Editing Clip Lists; Basic Operations; Reordering Sub Clips - Sony PDW-F30 Operating Instructions Manual

Editing Clip Lists

You can select items from CLIP menus, and perform
simple editing operations on clip lists and on sub clips
registered in clip lists.

Basic Operations

TCG
0 0
E X T
- 1 2 - 1 2
- 2 0 - 2 0 TC MODE
P R E S E T
- 3 0 - 3 0
ACCESS - 4 0 - 4 0
RUN MODE
- 6 0 - 6 0
REC RUN
1 2 3 4
3 + 4
4 CH 16 BIT T C / V I T C
NETWORK
V I T C
MPEG HD SP 1080 60I
LOCAL
VITC COOO1 REM:077 M
D F / N D F
00: 00.00: 00 NDF
REMOTE
P2
LEVEL
CH 1 CH 2 CH 3 CH 4
PHONES
1
In the clip list screen, hold down the MENU button.
The CLIP menu appears.
2
Press the M/MARK1 or m/MARK2 button to select
the edit item you want.
You can carry out the following edit operations.
CLIP menu Item
MOVE
TRIM
DELETE
TC PRESET
3
Press the SET button.
A screen appears to allow you to select the target sub
clip of the operation. (A timecode setting screen
appears if you have selected TC PRESET.)
4
Use the arrow buttons or jog dial to select the desired
sub clip.
62
Editing Clip Lists
1 3,5 2,4
F1
F2
F3
VAR
MARK1
MENU
F4
CHAPTER
SUB THUMB IN OUT
EXPAND
F5
CLIP NAIL SET RESET
JOG
PAGE DISPLAY
CLIP ESSENCE
MENU MARK MARK2
PREV PLAY NEXT STOP TS REC
SHUTTLE
KEY INHI
PRESET
PB
SHIFT
TOP F REV F FWD END STANDBY
4 4
Description
Reorder sub clips.
Change the In and Out points of
sub clips.
Delete unnecessary sub clips.
Set the first timecode of the
current clip list to any value.
You can also select clips with the following
operations.
Press the PREV or NEXT button: Moves to the
previous or next clip.
Press the PREV or NEXT button with the SHIFT
button held down: Moves to the first or last clip.
Press M/MARK1 or m/MARK2 button with the
SHIFT button held down: Switches to the
previous or next page. Does not switch when
there is only one page.
Press an </IN button or ,/OUT button with the
SHIFT button held down: Selects continuous
multiple clips.
Note
EJECT
If you selected "TRIM", you can select only one sub
clip.
5
Press the SET button.
This allows you to carry out the editing operation
selected from the CLIP menu for the selected sub clip.
6
Carry out the selected editing operation.
For details, see the following pages.
Reordering sub clips: Page 62
Trimming sub clips: Page 63
Deleting sub clips: Page 64
Setting the timecode: Page 64
7
Save the edited current clip list to disc.
For details, see "Saving the Current Clip List to Disc"
(page 65).

Reordering Sub Clips

Proceed as follows.
1
Carry out steps 1 to 5 of the procedure in "Basic
Operations" (see page 62) (select "MOVE" in step 2).
The I-shaped cursor indicating the move destination
appears in the clip list window.
2
Use the arrow buttons or jog dial to move the I-shaped
cursor to the desired position.
You can also move the cursor with the following
operations.
Press the PREV or NEXT button: Moves the cursor
to the previous or next sub clip.
Press the PREV or NEXT button with the SHIFT
button held down: Moves the cursor to the first
or last sub clip.
Press M/MARK1 or m/MARK2 button with the
SHIFT button held down: Switches to the