Hilti TE2 Operating Instructions Manual
Hide thumbs
Also See for TE2:
- User manual ,
- Operating instructions manual (190 pages) ,
- Manual (172 pages)
Table of Contents
Advertisement
Quick Links
02_BA_TE2_S_M_P1_en.qxd
TE 2/TE 2-E/TE 2-S/TE 2-M Rotary Hammer
It is essential that the operating
instructions are read before the
tool is operated for the first time.
Always keep these operating
instructions together with the tool.
Ensure that the operating
instructions are with the tool when
it is given to other persons.
Operating controls
Chuck release ring (TE 2-M)
Function selector switch
Control switch
Forwards / reverse switch (TE 2 / TE 2-S / TE 2-M)
Lockbutton
Component parts
Dust shield
Chuck
Side handle
Type plate
Contents
General information
31.08.2007
10:39 Uhr
General information
cates points of particular importance to safety. The
instructions at these points must always be observed
in order to avoid the risk of serious injury.
instructions
before use.
tions can be found on the fold-out cover pages. Keep
these pages open while you read the operating instruc-
tions.
In these operating instructions, the power tool to which
these operating instructions apply is referred to as "the
tool".
Description
The TE 2 / TE 2-E / TE 2-S / TE 2-M is an electrically pow-
ered rotary hammer with pneumatic hammering mech-
anism designed for professional use.
The following items are supplied: power tool, (quick-
release chuck TE 2-M), operating instructions, grease
(except TE 2-E), toolbox.
Page
11
- The tool must be connected to an alternating current
11
13
- The tool is for hand-held use only.
14
- The tool must not be used in places where the sur-
15
16
- Changes or modifications to the tool are not per-
16
17
- To avoid the risk of injury, use only the genuine Hilti
17
17
- Observe the information printed in the operating
18
18
19
19
Seite 11
In these operating instructions, this symbol indi-
Caution: high voltage
Read the
Return waste
operating
material for
recycling
The numbers refer to the illustrations. The illustra-
The following conditions must always be observed
when the tool is in use:
electric supply in compliance with the information
given on the type plate.
rounding conditions may present a risk of explosion.
missible.
accessories and additional equipment specified for
use with this tool.
instructions concerning operation, care and main-
tenance. The tool and its ancillary equipment may
present hazards when used incorrectly by untrained
personnel or when used not as directed.
en
11
Advertisement
Table of Contents
Related Manuals for Hilti TE2
Summary of Contents for Hilti TE2
-
Page 1: Table Of Contents
– Changes or modifications to the tool are not per- Drilling missible. Forwards/reverse rotation – To avoid the risk of injury, use only the genuine Hilti accessories and additional equipment specified for Insert tools and accessories use with this tool. - Page 2 02_BA_TE2_S_M_P1_en.qxd 31.08.2007 10:39 Uhr Seite 12 – The tool is intended for professional use.The tool Variable speed switch may be operated, serviced and repaired only by Rotary-only drilling mode authorized, trained personnel. This personnel must Gearing and hammering mechanism with permanent be informed of any special hazards that may be grease lubrication encountered.
-
Page 3: Technical Data
Minimum distance between wall and hole drilled 34 mm Speed 0– 930 r.p.m. (hammer drilling) 0–1200 r.p.m. (in 1st gear TE2 / TE2-E / TE2-S / TE2-M) 0–2500 r.p.m. (in 2nd gear TE 2-M) Hammering speed: Precision hammering action 0–2600 blows/min. (TE 2-S) Full hammering action 0–4600 blows/min. -
Page 4: Safety Rules
02_BA_TE2_S_M_P1_en.qxd 31.08.2007 10:39 Uhr Seite 14 Safety rules tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turn- 1. General safety rules ing the power tool on. -
Page 5: Before Use
Seite 15 2. Additional safety rules c) Dirty or dusty electric tools should thus be checked at a Hilti service center at regular intervals, espe- 2.1 Personal safety cially if used frequently for working on conductive a) Wear ear protectors. Exposure to noise can cause materials. -
Page 6: Operation
02_BA_TE2_S_M_P1_en.qxd 31.08.2007 10:39 Uhr Seite 16 At low temperatures: The tool requires to reach a mini- 2. Turn the function selection switch to the hammer mum operating temperature before the hammering mech- drilling position ( ) until the gearing is engaged anism begins to operate. -
Page 7: Forwards/Reverse Rotation
Carefully wipe the sealing lip Accordingly, highest performance and longest life and grease it with a little Hilti grease. It is essential that expectancy can be achieved when you use this pow- the dust shield is replaced when the sealing lip is dam- er tool with Hilti insert tools. -
Page 8: Disposal
Return waste material for recycling Most of the materials from which Hilti power tools are manufactured can be recycled. The materials must be cor- rectly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old electric tools for recycling. -
Page 9: Troubleshooting
EC declaration of conformity Hilti Corporation Description: Rotary Hammer Designation: TE2 / TE 2-E / TE2-S / TE2-M Year of design: 2005 Peter Cavada Matthias Gillner We declare, under our sole responsibility, that this product Head of BU... - Page 10 02_BA_TE2_S_M_P1_en.qxd 31.08.2007 10:39 Uhr Seite 20...
Need help?
Do you have a question about the TE2 and is the answer not in the manual?
Questions and answers