Mitsubishi PLA-A12BA Technical Data Book page 17

PKA-A24KA PKA-A24KAL
PKA-A36KA PKA-A36KAL
Left side
Knockout hole
for left piping
2-29/32(74)
A
1-3/16(30)
1-3/8(35)
2-19/32(66)
Sleeve
(purchased locally)
[2-15/16
([75)
Required space(Indoor unit)
Min.8-21/32(220)
Min.2-27/32(72.4)
1-31/32(50)
2-15/16(75)
3-15/16(100)
4-19/32(117)
4-29/32(125)
5-19/32(142)
7-9/16(192)
9-17/32(242)
11-1/2(292)
PKA-A30KA
16-11/16(423.7)
33-21/32(855)
Front side(Grille open)
Filter hook
Vane(auto)
B
Through hole
[2-15/16~[3-5/32
([75~[80)
Air inlet
Air outlet
Min.2(50.5)
[ [
4- 11/32( 9) Bolt hole
[ [
75- 3/16( 5.1)
Tapping
screw hole
5/8(15.5)
0
31/32(25)
11(279.5)
Knockout hole for
rear piping
Wall hole for
2-15/16×18-29/32(75×480)
left rear piping
PKA-A30KAL
Top side
17(431.7)
Front side
9-1/2(241)
46-1/16(1170)
2
17-15/32(444)Gas pipe
1
18-31/32(482)Liquid pipe
3
23-1/32(585)Drain hose
Under side
Louver(manual)
Knock out hole
for lower piping
C
2-9/16(65)
Center measurement hole
[3/32([2.5)
Mount board
Wall hole for
right rear piping
Right side
3/16(5)
11-5/8(295)
Operation lamp
Knock out hole
for right piping
DEFROST/STAND BY lamp
Receiver
Terminal block for Outdoor unit
Terminal block for power supply (option)
Terminal block for
MA-remote controller (only PKA-A·KA models)
Emergency operation switch
(cooling/heating)
4-27/32(123)
6-1/16(154)
5-9/32(134)
Piping connection department
Refrigerant pipe: 3/8 O.D([9.52)
1 Liquid pipe
B
Flared connection: 3/8F
Refrigerant pipe: 5/8 O.D([15.88)
2 Gas pipe
Flared connection: 5/8F
3 Drain hose
5/8([16) O.D
Knockout hole for piping
B
3-1/32(77)
3-7/16(87)
13/32(10.7)
Indoor unit outline
2-1/8(54)
1-1/4(32)
31/32(25)
1/2(12.5)
0
1/2(12.5)
1-15/32(37.5)
2-15/32(62.5)
3-7/16(87.5)
4-1/8(104.5)
5-3/32(129.5)
6-9/16(167)
8-17/32(217)
9-1/32(229.5)
10-13/32(264)
11-1/2(292)
12-5/32(308.5)
12-1/4(311)
Unit: inch (mm)
Mount board
C
A
2-9/16(65)
17