Page 1
Ver. 1 SERVICE MANUAL MODEL E2A E1C E1K EUT DN-HS5500 DIRECT DRIVE TURNTABLE MEDIA PLAYER & CONTROLLER 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に もとづき、所定の許可を得て製造されております。 従ってサービスをおこなう際は、これらの安全性が維 持されるよう、このサービスマニュアルに記載されて いる注意事項を必ずお守りください。 For purposes of improvement, specifications and ● 本機の仕様は性能改良のため、予告なく変更すること ● design are subject to change without notice.
Front Panel. (2) HDD tray lid のねじ 2 本をはずし、HDD tray lid を抜 (2) Remove 2 screws on the HDD tray lid and pull out the き取る。 HDD tray lid. 2 screws HDD tray lid 4 screws Front Panel DN-HS5500...
3. Top shield 3. Top shield (1) Reverse the Top case unit. (1) Top case unit を裏返す。 (2) Remove the 5 screws on the Top shield showed in the (2) 下図で示した Top shield のねじ 5 本をはずす。 below drawing. 5 screws DN-HS5500...
押しながら、電源を ON にします。 「DENON power. Keep pressing the PARAMETERS DJ」が表示されるまで PARAMETERS ノブと knob and B ( ) button until "DENON DJ" ) ボタンを押し続けます。 サービスモー is displayed. When the service mode is set, ドになると、サービスモードの TOP 画面が表 the service mode's top menu appears.
Page 8
し、PARAMETERS ノブを押して確定します。 ・The contents of the preset memory are set to ・ プリセットメモリの内容を工場出荷状態にし the factory defaults. For details on the preset ます。 プリセットメモリの詳細は、 DN-HS5500 memory, see the DN-HS5500's Instruction の取り扱い説明書を参照して下さい。 Manual. HS5500_Init ・ "Complete!!" is displayed when initialization is ・ 初期化が終了すると、"Complete!!" を表示し...
Page 10
状態とチェック結果 チェック状態と結果が表示されます。 displayed here. DRIVE_Check DRIVE_Check received is checked. が表示されます。 mode モード The checking status and results are displayed. チェックを行います。 When the process has completed 正常終了時 normally When the process 異常終了時 has completed abnormally DN-HS5500...
Page 11
・ Deck1 または Deck2 の PARAMETERS ノブを回 わして、FUNCTION チェックモード画面から Audio_OSC を選択し、PARAMETERS ノブを押 して確定します。 LINE OUT1/2 端子にテスト信号を出力します。 RAM の固定アドレスのリード / ライト Audio_OSC Audio_OSC mode チェックを行います。 モード Not yet used. Nothing happens when this is 未対応です。選択しても何も実行しません。 selected. TOUCH_Init TOUCH_Init mode モード DN-HS5500...
Page 12
File Name を確定します。 to set "File Name" A rti s t A rti s t Album Album Ti tl e Ti tl e Genre Genre Sel ect Pa ra m.〉〉 Sel ect Pa ra m.〉〉 Sel ect Pa ra m.〉〉 Sel ect Pa ra m.〉〉 DN-HS5500...
Page 13
-10% or less: D-SYNC LED, MIDL LED, DEVICE LED ・ヒートランモードを終了するときは、Deck1 及び Deck2 の CUE ( ) ボタンを押して再 ・To end the heat run mode, press the CUE 生を停止させてから、電源を OFF にします。 ) buttons on Decks 1 and 2 to stop playback, then turn the power off. DN-HS5500...
Page 14
HS5500 SW CHK mode モード ・全ボタンのチェックが終了すると、チェック ・Once all the buttons have been checked, the 結果を表示します。 results of checking are displayed. ・PARAMETERS ノブを押すと、サービス画面の ・Press the PARAMETERS knob to return to the TOP 画面に戻ります。 top screen in the service mode. SW CHK OK! SW CHK OK! DN-HS5500...
Page 15
0 to 1022. ・フェーダー値 ・Fader value : 最大 1018 以上 1018 or more クリック点 センタータップ値± 25 Click point Central tap value ± 25 最小 3 以下 3 or less ・センタータップ値 435 ∼ 589 ・Center Tap value 435~589 DN-HS5500...
