Technical Data; Safety Rules - Hilti TE 2 Operating Instructions Manual

Technical data

Rated power
Rated voltage
Rated current input
en
Mains frequency
Weight of tool without side handle
Dimensions (l×h×w)
Minimum distance between wall and hole drilled
No load speed
Hammering speed:
Precision hammering action
Full hammering action
Single impact energy Nm (J):
Precision hammering action
Full hammering action
Typical drilling performance in medium-hard B35
concrete
Right of technical changes reserved

Safety rules

1. General safety rules
-WARNING- Read all instructions! Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury. The term "power tool" in all of
the warnings listed below refers to your mains operat-
ed (corded) power tool or battery operated (cordless)
power tool.
SAVE THESE INSTRUCTIONS
1.1 Work area safety
a) Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable liq-
uids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
1.2 Electrical safety
a) Power tool plugs must match the outlet. Never mod-
ify the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of elec-
tric shock.
2
Printed: 07.07.2013 | Doc-Nr: PUB / 5070802 / 000 / 00
700 W
120 V
6.5 A
50–60 Hz
2.4 kg / 5.3 lbs (TE2 / TE2-S)
2.7 kg / 6.0 lbs (TE2-M)
352×203×89 mm / 14.3×8×3.5 in (TE2 / TE2-S)
360×203×89 mm / 14.2×8×3.5 in (TE2-M)
34 mm (1.3 in)
0– 930 r.p.m. (hammer drilling)
0–1200 r.p.m. (in 1st gear TE2 / TE2-S / TE2-M)
0–2500 r.p.m. (in 2nd gear TE 2-M)
0–2600 blows/min. (TE 2-S)
0–4600 blows/min (TE 2 / TE 2-S / TE 2-M)
0.6 Nm / 0.4 ft lbs (TE 2-S)
1.8 Nm / 1.3 ft lbs (TE 2 / TE 2-S / TE 2-M)
8 mm dia.: 550 mm/min (
10 mm dia.: 500 mm/min (
12 mm dia.: 400 mm/min (
b) Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrig-
erators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
1.3 Personal safety
a) Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use
a power tool while you are tired or under the influ-
ence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b) Use safety equipment. Always wear eye protec-
tion. Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal
injuries.
" dia.: 21.7 in/min)
5 /
16
" dia.: 19.7 in/min)
3 /
8
" dia.: 15.7 in/min)
1 /
2