Table of Contents
Advertisement
"That's a name you can trust"
M60 Series
M60i, M60B, M60S, M60AU, M60AM
MODELS:
OPERATION & WIRING MANUAL
All models certified to:-
AS/NZS4601 1999 amendment 1 2003
& AS/NZS3749.1 2003 Class B
.
These products should be installed according to the
requirements of the AS/NZS 3749.2 Installation Standard
References to alarm functions and siren responses do not apply to model M60i
Advertisement
Table of Contents
Related Manuals for Mongoose M60i
Summary of Contents for Mongoose M60i
- Page 1 All models certified to:- AS/NZS4601 1999 amendment 1 2003 & AS/NZS3749.1 2003 Class B These products should be installed according to the requirements of the AS/NZS 3749.2 Installation Standard References to alarm functions and siren responses do not apply to model M60i...
- Page 2 PRESS FOR 3 SECONDS TO SOUND THE SIREN OF THE ALARM. PRESS BOTH AGAIN TO CANCEL BATTERY REPLACEMENT YOUR REMOTE CONTROL USES ONE 12v 23amp BATTERY WHICH IS AVAILABLE FROM YOUR MONGOOSE AGENT OR ELECTRONIC SHOP. CHANGE AT LEAST ONCE A YEAR.
-
Page 3: Table Of Contents
CONTENTS Automatic engine immobilisation.. Indicator flashing……………… 10 Arming………… ……....Dash mounted warning light… 10 Open circuit bypass….…………… Chirp confirmation…....Central locking..…....… .. Panic…………..…..….. 11 Disarming…………………………. Boot release…………..…... 11 Security re-arm……………….….. Programme options..…... 11/12 Silent arm/disarm ……………….… * Siren or horn output Bonnet, boot &... -
Page 4: Automatic Engine Immobilisation
PERATING YOUR VEHICLE SECURITY SYSTEM AUTOMATIC ‘DUAL CIRCUIT’ ENGINE IMMOBILISATION The engine will always be automatically immobilised 30 seconds after the ignition has been turned off. This feature cannot be turned off or defeated as it is a Standards mandatory feature. When the ignition is turned OFF, the dashboard LED will start to fast flash for 30 seconds to indicate the automatic sequence has commenced. -
Page 5: Arming
ARMING NORMAL OPERATION Turn the engine off, close all windows and remove the keys from the ignition Exit the vehicle and close all the doors (& bonnet & boot). Press button one on the remote control. The indicators flash once and the siren will chirp once to indicate that the system is armed. The dash board warning light, LED, will slow flash to indicate the system is armed. -
Page 6: Disarming
DISARMING Press button one on the remote control to disarm the system. The siren will chirp twice and the indicators will flash twice to indicate disarming. The doors will unlock if the vehicles’ central locking is connected to the security system. ... -
Page 7: Stage Impact Sensor (M60B) 7 Ultrasonic Sensors (M60Au)
2 STAGE IMPACT SENSOR (MODEL M60B/M60S – optional on other models) This sensor is designed to detect impact to the vehicle such as to the bodywork or glass. It should not be triggered by normal wind, or rocking motions. If the sensor detects a light impact, the siren will sound a few warning chirps. ... -
Page 8: Microwave Sensor (M60Am)
MICROWAVE SENSOR (M60AM MODEL – optional on other models) The microwave sensor is designed to trigger the alarm when a microwave field registers physical movement. 2 fields are generated, one outside the vehicle to give perimeter protection, and one inside to give interior protection. Intrusion into the perimeter area chirps the siren as a warning, whilst intrusion into the interior fully sounds the siren. -
Page 9: Battery Back-Up Siren (M60Au/Am)
BATTERY BACK-UP SIREN (M60S/M60AU/M60AM – optional on other models) Vehicle battery disconnection, or cutting the siren wires, will cause the battery back-up siren to sound independently of an alarm trigger. The siren can be turned off with the special keys provided or whenever the car battery needs attention or changing. -
Page 10: Indicator Flashing
INDICATOR FLASHING (FUSE PROTECTED) When the siren sounds, the indicators flash simultaneously. The indicators will also flash on arming and disarming the system. 1 Flash - Armed. 2 Flash - Disarmed. 3 Flash - Disarmed and previously triggered. DASH MOUNTED WARNING LIGHT – LED The LED shows the status of the alarm, intrusion and any open circuit when arming. -
Page 11: Panic
PANIC BY REMOTE (in either armed or disarmed state) In the event of personal attack, or you suspect that your vehicle is being tampered with, the alarm can be ‘panicked’ by pressing buttons one and two at the same time on the remote for more than 3 seconds. - Page 12 PROGRAMME OPTIONS EXPLAINED AUTOMATIC (LAST DOOR) ARMING - PROGRAMMABLE This feature is factory set in the ‘off’ position. You may have this programmed ‘on’ for added security. The alarm will arm automatically 30 seconds after the last door is closed. The doors will not lock so that keys cannot be locked inside ...
