Table of Contents
Advertisement
End of Line Resistors . . . . . . . . . . . . . . . . Section [013], Option [1]
Single End of Line Resistors . . . . . . . . . . . Section [013], Option [2]
Double End of Line (DEOL) Resistors
Double end of line resistors allow the panel to determine
if the zone is in alarm, tampered or faulted.
To enable panel detection of double end-of-line resistors,
programming section [013], option [1] must be OFF and
option [2] must be ON.
NOTE: If the double EOL supervision option is
enabled, all hardwired zones must be wired for double
EOL resistors, except for Fire and 24-hr Supervisory
zones.
Do not wire DEOL resistors on keypad zones.
Do not use DEOL resistors for Fire zones or 24-hr
Supervisory zones. Do not wire Fire zones to keypad
zone terminals if the DEOL supervision option is
selected.
This option can only be selected if Normally Closed
(NC) detection devices or contacts are being used. Only
one NC contact can be connected to each zone.
The following chart shows zone status under certain con-
ditions:
Loop Resistance
0Ω (shorted wire, loop shorted)
5600Ω (contact closed)
Infinite (broken wire, loop open)
11200Ω (contact open)
End-of-Line Resistors . . . . . . . . . . . . . . . . Section [013], Option [1]
Double End-of-Line Resistors . . . . . . . . . . Section [013], Option [2]
Fire Zone Wiring - 4-wire Smoke Detectors
All zones defined as Fire (see section 'Basic Programming
PWS Sect 3') must be wired according to the following
diagram:
Loop Status
Fault
Secure
Tamper
Violated
9
I n s t a l l a t i o n a n d W i r i n g : 2 . 1 0 Z o n e W i r i n g
For a complete description of how fire zones operate, see
section 'Basic Programming PWS Sect 3'.
Fire Zone Wiring - 2-wire Smoke Detectors
If PGM2 has been programmed for 2-wire smoke detector
connection (see section 'Basic Programming PWS Sect 3'),
the detectors must be wired according to the following
diagram:
NOTE: If PGM2 is programmed for 2-wire smoke sup-
port, Jumper CON1 on the main board must be
removed.
For a complete description of how fire zones operate, see
section 'Basic Programming PWS Sect 3'.
Keyswitch Zone Wiring
Zones may be programmed to be used as keyswitch arm-
ing zones and must be wired according to the following
diagram:
For a complete description of how keyswitch zones oper-
ate, see section 'Basic Programming PWS Sect 3'.
LINKS1000 Supervisory (24-hr Supervisory)
When using the LINKS1000 cellular communicator, any
main board zone may be configured for LINKS1000 Super-
vision. Program this zone as zone type (09), 24-hr Supervi-
sory in section [001].
With a 24-hr Supervisory zone, if the LINKS1000 experi-
ences a trouble, the zone will be violated, causing the
panel to report the event to the central station. This type
of
zone
always
requires
(5600Ω).Refer to LINKS 1000 Installation Manual wiring
diagram for installation.
LINKS1000 Answer
If the LINKS1000 cellular commu-
nicator is being used a zone may
be
configured
Answer to allow downloading to
be performed in the event of tele-
phone line failure. When the
LINKS1000 receives a telephone
call it will activate the RING termi-
nal on the LINKS1000 circuit board. This terminal can be
used to violate a zone programmed as (24) LINKS1000
Answer (see section 'Basic Programming PWS Sect 3'),
causing the panel to seize the telephone line and begin
communication with the downloading computer.
The zone programmed as LINKS1000 Answer ALWAYS
requires a single EOL resistor (5600Ω) and must be wired
according to the diagram above.
NOTE: The LINKS1000 Answer zone is only required
for downloading to the panel via the LINKS1000, or
for remotely connecting to the Escort5580(TC) module
via the LINKS1000.
NOTE: When using the LINKS1000, Busy Tone Detec-
tion must not be used.
a
single
EOL
resistor
for
LINKS1000
Hide quick links:
Advertisement
Table of Contents
