Spray Controls - WAGNER Power Painter Max Owner's Manual

Spray
Controls
Start Notice:
The spray controls vary depending upon the model of
sprayer you have. Refer to this page in order to learn
about the controls of your particular sprayer.
Power Painter Plus
Material Select Lever:
The spray pattern is controlled by the Material Select Lever
on the rear of the sprayer, and by the thickness of the
material being sprayed.
If you are spraying thicker materials such as latex paint, turn
the lever toward the "PAINT" side of the sprayer.
If you are spraying thinner materials such as thinner stains,
turn the lever toward the "STAIN" side of the sprayer.
Note: If you are unable to acheive a good spray pattern
while using the 'STAIN' setting, switch the lever over to
'PAINT'.
PAINT
English
Power Painter Max
Material Select Lever:
Refer to the information given in the previous column.
Electronic Speed Control:
The electronic speed control is displayed by the two
green lights on the right side of the control panel (a).
The Power Painter Max offers two speed levels (LO /
HI). The lower the speed level, the closer you can get to
your work and the less overspray you will have.
Lower speed levels give you greater control but require
more time to cover an area. Depending upon the
thickness of the material or conditions, the settings may
need to be adjusted.
To adjust the speed setting, press the 'SPEED' button
(b) below the speed indicator lights until your desired
speed is reached.
Low Cup Level Indicator
• Applicable only when spraying in cup mode, cup
filled to MAX FILL.
• The low cup level indicator is displayed by the two
red lights on the left of the control panel (c).
When your cup is running out of material, the low cup
level indicators will begin blinking. You should quit
spraying and refill the container (see Cup mode Setup
instructions, page 5). Avoid running the cup dry. An
empty cup will allow air to become sucked into the
sprayer, which leads to globbing and spitting.
Note: Before you resume spraying, press and hold the
'SPEED' button (b) and the indicators will reset and no
longer blink. ALWAYS reset the indicators when the cup
is full and you are ready to resume spraying. Failure
to reset the low cup level indicators will result in the
indicators not functioning properly. The low cup level
lights will reset whenever the power cord is unplugged.
LOW
c
LEVEL
STAIN
HOLD TO RESET LOW LEVEL
Electronic Material Selector:
The spray pattern is controlled by the Electronic Material
Selector (a) and by the thickness of the material.
If you are spraying thicker materials such as latex paint,
press the 'SELECT' button (b) until the indicator light
indicates 'PAINT'.
If you are spraying thinner materials such as thinner stains,
press the 'SELECT' button (b) until the indicator light
indicates 'STAIN'.
Electronic Speed Control:
The speed control is displayed by the three green lights on
the upper right side of the control panel (c).
The Power Painter Pro offers three speed levels (LOW/
MED/HIgH). The lower the speed level, the closer you can
get to your work and the less overspray you will have.
Lower speed levels give you greater control but require more
time to cover an area. Depending upon the thickness of the
material or conditions, the settings may need to be adjusted.
To adjust the speed setting, press the 'SPEED' button
(d) until your desired speed is reached. If the sprayer is
unplugged, the current speed and electronic material selector
setting will be "stored" and remembered during restart.
Low Cup Level Indicator
• Applicable only when spraying in cup mode, cup filled
• The low cup level indicator is displayed by the two red
When your cup is running out of material, the low cup level
indicators will begin blinking. You should quit spraying and
refill the container (see Cup mode Setup instructions, page
5). Avoid running the cup dry. An empty cup will allow
air to become sucked into the sprayer, which leads to
globbing and spitting.
Note: Before you resume spraying, press and hold the
'RESET' button (f) and the indicators will reset and no
longer blink. ALWAYS reset the indicators when the cup
is full and you are ready to resume spraying. Failure to
reset the low cup level indicators will result in the indicators
not functioning properly. The low cup level lights will reset
whenever the power cord is unplugged.
SPEED
a
b
8
Power Painter Pro
to MAx FILL.
lights on the bottom right of the control panel (e).
c
a
b d
f
e