Table of Contents
Advertisement
5 Takeover indicator
6 AUTO BEAT LOOP button
Turns the auto beat loop function on and off.
[SHIFT] + press:
Switches the loop saved in the track between active and non-active.
(Active Loop)
7 LOOP 1/2X button
Halves the loop playback length.
[SHIFT] + press:
During loop playback, moves the loop to the left by the amount equal
to its length. (Loop Move)
8 LOOP 2X button
Doubles the loop playback length.
[SHIFT] + press:
During loop playback, moves the loop to the right by the amount
equal to its length. (Loop Move)
9 LOOP IN button
Loop In Point is set.
[SHIFT] + press:
The track returns to the set loop in point and loop playback
continues.
Press for over 1 second:
Turns the auto 4-beat loop on.
a LOOP OUT button
The loop out point is set, and loop playback begins.
[SHIFT] + press:
Cancels loop playback. (Loop Exit)
After loop playback is canceled, playback returns to the previously
set loop in point and loop playback resumes. (Reloop)
b CAPTURE button
Press a performance pad while pressing the [CAPTURE] button to
load the active loop to the sampler slot.
[SHIFT] + press:
Loads the sections in the target area of slicer or slicer loop to sepa-
rate sampler slots.
! For detailed instructions on slicer and slicer loop, see the rekord-
box software's manual.
c SEQUENCER OVERDUB button
Press:
Turns the sequencer on standby for recording.
Recording operation information (sequence) is started if the sampler
is operated when the sequencer is on standby for recording. Press
the button again to stop recording.
[SHIFT] + press:
Saves the recorded sequence to the sequencer slot.
d SEQUENCER START button
Starts the sequence playback when the sequence recording is
stopped.
Overdubs the new sequence onto the sequence being played back
while recording a sequence.
[SHIFT] + press:
Selects the sequencer slot.
e HOT CUE mode button
Sets the hot cue mode.
[SHIFT] + press:
Sets the beat jump mode.
6
En
f PAD FX1 mode button
Sets the pad FX mode 1.
[SHIFT] + press:
Sets the pad FX mode 2.
g SLICER mode button
Sets the slicer mode.
[SHIFT] + press:
Sets the slicer loop mode.
h SAMPLER mode button
Sets the sampler mode.
[SHIFT] + press:
Sets the velocity sampler mode.
i Performance pads
Controls the "hot cue", "pad FX", "slicer", "sampler" and other
functions.
j PARAMETERc button, PARAMETERd button
Sets parameters for the "pad FX", "slicer", "sampler" and other
functions.
k PLAY/PAUSE f button
Use this to play/pause tracks.
l CUE button
Sets, plays and calls out cue points.
[SHIFT] + press:
Returns the playback position to the beginning of the track.
m SYNC button
Synchronizes with the tempos (pitches) and beat grids of the deck
set as the master for synchronization automatically.
[SHIFT] + press:
Sets the deck whose button is pressed as the master deck for
synchronization.
n SHIFT button
When another button is pressed while pressing the [SHIFT] button, a
different function is called out.
! For details on operation using the [SHIFT] button, see the
Operating Instructions.
o DECK button
Switches the deck to be operated.
Pressing the [DECK3] button while holding down the [DECK1] but-
ton or pressing the [DECK1] button while holding down the [DECK3]
button:
Turns on DUAL DECK mode on the left deck.
Pressing the [DECK4] button while holding down the [DECK2] but-
ton or pressing the [DECK2] button while holding down the [DECK4]
button:
Turns on DUAL DECK mode on the right deck.
p GRID ADJUST button
When the jog dial is turned while pressing the [GRID ADJUST] but-
ton, the beat grid interval can be adjusted.
[SHIFT] + press:
The BPM value is divided by 1/2 (doubling the beat grid's spacing).
q GRID SLIDE button
When the jog dial is turned while pressing the [GRID SLIDE] button,
the overall beat grid can be slid to the left or right.
[SHIFT] + press:
The BPM value is multiplied by 2 (reducing the beat grid's spacing
by 1/2).
Advertisement
Table of Contents