Page 16
PLATTER ADJ mode for the 実行し上記範囲内となることを確認します。 second time, after that execute PLATTER ・ PLAYLIST を押すとサービスモードの TOP 画面 CHK mode and verify that it is within the に戻ります。 range. ・ Press the PLAYLIST button to return to the top screen in the service mode. DN-HS5500...
・バージョンアップ開始を指定します。 Press the PLAY/PAUSE ( ) button. PLAY/PAUSE( ) ボタンを押します。 To cancel, turn the power off. キャンセルするときは、電源を OFF します。 ・Be careful that the power does not get ・バージョンアップ中は、電源が OFF にならな turned off while the firmware is being いよう注意してください。 updated. DN-HS5500...
Is the voltage of 20V or more supplied to the D904, C941 component, and replace it if defective. EMITTERpin of TR905? いいえ TR905のEMITTER pinに20V以上の電圧が D904、C941部品がリーク、ショート又は開放して 供給されているか? いないかチェックし、不良部品を交換。 Check TR905 and the periphery circuit, はい and replace it if defective. TR905と周辺部品をチェックし、不良部品を交換。 DN-HS5500...
Page 20
Check TR803 and the periphery circuit, and service it if (MUTEドライブ信号)がL(-9V)になっているか? been the TR803 collector (MUTE drive signal) L(-9V)? defective. はい IC804、IC805の7pin、1pinから、JK801までの周辺 Check periphery circuit from 7pin and 1pin to 回路を確認し、不良部品を交換。 JK801 of IC804 and IC805, and replace it if defective. DN-HS5500...
/ KEY Buff (Option) SPDIF 24bit EXT HDD MP3 DEC SPUIF OUT CPU Buff OUT Buff [dBFs] [dBV] <Analog MAX 12.5dBV> Analog OUT 6.5dBV [dBFs] +2.78dBV GAIN = 2.78dBV SPDIF OUT -6.0dBV <-95dBV> -100 -100 -110 -110 -120 -120 DN-HS5500...
Page 23
6 Serializers 256K Bytes Program Fetch Program/Data McASP2 ROM Page3 2 Serializers 256K Bytes + DIT Program SPI1 Cache 32K Bytes SPI0 I2C0 High-Performance Crossbar Switch I2C1 Interrupts MAX0 CONTROL MAX1 Events UHPI EMIF dMAX Peripheral Interrupt and DMA Events DN-HS5500...
Page 25
Control input select access mode (0) AMUTE2 DSP interrupt ACLKX2 McASP2 transmit bit clock DVDH I/O supply (+3.3V) DVDH I/O supply (+3.3V) EM_WAIT Not used (Asynchronous wait input) AFMOE Not used (External memory out put enable) /SPI0_/ENA Not used ADBCK DN-HS5500...
Page 26
D_GND D_GND D_GND D_GND D_GND CVDL Core supply (+1.2V) SHDB14 CPU bus data 14 SHDB13 CPU bus data 13 AEMA10 External memory bus address 10 AEMB1 External memory bank address 1 D_GND D_GND Not used CVDL Core supply (+1.2V) DN-HS5500...
Page 27
External memory bus address 6 AEMA5 External memory bus address 5 /EMU1 Emulation pin 1 Not used Not used AEMD22 External memory bus data 22 DVDH I/O supply (+3.3V) AEMD18 External memory bus data 18 AEMD16 External memory bus data 16 DN-HS5500...
Page 28
External memory bus data 0 AEMD14 External memory bus data 14 D_GND AEMD11 External memory bus data 11 AEMD9 External memory bus data 9 ASDQM1 External memory byte enable signal ASDCKE External memory clock enable signal DVDH I/O supply (+3.3V) D_GND DN-HS5500...
Page 29
Send LCD reading start trigger to CPU (CPU:IRQ0) SH_RDY Wait (CPU:-WAIT) IIC clock line L SH_BS (CPU:-BS) SH_DRQ DMA transfer request (CPU:DRQ0) SH_IRQc Interrupt request 3 (PS/2 to CPU:PINT3) SH_CS7 LCD, IDE, PANEL, PS/2, FPGA 32 bits bus width (CPU) SH_DAK DMA transfer accept (CPU:DACK0) DN-HS5500...
