I FORGET MY PIN CODE NUMBER ? Providing your remote controls are in working order, you can re-programme a new PIN or, visit an authorised Mongoose dealer who can re-programme a unique number for you.
  • Page 8 If you cannot recall the PIN code, please call your local Mongoose direct during normal office hours. You will need to provide evidence that you are the vehicle owner and the serial number of the security system.
  • Page 9: Installation

    Inspect and identify all components of the supplied equipment. The supply of installation tools or equipment is not included. Carry out a v ehicle inspection report as shown in the general Mongoose installation manual Disconnect the v ehicle battery & disable any airbag.
  • Page 10 COMPONENT LOCATION SIREN ASSEMBLY (OPTION AL PART) Select a suitable location f or the siren assembly under the bonnet, away f rom sources of extreme heat and possible water damage. Select a location that will allow a direct sound path towards the ground for maximum sound dispersion.
  • Page 12 WIRING DO NOT CONNECT THE MAIN +12V POWER SUPPLY PRIOR TO WIRING AND SOLDERING THE OTHER CONNECTIONS. SIREN ASSEMBLY (OPTION AL – NOT SUPPLIED) Secure a ring terminal on the black wire of the siren to chassis (ground). Use a serrated washer and screw to ensure a good grounding.
  • Page 13: Main Module

    MAIN MODULE The main module has concealed plugs with only black wires emitting from it. The wires are labeled for the f unction; (+) 12V OUTPUT TO PARKING LIGHTS DOOR TRIGGER (‘+’ OR ‘-‘ SELECTABLE BY JUMPER J5. FACTORY SET TO ‘-‘) (-) NEGATIVE GROUND (+) 12V FUSED CONSTANT POWER (+) 12V IGNITION INPUT WIRE (ALSO +12V BACK-UP FOR IMMOBILISATION)
  • Page 14 GROUND – 2 WIRES (-) Two ground (-) wires are prov ided, connect these v ia ring terminals to two separate ground points ensuring a good metal to metal contact. Do not connect the ground wires together. IMMOBILISER WIRES – EACH 15AMP CONTINUOUS There are 2 automatic engine immobiliser circuits.
  • Page 15: Ignition Wire

    The MX40II has low current lock and unlock central locking outputs. Additional components may be required depending on the ty pe of v ehicle and/or its’ central locking. Please refer to the Mongoose installation manual f or f urther details.
  • Page 16 OVERRIDE PIN CODE PROGRAMMING The factory default is 1-1-1-1 The PIN code is programmable to any 4 digit number. . This must be changed to a number the v ehicle owner can easily remember. It is recommended that installers do not keep any record of the v ehicle owners PIN code.
  • Page 17: Completing The Installation

    TESTING SYSTE M OPERATION Af ter all the connections have been made and checked f or correct connection, re-connect the battery. If the parking lights flash press Button ONE on the remote control to cancel. Now follow the operator instructions and test all features COMPLETING THE INSTALLATION Once all the testing procedures f or the system hav e been carried out and are satisf actory, secure the main module to the predetermined area under the dash.
  • Page 18 THE RECOGNISED NAME IN SECURITY Mongoose (Australia) Pty Lim ited Sydney, Melbourne, Brisbane Mongoose (New Zealand) Lim ited Auckland For service contact your Mongoose agent;...

Table of Contents