Quality Craft M850P-36ACN Instruction Manual
  1. Manuals
  2. Brands
  3. Quality Craft Manuals
  4. Indoor Fireplace
  5. M850P-36ACN
  6. Instruction manual

Quality Craft M850P-36ACN Instruction Manual

Electric fireplace heater
Hide thumbs
Table of Contents

Advertisement

Quick Links

ELECTRIC FIREPLACE HEATER
I N S T R U C T I O N M A N U A L
M850P-36ACN
NDF-65NB-1
ATTENTION:
1. Find a location for the fireplace heater that is protected
from direct sunlight.
2. Do not plug the unit into the power outlet before you
read all instructions.

Advertisement

Table of Contents
loading

Related Manuals for Quality Craft M850P-36ACN

Summary of Contents for Quality Craft M850P-36ACN

  • Page 1 ELECTRIC FIREPLACE HEATER I N S T R U C T I O N M A N U A L M850P-36ACN NDF-65NB-1 ATTENTION: 1. Find a location for the fireplace heater that is protected from direct sunlight. 2. Do not plug the unit into the power outlet before you...

  • Page 2: Important Safety Instructions

    S A F E T Y I N S T R U C T I O N S IMPORTANT SAFETY INSTRUCTIONS WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAU- TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: 1) Read all instructions before using this IMPORTANT...
  • Page 3 S A F E T Y I N S T R U C T I O N S 8) Do not run cord under carpeting. Do not 16) Do not plug this product into a receptacle cover cord with throw rugs, runners, or controlled by a wall switch or dimmer.
  • Page 4 S A F E T Y I N S T R U C T I O N S heater. If the breaker trips when the heater is used then you may need to move the heater to another location or unplug other appliances that are on the same circuit.

  • Page 5: Parts List

    A S S E M B LY I N S T R U C T I O N S PARTS LIST: A) Top panel B) Base panel C) Side panel D) Left front panel E) Upper front panel 1 F) Lower front panel 1 G) Right front panel S) Connector T) Short KD screws...
  • Page 6 A S S E M B LY I N S T R U C T I O N S Step 5: Place the LOWER FRONT PANEL [F] in between the lower section of 2 FRONT PANELS [D and G] and attach with 2 KD SCREWS (1 screw each side).
  • Page 7 A S S E M B LY I N S T R U C T I O N S Step 10: Tighten all KD SCREWS. Step 11: Carefully move the assembled unit to the desired location. The Fireplace Mantel should not be positioned in an area exposed to direct sunlight.

  • Page 8: Operation

    O P E R A T I O N fig. J After reading complete instructions, confirm all controls on fireplace are in the OFF posi- tion. Plug the fireplace into a 15AMP/120Volt O/I: Press this button for main power and outlet.

  • Page 9: Replacing The Light Bulbs

    M A I N T E N A N C E RISK OF FIRE: DIMMER CONTROL KNOB: Turn the dimmer DO NOT EXCEED THE dial clockwise or counter clockwise to get RECOMMENDED BULB the desired flame intensity. The dimmer WATTAGE. switch can only be used when the O/I switch is in the ON position.
  • Page 10 C L E A N I N G / W A R R A N T Y REPAIR SET OPTION 1: Use the spare KD NUTS, KD SCREWS and PLASTIC CONNECTOR 1. Place the PLASTIC CONNECTOR on the mantel unit and mark the drill-holes as shown in Fig.
  • Page 11 C L E A N I N G / W A R R A N T Y 4. Attach the PLASTIC CONNECTOR and lock in place with KD SCREWS as shown in Fig. E. fig. G fig. H 3. Attach the SMALL L-BRACKET and lock in place with SCREWS as shown in Fig.

  • Page 12: Warranty

    The company’s sole obligation is to repair or replace the unit. This warranty is void if in the opinion of Quality Craft the unit has been tampered with, altered, misused, damaged, abused or used with the wrong power source. Light bulbs are not covered by this warranty.

Table of Contents