WAGNER POWER PAINTER Owner's Manual
  1. Manuals
  2. Brands
  3. WAGNER Manuals
  4. Paint Sprayer
  5. Power Painter
  6. Owner's manual

WAGNER POWER PAINTER Owner's Manual

The painting people
Hide thumbs Also See for POWER PAINTER:

Advertisement

Table of Contents

See also: Owner's Manual
P
P
OWER
AINTER
•
O
'
M
WNER
S
ANUAL
M
'
ANUEL DE L
UTILISATEUR
M
ANUAL DEL PROPRIETARIO
S
/U
• M
ETUP
SE
1
Read all warnings!
Lire toutes les MISES EN GARDE!
¡Lea todas las ADVERTENCIAS!
+
5
Set flow to maximum
Régler le débit au maximum
Ajuste la salida al nivel máximo
C
• N
LEANUP
ETTOYAGE
1
Return excess material to can
Remettre le produit restant dans le pot
Regrese el exceso de producto a la
lata
5
Remove pump components
Retirer les composants de la pompe
Desarme las piezas de la bomba
Form No. 0285636C
1104 •
The Painting People
™
Read this manual for complete instructions
•
Lire ce manuel contient les instructions complètes
•
Lea este manual para obtener instrucciones completas
/U
ONTAGE
TILISATION
2
Fill the container
Remplir le contenant
Llene el envase
6
Plug in the sprayer
Brancher le pulvérisateur
Enchufe el pulverizador
• L
IMPIEZA
2
Fill with appropriate cleaning solution
Remplir de la solution de nettoyage
appropriée
Llene el envase con la solución de
limpieza apropiada
6
Clean components
Nettoyer les composants
Limpie el las piezas
™
• D
ISPOSICIÓN
3
Attach the suction set
Fixer le dispositif d'aspiration
Conecte la unidad de succión
-
7
Test and adjust spray pattern
Vérifier et régler la forme du jet
Pruebe y ajuste el patrón de rociado
:
3
Spray solution for several seconds
Pulvériser la solution pendant
plusieurs secondes
Rocíe la solución durante varios
segundos
7
Reassemble
Remonter
Vuelva a armar a bomba
Español
/U
:
SO
1
4
Screw on the container
Visser sur le contenant
Enrosque el envase
+
8
Begin spraying
Commencer à pulvériser
Comience a pintar
4
Unplug the sprayer
Débrancher le pulvériser
Desenchufe la pistola
8
Lubricate
Lubrifier
Lubrique
Français
English
2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the POWER PAINTER and is the answer not in the manual?

Questions and answers

sharon rahe
April 13, 2025

How do i remove the paint nosel fo cleaning

0
1 comments:
Mr. Anderson
April 13, 2025

To remove the paint nozzle for cleaning on a Wagner Power Painter:

1. Detach the nozzle tip by popping it off along with the spring.
2. Clean each part individually using lacquer thinner in a small dish.
3. Use a tiny screwdriver or brush to remove paint from threads and small areas.
4. Let parts soak if needed, then scrape off any remaining paint.
5. Reassemble carefully, starting with the ring, then the nozzle tip and spring, and finally reinsert the piston into the gun.

This answer is automatically generated

0
sharon rahe
April 13, 2025

I have an electric wagner hand painter

0

Subscribe to Our Youtube Channel

Related Manuals for WAGNER POWER PAINTER

Summary of Contents for WAGNER POWER PAINTER

  • Page 1 The Painting People ™ ™ OWER AINTER • ’ WNER ANUAL Read this manual for complete instructions ’ • ANUEL DE L UTILISATEUR Lire ce manuel contient les instructions complètes • Lea este manual para obtener instrucciones completas ANUAL DEL PROPRIETARIO •...

  • Page 2: Grounding Instructions

    • Keep sprayer out of the reach of children. • Hearing protection is recommended for extended use. • Use eye protection to keep particles out of eyes. English © 2001 Wagner Spray Tech. All rights reserved.

  • Page 3: Controls And Parts

    NOTE: If you adjust the flow knob and still cannot get could get into the motor housing and damage the sprayer. a good pattern, you may need to thin the material you are using. © 2001 Wagner Spray Tech. All rights reserved. English...

  • Page 4: Material Thinning

    NOTE: When spraying, make sure your fluid container is at least half-filled with material. A container low on fluid will cause the sprayer to spit and will spray a poor pattern. Suction English © 2001 Wagner Spray Tech. All rights reserved.

  • Page 5: Cleaning The Pump Housing

    Never immerse electrical parts in water or any other liquid. Wipe the exterior of the sprayer with a damp cloth for Locking nut cleaning. Always make sure the sprayer is unplugged before taking it apart for cleaning. © 2001 Wagner Spray Tech. All rights reserved. English...

  • Page 6: Lubricating The Sprayer

    The oil protects the sprayer by keeping any extra material from drying and seizing the piston. 5. Replace the suction set and thread the fluid container onto the sprayer. English © 2001 Wagner Spray Tech. All rights reserved.

  • Page 7: Maintenance

    13. Insert the swirl valve into the front end of the pump housing. 14. Place the spray tip onto the pump housing and turn it clockwise until it is tightened securely. © 2001 Wagner Spray Tech. All rights reserved. English...

  • Page 8: Troubleshooting

    (for example, T087R). The additional information will also described in this manual, take your sprayer to the nearest help us to develop new products that best meet your needs and authorized service center. desires. English © 2001 Wagner Spray Tech. All rights reserved.
  • Page 9 Envase ......1 0514209 Cepillo de limpieza ....1 © 2001 Wagner Spray Tech. All rights reserved.
  • Page 10 GARANTíA LIMITADA POR UN AÑO - Manténgala archivada Este producto, fabricado por Wagner Spray Tech Corporation (Wagner), está garantizado contra defectos de materiales y de mano de obra por un año a partir de la fecha de compra, si se utiliza de acuerdo con las instrucciones y recomendaciones especificadas por Wagner. Esta garantía no cubre daños producidos por uso indebido, accidentes, negligencia del usuario o desgaste normal del producto.

Table of Contents