Download Print this page

Quality Craft MM190P-2628FCN Instruction Manual

Electric fireplace heater

Advertisement

Quick Links

ELECTRIC FIREPLACE HEATER
MODEL: MM190P-2628FCN (NDF-62N)
IMPORTANT:
Please note when you open the carton carefully check the
unit and make sure there is no damage. If you have any
problems with assembling the unit, with how the various
functions work or with damage or missing parts please call
1-800-459-4409 (9:00am - 5:00pm EST) immediately for
service.
NOTE: DO NOT RETURN UNIT TO THE STORE BEFORE CALLING
THE TOLL FREE NUMBER . Do not dispose of your cartons until
you are completely satisfied with your new stove heater.
NOTE: Light bulbs may become loose during shipping. If the
flame effect is dim or does not work, please check that light
bulb or bulbs are finger tight in socket. See instructions for
replacing bulb or bulbs.
INSTRUCTION MANUAL
ATTENTION:
1. Find a location for the fireplace heater that is protected from
direct sunlight.
2. Do not plug the unit into the power outlet before reading all
instructions.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE.
IMPORTANT SAFETY
INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDING THE
FOLLOWING:
1) Read all instructions before using this electric fireplace heater.
2) This electric fireplace heater is hot when in use. To avoid
burns, do not let bare skin touch hot surfaces. The grill directly
in front of the heater outlet becomes hot during heater opera-
tion. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least 3 feet (0.9 m)
away from the front of the unit and keep them away from the
sides and rear.
3) Extreme caution is necessary when any heater is used by, or
near, children or individuals with disabilities and whenever the
fireplace is left operating and unattended.
4) Always unplug fireplace when not in use.
5) Do not operate any electric fireplace with a damaged cord or
plug or after the heater malfunctions, has been dropped or
damaged in any manner.
6) Do not use outdoors.
7) This electric fireplace heater is not intended for use in
bathrooms, laundry areas and similar indoor locations. Never
locate heater where it may fall into a bathtub or other water
container.
8) Do not run cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Arrange cord away from
traffic area and where it will not be tripped over.
9) To disconnect fireplace, turn controls to off, then remove plug
from outlet.
10) Connect to properly grounded outlets only.
11) Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock or
fire, or damage the heater.
12) To prevent a possible fire, do not block air intakes or exhaust
in any manner. Do not use on soft surfaces, like a bed, where
openings may become blocked.
13) A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint, or flammable liquids are
used or stored.
14) Use this fireplace heater only as described in this manual. Any
other use not recommended by the manufacturer may cause
fire, electric shock, or injury to persons.
15) Avoid the use of an extension cord because the extension cord
may overheat and cause a risk of fire. However, if you have to
use an extension cord, the cord shall be No.14 AWG minimum
size and rated not less than 1875 watts.
16) Caution: Do not plug this product into a receptacle controlled
by a wall switch or dimmer.
17) When storing or transporting the unit and cord, keep in a dry
place, free from excessive vibration and store so as to avoid
damage.
1

Advertisement

loading

Summary of Contents for Quality Craft MM190P-2628FCN

  • Page 1: Important Safety Instructions

    ELECTRIC FIREPLACE HEATER WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, MODEL: MM190P-2628FCN (NDF-62N) ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: 1) Read all instructions before using this electric fireplace heater.
  • Page 2: Parts List

    CAUTION: T) Medium KD screws ............2 IF YOU USE THIS HEATER IN CONJUNCTION WITH A THERMAL U) Short KD screws ............... 3 CONTROL, A PROGRAM CONTROLLER, A TIMER OR ANY OTHER V) Mounting brackets ............2 DEVICE THAT SWITCHES THE HEATER ON AUTOMATICALLY, W) KD screws ...............47 REMEMBER TO OBSERVE ALL SAFETY WARNINGS AT ALL TIMES.
  • Page 3 Step 2: Attach left front panel [D] to left side panel [F] with 3 KD screws. Attach right front panel [E] to right side panel [G] with 3 KD screws. See Fig. B. MANTEL ASSEMBLY: Fig. B CAUTION: PLACE A PIECE OF CARDBOARD OR PROTECTIVE SHEET ON THE FLOOR IN ORDER TO AVOID SCRATCHING THE DECORATIVE SURFACE OF YOUR MANTEL DURING ASSEMBLY.
  • Page 4: Fireplace Insert Installation

    Step 2: Attach the top of INSERT to the mantel with 3 short KD screws [U]. Attach 2 mounting brackets [V] at the bottom sides of INSERT with 2 Medium KD screws [T]. See Fig F. Fig. D Step 5: Attach top panel [A] to the unit as shown in Fig. E with 3 KD screws.
  • Page 5: Operation

    MAINTENANCE OPERATION MAINTENANCE WARNING: After reading complete instructions, confirm all controls on fireplace are in the OFF position. Plug the fireplace into a Disconnect power and unplug the power cord before attempting 15AMP/120Volt outlet. If the cord does not reach, you may use any maintenance or cleaning to reduce the risk of fire, electric an extension cord rated for a minimum of 1875 WATTS.
  • Page 6 REPAIR SET 2. Drill the holes with diameter 3/4 inches (10 mm) and depth 3/4 inches (10mm) on the mantel. Each Plastic Connector needs 3 holes. See Fig. C. TOUCH-UP REPAIR PAINT Paint directly on the mantel unit if necessary. Fig. A Fig.
  • Page 7: Warranty

    The company’s sole obligation is to repair or replace the unit. This warranty is void if in the opinion of Quality Craft the unit has been tampered with, altered, misused, damaged, abused or used with the wrong power source. Light bulbs and remote batteries are not covered by this warranty.