-
Page 13: Remote Controls
An irregular or interruption to the vehicle’s power supply may cause loss of remote memory. If your alarm fails to respond to the remote try re-learning them or see your Mongoose dealer. - Page 14 REMOTE ‘CODE LEARNING’: To learn a remote or additional remote: Disarm the system Open the drivers door and leave open Turn the ignition ON/OFF 3 times (ignition remains off) The siren will chirp 3 times, the indicators will flash 3 times and the dashboard LED will ...
-
Page 15: Emergency Override
MONGOOSE EMERGENCY EMERGENCY OVERRIDE – 4 DIGIT PIN CODED 4 DIGIT PIN CODE OVERRIDE The system can be disarmed by entering your the unique 4 digit PIN PIN CODE: code shown on the ‘PIN Code Card’ issued with this product. -
Page 16: Testing Your Alarm
1) Without disarming the system, unlock and open a door with the ignition key - the alarm should sound, excluding model M60i. Check all other doors, bonnet and boot by the same procedure. 2) Check the impact sensor, M60B only unless fitted as an accessory, by giving the vehicle varying degrees of impact - be careful to do this on areas of the vehicle not likely to be damaged by impact. - Page 17 WIRING INFORMATION: Installation to be carried out by suitably qualified persons. MAIN MODULE The plugs are edge numbered & the wires printed for the function; – TRIG (-) BONNET & BOOT TRIGGER INPUT (-) CH 2 OUTPUT – EG: BOOT RELEASE (+) 12v IGNITION INPUT GND ARM GROUND WHEN ARMED...
- Page 18 WIRING...
- Page 19 TURBO INTERFACE To enable, remove the cover from the main module and remove the jumper between the main IC and the receiver board. SENSOR PORT The sensor port is a 4 pin input that accepts an impact sensor, ultrasonic sensor or microwave sensor.
- Page 20 IMPACT SENSOR – Included in M60B/M60S – optional on other models. The impact sensor is 2 stage:- light impacts should chirp the siren, whilst heavier impacts should fully sound the siren. The sensor should not be mounted in the engine compartment. The ideal location for this sensor is solidly mounted under the dashboard near the centre of the vehicle.
- Page 21 Do not adjust interior field greater than exterior. The ‘noise pollution control’ feature will turn off each trigger input after 3 intrusions into each. Reset by remote to re-activate the sensor. Full installation instructions are available on the Mongoose internet site: www.mongoose.com.au...
- Page 22 Mongoose warrants for a period of 36 months that it will make good without charge at Mongoose’s discretion, by repair or replacement with a reasonable equivalent, any defect in the product providing that; (a) the defect has been notified as soon as it is noticed to an authorised Mongoose installation centre, distributor or agent (in the first instance to the original installation centre).
- Page 23 Whilst this security system provides a deterrent, it may not prevent theft or damage through wilful criminal intent. Mongoose does not by inference, intent or any other means guarantee that a vehicle fitted with one of it’s security systems will not be stolen, broken into, tampered with, or parts taken.
- Page 25 Please complete the above details, detach from this manual and keep in a safe place. These details should be presented to your Mongoose dealer in the unlikely event that you require this product to be repaired under the terms of the ‘product warranty’.