Advertisement
Quick Links
Planning the installation
Contents
These installation instructions describe how to install
your Omnilock Wall Mount Unit for models OM500
OM2000 and Wireless. Topics covered include:
Planning the installation...........................................1
Installing outside escutcheon...................................4
Troubleshooting..........................................................8
Environment information
Side of
Model
door
Standard
Outside
Weatherized
Outside
Outside
Extreme
a
Weatherized
Inside
a.
See Stanley installation instruction Addendum (T83323)
Extreme Weatherized Installation for the extreme weatherized
model installation.
T83321/Rev A 000000 Jan 2010
Temperature
Exposure
Range
Drip proof.
Inadvertent
+32°F to +129°F
splashing of
0°C to +54°C
water spray
acceptable.
-4°F to +129°F
Direct exposure
-20°C to +54°C
to rain and snow
-40°F to +129°F
Direct exposure
-40°C to + 54°C
to rain and snow
+32°F to +129°F
N/A
0°C to +54°C
a Product Group of Stanley Security Solutions, Inc.
Installation Instructions for
Stanley Omnilock
Wall Mount Units
Components checklist
Use the following checklist to make sure that you
have the items necessary to install your Omnilock
Wall Mount Lock.
Components provided in the box:
❐ Outside escutcheon assembly
❐ Installation template and instructions
❐ Screw package
❐ Wall anchors
❐ Batteries
❐ Cylinder and key
Other components:
❐ Programming Default ID Card (provided with
software)
Remote Switch
Note: Not available for wireless models.
The Omnilock does not come equipped with a
remote switch. However, if the external system has a
remote switch, such as one at a receptionist's desk, it
may be routed through the terminal on the Omnilock
Wall Mount System circuit board. See "Install batter-
ies" on page 3.
Momentarily pressing the switch causes the system
to go through a normal lock and unlock sequence. If
the switch is held closed, the open time will be
extended.
Stanley Omnilock
1
Advertisement
Related Manuals for Stanley Omnilock OM500
Summary of Contents for Stanley Omnilock OM500
- Page 1 Momentarily pressing the switch causes the system to go through a normal lock and unlock sequence. If the switch is held closed, the open time will be extended. Stanley Omnilock T83321/Rev A 000000 Jan 2010 a Product Group of Stanley Security Solutions, Inc.
- Page 2 Installation Instructions for Stanley Omnilock Wall Mount Units Planning the installation Position template and mark drill points Note: When determining the location of the unit, Template take wheel chair access into consideration. 1 Open the template provided Installation Template for Omnilock Wall Mount Units (T83322).
- Page 3 Installation Instructions for Stanley Omnilock Wall Mount Units Installation Instructions for Stanley Omnilock Wall Mount Units Planning the installation Install batteries Housing assembly Four alkaline AA batteries (or two weatherized packs Track setting AA Batteries label if installing a weatherized unit) are furnished with...
- Page 4 Installation Instructions for Stanley Omnilock Wall Mount Units Install outside escutcheon Install outside escutcheon Caution: Since the Wall Mount System controls external circuits, care must be taken to ensure that static electrical discharges will not cause damage to equipment. All devices...
- Page 5 Installation Instructions for Stanley Omnilock Wall Mount Units Installation Instructions for Stanley Omnilock Wall Mount Units Install outside escutcheon Optional: Install Extreme External wiring Weatherized Unit, if necessary Note: Ensure that the external system power Inside wall supply is turned off.
- Page 6 Ground wire #18 AWG (10 MWG) System diagram Fail safe Orange Power supply (24V max) White Wall Fail secure Mount System Black Device (5A max) Green/ Yellow Wire connection diagram Figure 8 Simplified wiring diagrams Stanley Omnilock a Product Group of Stanley Security Solutions, Inc.
- Page 7 Installation Instructions for Stanley Omnilock Wall Mount Units Installation Instructions for Stanley Omnilock Wall Mount Units Install outside escutcheon Install the cylinder assembly 1 With the control key in the core, insert the core into the cylinder assembly. 2 Insert the rear threaded rod of the cylinder assembly into the threaded hole between the mounting screws.
- Page 8 Installation Instructions for Stanley Omnilock Wall Mount Units Troubleshooting Test unit Troubleshooting To test the unit for proper operation before the unit If the mechanism doesn’t unlock, remove the battery is programmed, follow these instructions: cover and check for proper orientation and seating of the batteries and motor connector.