Page 30
3-8 ENC signal (PANEL 1, 2 is common) VCCIO4 VCCIO4 PNL_KEYSC1 3-8 ENC signal (PANEL 1, 2 is common) PNL_KEYSC2 3-8 ENC signal (PANEL 1, 2 is common) PNL_BLNK Blank signal (PANEL 1, 2 is common), (LED _ON/OFF) P_KEY_DDAT_2 DN-HS5500...
Page 31
14 bits address 1 (CPU) SH_AD3 14 bits address 1 (CPU) SH_AD2 14 bits address 1 (CPU) VCCIO2 VCCIO2 SH_AD1 14 bits address 1 (CPU) SH_RW Data R/W (CPU:RD/-WR) SH_DB12 32 bits data bus (CPU) SH_DB13 32 bits data bus (CPU) VCCIO2 VCCIO2 DN-HS5500...
Page 32
32 bits data bus (CPU) SH_DB09 32 bits data bus (CPU) VCCIO2 VCCIO2 SH_DB10 32 bits data bus (CPU) SH_DB11 32 bits data bus (CPU) SH_DB24 32 bits data bus (CPU) SH_DB25 32 bits data bus (CPU) SH_DB26 32 bits data bus (CPU) DN-HS5500...
Page 34
A/D converter user debugging interface 3 interface mode timer (DAC) (ADC) interface with FIFO (IIC3) control (WDT) (SCIF) (H-UDI) Port Port Port Port Port Port WDTOVF output JTAG input/output Analog output Analog input, C bus Serial input/output ADTRG input input/output DN-HS5500...
Page 36
Data bus 29 ..SHDB28 Data bus 28 PVcc V3SH I/O supply (+3.3V) PVss D_GND ..SHDB27 Data bus 27 ..SHDB26 Data bus 26 ..SHDB25 Data bus 25 ..SHDB24 Data bus 24 PVcc V3SH I/O supply (+3.3V) ..SHDB23 Data bus 23 DN-HS5500...
Page 37
LCD, 32 bits bus width -CASL SHCAS CAS output Clock enable -CS2 External chip select 2 -CS3 Not used DQMUU DQMUU D31~D24 DQMUL DQMUL D23~D16 DQMLU DQMLU D15~D8 DQMLL DQMLL D7~D0 -RASL SHRAS RAS output -CS4 Not used PVcc V3SH I/O supply (+3.3V) DN-HS5500...
Separated power from Vcc, used for output buffers to 3, 9, 43, 49 VccQ for I/O Buffer improve noise. Ground for I/O Separated power from Vss, used for output buffers to 6, 12, 46, 52 VssQ Buffer improve noise. 36, 40 No Connection No Connection DN-HS5500...
Page 40
Pin No. Symbol Function Start-up signal Display data signal (Latch clock) Display data signal (Shift clock) VLED Power supply for LED Backlight DISP Display control signal (ON "H", OFF "L") Display data Power supply for logic Ground Voltage for control LCD DN-HS5500...
Indicates number of zeros after effective number. 2-digit effective number. Units: pF. 220pF (0 or 1) Indicates number of zeros after effective number. 2-digit effective number. Units: pF. When the dielectric strength is indicated in AC, "AC" is included after the dieelectric strength value. DN-HS5500...
EXPLODED VIEW WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。 DN-HS5500...
2X4 CBTS-(P)-B VINYL BAG 00D2032442003 2P PIN CORD 00D5114752003 INST. MAMUAL 00D5114754001 INST.MANUAL(CD-ROM) 00MZD01800130 USB(A)-USB(B) CABLE S.S.LIST COM.(EX) SERVICE STATION LIST WARRANTY(COM.1Y.) WARRANTY SUB ASSY 00D5012388003 CARTON CASE E3,E2 00D5012389002 CARTON CASE (J) CONT.CARD(L)SUB ASSY BAR CODE LABEL ASSY DN-HS5500...
NOTICE: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. DN-HS5500...