Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Quality Craft M707P-2628FCN
Summary of Contents for Quality Craft M707P-2628FCN
- Page 1 ELECTRIC FIREPLACE HEATER I N S T R U C T I O N M A N U A L M707P-2628FCN NDF-62N ATTENTION: 1. Find a location for the fireplace heater that is protected from direct sunlight. 2. Do not plug the unit into the power outlet before you...
-
Page 2: Important Safety Instructions
S A F E T Y I N S T R U C T I O N S IMPORTANT SAFETY INSTRUCTIONS WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAU- TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDI NG THE FOLLOWING: IMPORTANT Please note when you open the carton... - Page 3 S A F E T Y I N S T R U C T I O N S heater where it may fall into a bathtub or and cause a risk of fire. However, if you have other water container. to use an extension cord, the cord shall be No.14 AWG minimum size and rated not 8) Do not run cord under carpeting.
- Page 4 S A F E T Y I N S T R U C T I O N S at C is available for connecting three-blade grounding-type plugs to two-slot recep- tacles. The green grounding plug extend- ing from the adapter must be connected to a permanent ground such as a properly grounded outlet box.
-
Page 5: Parts List
A S S E M B LY I N S T R U C T I O N S PARTS LIST: Fireplace insert A) Top panel B) Base C) Front panel D) Left front panel E) Right front panel F) Left side panel G) Right side panel R) Medium KD screws S) Short KD screws... - Page 6 A S S E M B LY I N S T R U C T I O N S Please DO NOT fully tighten the KD screws side panel [G] to right front panel [E] with 2 until all panels are assembled. KD screws.
-
Page 7: Fireplace Insert Installation
A S S E M B LY I N S T R U C T I O N S WARNING: Make sure the fireplace insert controls are in the OFF position and the unit is NOT plugged in. Step 1: Carefully place the INSERT in the unit opening. -
Page 8: Control Panel
A S S E M B LY I N S T R U C T I O N S the risk of the fireplace being tipped over has been properly connected to a grounded accidentally. WARNING: This CABLE may electrical outlet, it is ready to operate. reduce possible risk of injury if the fireplace is improperly handled, but is not a substi- OPERATION BY THE... -
Page 9: Operation
O P E R A T I O N TEMPERATURE CONTROL: To adjust the Step 2: You will find 1 X 40W Type B-10 bulb temperature to your individual require- under log-set bed. ments, turn the temperature control dial to the right (clockwise) to increase the desired Step 3: Loosen and remove the burnt out temperature and to the left for lower tem-... - Page 10 M A I N T E N A N C E TOUCH UP REPAIR PAINT 1. Paint directly on the mantel unit if necessary. Fig. A. fig. B 2. Drill the holes with diameter 3/4 inches (10 mm) and depth 3/4 inches (10 mm) on the mantel.
- Page 11 R E P A I R S E T / C L E A N I N G fig. G fig. H Option 2: Use the SMALL L-BRACKETS and 3. Attach the SMALL L-BRACKET and lock SCREWS. in place with SCREWS as shown in Fig. H 1.
-
Page 12: Warranty
The company’s sole obliga- tion is to repair or replace the unit. This war- ranty is void if in the opinion of Quality Craft the unit has been tampered with, altered, misused, damaged, abused or used with the wrong power source.