Quality Craft MM480PG-47CW Instruction Manual

Quality Craft MM480PG-47CW Instruction Manual

Electric fireplace heater

Advertisement

ELECTRIC FIREPLACE HEATER
MODEL: MM480PG-47CW (NDF-79NR)
IMPORTANT:
Please note when you open the carton carefully check the
unit and make sure there is no damage. If you have any
problems with assembling the unit, with how the various
functions work or with damage or missing parts please call
1-800-459-4409 (9:00am - 5:00pm EST) immediately for
service.
NOTE: DO NOT RETURN UNIT TO THE STORE BEFORE CALLING
THE TOLL FREE NUMBER . Do not dispose of your cartons until
you are completely satisfied with your new fireplace heater.
NOTE: Light bulbs may become loose during shipping. If the
flame effect is dim or does not work, please check that light
bulb or bulbs are finger tight in socket. See instructions for
replacing bulb or bulbs.
INSTRUCTION MANUAL
ATTENTION:
1. Find a location for the fireplace heater that is protected from
direct sunlight.
2. Do not plug the unit into the power outlet before reading all
instructions.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE.
IMPORTANT SAFETY
INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDING THE
FOLLOWING:
1) Read all instructions before using this electric fireplace heater.
2) This electric fireplace heater is hot when in use. To avoid
burns, do not let bare skin touch hot surfaces. The grill directly
in front of the heater outlet becomes hot during heater opera-
tion. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least 3 feet (0.9 m)
away from the front of the unit and keep them away from the
sides and rear.
3) Extreme caution is necessary when any heater is used by, or
near, children or individuals with disabilities and whenever the
fireplace is left operating
and unattended.
4) Always unplug fireplace when not in use.
5) Do not operate any electric fireplace with a damaged cord or
plug or after the heater malfunctions, has been dropped or
damaged in any manner.
6 Do not use outdoors.
7) This electric fireplace heater is not intended for use in
bathrooms, laundry areas and similar indoor locations. Never
locate heater where it may fall into a bathtub or other water
container.
8) Do not run cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Arrange cord away from
traffic area and where it will not be tripped over.
9) To disconnect fireplace, turn controls to off, then remove plug
from outlet.
10) Connect to properly grounded outlets only.
11) Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock or
fire, or damage the heater.
12) To prevent a possible fire, do not block air intakes or exhaust
in any manner. Do not use on soft surfaces, like a bed, where
openings may become blocked.
13) A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint, or flammable liquids are
used or stored.
14) Use this fireplace heater only as described in this manual. Any
other use not recommended by the manufacturer may cause
fire, electric shock, or injury to persons.
15) Avoid the use of an extension cord because the extension cord
may overheat and cause a risk of fire. However, if you have to
use an extension cord, the cord shall be No.14 AWG minimum
size and rated not less than 1875 watts.
16) Caution: Do not plug this product into a receptacle controlled
by a wall switch or dimmer.
17) When storing or transporting the unit and cord, keep in a dry
place, free from excessive vibration and store so as to avoid
damage.
CAUTION:
IF YOU USE THIS HEATER IN CONJUNCTION WITH A THERMAL
1

Advertisement

Table of Contents
loading

Summary of Contents for Quality Craft MM480PG-47CW

  • Page 1: Important Safety Instructions

    ELECTRIC FIREPLACE HEATER 2) This electric fireplace heater is hot when in use. To avoid MODEL: MM480PG-47CW (NDF-79NR) burns, do not let bare skin touch hot surfaces. The grill directly in front of the heater outlet becomes hot during heater opera- tion.
  • Page 2: Parts List

    CONTROL, A PROGRAM CONTROLLER, A TIMER OR ANY OTHER S) Mounting Screws ..............4 DEVICE THAT SWITCHES THE HEATER ON AUTOMATICALLY, U) Mounting Clips ..............2 REMEMBER TO OBSERVE ALL SAFETY WARNINGS AT ALL V) Mounting Bracket ..............2 TIMES. THE FIREPLACE HEATER HAS SAFETY OVERHEAT W)Medium KD Screws ..............4 PROTECTION.
  • Page 3 MANTEL ASSEMBLY: CAUTION: PLACE A PIECE OF CARDBOARD OR PROTECTIVE SHEET ON THE FLOOR IN ORDER TO AVOID SCRATCHING THE DECORATIVE SURFACE OF YOUR MANTEL DURING ASSEMBLY. DO NOT FULLY TIGHTEN THE KD SCREWS UNTIL ALL PANELS ARE ASSEMBLED. Fig. D Step 1: Attach all PLASTIC CONNECTORS (X) to the PANELS (C, E, F, G and H) as shown in Fig.
  • Page 4: Fireplace Insert Installation

    Step 4: Attach 2 MOUNTING CLIP (U) on the top of the INSERT. Attach 4 MOUNTING SCREWS (S) with the INSERT as shown in Fig. K and 2 MEDIUM KD SCREWS (W) and 2 Spacers (Q) with the MANTEL UNIT as shown in Fig. L. Fig.
  • Page 5: Operation

    O/I: Press this button for main power function. The unit will beep and the indicator light will be on. Pressing again will stop the main power function. Once the heater is switched off, the indicator light will flash and the unit will keep working with air flow for 5 more seconds.
  • Page 6: Remote Control Battery Replacement

    FLAME/LOG: Press this button once for flame effect. The unit will be beep and the indicator light will be ON. The bulbs for flame effect & log-set will be ON. To adjust the flame intensity, hold down the button - the flame optics will go higher or lower. Once you have found the desired setting, release the button.
  • Page 7 REPAIRS If any problems are found with the original parts during mantel assembly such as the panels cannot be installed with the plastic connector. Try to solve by one of these following methods: Fig. E Tools required: Electric drill, drill bits 3/4 inches (10 mm) or 1/16 inches (2 mm), pencil, hammer, Philips screwdriver, safety goggles and gloves (if necessary).
  • Page 8: Warranty

    The company’s sole obligation is to repair or replace the unit. This warranty is void if in the opinion of Quality Craft the unit has been tampered with, altered, misused, damaged, abused or used with the wrong power source. Light bulbs are not covered by this warranty.

Table of Contents