1. Manuals
  2. Brands
  3. Quality Craft Manuals
  4. Indoor Fireplace
  5. M450P-32ACH
  6. Instruction manual

Quality Craft M450P-32ACH Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
I N S T R U C T I O N M A N U A L
ATTENTION:
1. Find a location for the fireplace heater
that is protected from direct sunlight.
2. Do not plug the unit into the power outlet
before reading all instructions
ELECTRIC FIREPLACE HEATER
M450P-32ACH
(NDF-65NB-1)
.

Advertisement

Table of Contents
loading

Related Manuals for Quality Craft M450P-32ACH

Summary of Contents for Quality Craft M450P-32ACH

  • Page 1 ELECTRIC FIREPLACE HEATER I N S T R U C T I O N M A N U A L M450P-32ACH (NDF-65NB-1) ATTENTION: 1. Find a location for the fireplace heater that is protected from direct sunlight. 2. Do not plug the unit into the power outlet...

  • Page 2: Important Safety Instructions

    S A F E T Y I N S T R U C T I O N S IMPORTANT SAFETY INSTRUCTIONS WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAU- TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: IMPORTANT 1) Read all instructions before using this...
  • Page 3 S A F E T Y I N S T R U C T I O N S 8) Do not run cord under carpeting. Do not 16) Do not plug this product into a receptacle cover cord with throw rugs, runners, or controlled by a wall switch or dimmer.

  • Page 4: Parts List

    S A F E T Y I N S T R U C T I O N S W) KD screws A 15 AMP circuit is required to operate this X) Plastic connector heater. If the breaker trips when the heater Y) SELF REPAIR SET is used then you may need to move the Touch-up repair paint (bottle)
  • Page 5 A S S E M B LY I N S T R U C T I O N S Please DO NOT fully tighten the KD screws NOTE: If the KD SCREW(S) do not fit during until all panels are assembled. assembly, loosen the 2 screws to adjust the PLASTIC CONNECTOR until the PANELS/KD Step 1: Attach 2 CONNECTOR [S] to the FRONT...
  • Page 6 A S S E M B LY I N S T R U C T I O N S fig. E Step 6: Carefully place the INSERT into the fig. G unit opening. The front of INSERT should Step 8: Attach 3 MOUNTING CLIPS [U] onto be flush with the front of the mantel.
  • Page 7 A S S E M B LY I N S T R U C T I O N S 2. Position the back edge of the mantle close to the wall. 3. Attach the SAFETY CABLE to the mantle using the SCREW FOR MANTEL. See fig. J 4.

  • Page 8: Operation

    O P E R A T I O N DIMMER CONTROL KNOB: Turn the dimmer dial clockwise or counter clockwise to get the desired flame intensity. The dimmer switch can only be used when the ON/OFF switch is in the on position. NOTE: When the ON/OFF switch is turned off, all other heater functions will stop even ON/OFF: Press this button for main power...

  • Page 9: Replacing The Light Bulbs

    M A I N T E N A N C E RISK OF FIRE: REPAIR SET DO NOT EXCEED THE RECOMMENDED BULB WATTAGE. REPLACING THE LIGHT BULBS TOUCH-UP REPAIR PAINT Step 1: Remove 4 screws on the back of fireplace and remove the rear Paint directly on the mantel unit if cover of the unit.
  • Page 10 M A I N T E N A N C E OPTION 1: Use the spare KD NUTS, KD SCREWS and PLASTIC CONNECTOR 1. Place the PLASTIC CONNECTOR on the mantel unit and mark the drill-holes as Fig. D shown in Fig. B. 4.

  • Page 11: Warranty

    This warranty is void if in the opinion Fig. G Fig. H of Quality Craft the unit has been tampered with, altered, misused, damaged, abused 3. Attach the SMALL L-BRACKET and lock in or used with the wrong power source. Light place with SCREWS as shown in Fig.

Table of Contents