DSC PC5020 Power864 Installation Manual page 51

Hide thumbs Also See for PC5020 Power864:

User manual (13 pages)

Table Of Contents

Table of Contents

Placement Indication

After the zone is selected, the alarm contacts must be

opened. This will register a signal strength value that will

be indicated and anunciated on all keypads, as well as on

the bell. The system will remain in this test mode until [#]

is pressed or Installer Time-out (20 minutes).

• GOOD signal will be indicated by Light 1 on an LED

keypad or the word GOOD on an LCD keypad. It will be

enunciated on the Keypad by 1 beep and on the Bell by 1

Squawk.

• FAIR signal will be indicated by Light 2 on an LED key-

pad or the word FAIR on an LCD keypad. It will be

enunciated on the Keypad by 2 beep and on the Bell by 2

Squawk.

• BAD signal will be indicated by Light 3 on an LED key-

pad or the word BAD on an LCD keypad. It will be enun-

ciated on the Keypad by 3 beep and on the Bell by 3

Squawk.

• Non-Enrolled zone will be annunciated on the Keypad

by an error tone.

[906] - Local Downlook Remote Trigger

While in this section, either 1 or 2 can be pressed to ini-

tiate Downlook to either phone number 1 or 2, respec-

tively. The panel will communicate the System Test event,

log 'Downlook Remote Trigger', and transmit the script

found in the PC5108L for Remote Trigger.

[990][Installer Code] - Installer Lockout Enable

If enabled, the panel will give a distinctive audible indica-

tion on power up (the phone line relay will click 10

times). This feature will have no effect on a Software

Default (all programming will return to the factory

defaults). However, if a Hardware default is attempted

while lockout is enabled, the default will not occur, and

the fraudulent attempt will be logged to the event buffer.

Installer Lockout

If Installer Lockout is selected a hardware default cannot

be performed. If a software default is performed all pro-

gramming will restore to factory default.

When Installer Lockout Disable is selected the panel will

restore all programming to factory defaults if a hardware

or software default is performed on the main control panel.

To enable Installer Lockout perform the following:

1.Enter Installer Programming.

2.To enable Installer Lockout, enter section [990]

3.Enter the Installer Code.

4.Enter section [990] again.

[991][Installer Code] - Installer Lockout Disable

This disables the Installer Lockout feature described above.

To disable Installer Lockout perform the following:

1. Enter Installer Programming.

2. To disable Installer Lockout, enter section [991].

3. Enter the Installer Code.

4. Enter section [991] again.

[993]-[999] Factory Defaults

On occasion it may be necessary to default the main con-

trol panel or one of the modules that can be connected.

There are several different defaults available including

defaulting the main control panel, Escort5580(TC) mod-

ule, PC5132 wireless expander module, PC5400 printer

module and LINKS2X50 module.

NOTE: Defaulting the main panel does not default the

keypads. See the Programming Worksheets Appendices

A and B for instructions for defaulting LCD5500Z/

LCD5501Z keypads. PC55XXZ LED keypads must be

manually reprogrammed in programming section [000].

P r o g r a m m i n g S e c t i o n s : 5 . 1 1 S p e c i a l I n s t a l l e r I n s t r u c t i o n s P W S S e c t 1 1

Factory Default Main Panel (Hardware)

1. Remove AC and battery power from the panel.

2. Remove all wires from the zone 1 and PGM1 terminals.

3. With a piece of wire short the zone 1 terminal to the

PGM1 terminal.

4. Apply AC power to the main panel.

5. When zone light 1 is lit on the keypad the default is com-

plete.

6. Remove AC power from the control

7. Reconnect all original wiring and power up the control.

NOTE: AC power must be used to power the panel.

The panel will not default if the battery is used.

Factory Default Main Panel (Software) and other

modules

1. Enter Installer Programming.

2. Enter the appropriate programming section [99X].

3. Enter the Installer Code.

4. Enter the appropriate programming section [99X] again.

The panel will take a few seconds to reset. When the key-

pad is operational, the default is complete.

[993][Installer Code] - Restore Alternate Comm.

Factory Default Programming