No
Mode
Operation and Function
・Turn the PARAMETERS knob to select
"FUNCTION CHK" from the service mode's
top menu, then press the PARAMETERS knob
to set the function check mode.
q ---Top menu---
The top of the menu for the function check
mode appears.
w HS5500_Init
The contents of the preset memory are set
to the factory defaults.
e *RAM_Check
Not yet used.
r *CPU-DSP_Check
Not yet used.
t HDD_Format(Option)
When the hard disk of the option is added,
the hard disk is formatted in FAT32.
y DRIVE_Check
D-SYNC. terminal transmission/reception is
FUNCTION check
2
checked.
mode
u *Audio_OSC
Not yet used.
i TOUCH_Init
Not yet used.
o Heat_Run
The specified track is played repeatedly.
Q0 ---end menu---
The end of the FUNCTION check mode's
menu is displayed.
・When the BACK (
) button is pressed
while the FUNCTION check mode is being
executed or after the FUNCTION check mode
has been executed, the FUNCTION check
mode's top menu reappears.
・ When the BACK (
) button is pressed
before the FUNCTION check mode has been
executed, the service mode's top menu reap-
pears.
・Turn the PARAMETERS knob to select
"HS5500_Init" from the FUNCTION check
mode's top menu, then press the PARAME-
TERS knob to set "HS5500_Init" mode.
・The contents of the preset memory are set to
the factory defaults. For details on the preset
memory, see the DN-HS5500's Instruction
Manual.
HS5500_Init
・ "Complete!!" is displayed when initialization is
2.1
completed.
mode
Display
When the PARAMETERS
knob is turned, items 0 to 9
are displayed, three items
at a time.
0 ---top menu---
1 HD2500_Init
2 *RAM_Check
When the PARAMETERS
3 *CPU-DSP_Check
knob is pressed to set the
4 HDD_Format
selected item, the item is
5 Drive_CHK
highlighted.
6 *Audio_OSC
7 TOUCH_Init
8 Heat_Run
9 ---end menu---
The checked contents and
results are displayed.
When the process
has completed
normally
When the process
has completed
abnormally
DN-HS5500
No
モード
操 作 と 機 能
・PARAMETERS ノブを回して、サービスモード
の TOP 画面から FUNCTION CHK を選択し、
PARAMETERS ノブを押して確定します。
q ---Top menu---
FUNCTION チェックモードのメニューの先
頭を示します。
w HS5500_Init
プリセットメモリの内容を工場出荷状態に
設定します。
e *RAM_Check
未対応。
RAM の固定アドレスのリード / ライト
チェックを行います。
r *CPU-DSP_Check
未対応。
CPU-DSP 間の通信チェックを行います。
t HDD_Format ( オプション )
オプションで HDD を追加した時、HDD を
FAT32 でフォーマットします。
FUNCTION チェッ
y DRIVE_Check
2
クモード
D-SYNC. 端子の送受信チェックをおこない
ます。
u *Audio_OSC
未対応。
LINE OUT1/2 端子にテスト信号を出力しま
す。
i TOUCH_Init
未対応。
o Heat_Run
指定された曲をリピート再生します。
Q0 ---end menu---
FUNCTION チェックモードのメニューの最
後を示します。
・FUNCTION チェックモード実行中または実行
後に BACK(
) ボタンを押すと、 FUNCTION
チェックモードの TOP 画面に戻ります。
・F U N C T I O N
チ ェッ クモ ード 実 行前 に
BACK(
) ボタンを押すと、サービスモー
ドの TOP 画面に戻ります。
・ PARAMETERS ノブ を回 し て、FUNCTION
チェックモード画面から HS5500_Init を選択
し、PARAMETERS ノブを押して確定します。
・ プリセットメモリの内容を工場出荷状態にし
ます。 プリセットメモリの詳細は、 DN-HS5500
の取り扱い説明書を参照して下さい。
・ 初期化が終了すると、"Complete!!" を表示し
HS5500_Init
ます。
2.1
モード
8
表 示
PARAMETERSノブを回す
と、0∼9の項目が3つ
ずつ表示されます。
0 ---top menu---
1 HD2500_Init
2 *RAM_Check
PARAMETERSノブを押し
3 *CPU-DSP_Check
確定すると、反転表示
4 HDD_Format
されます。
5 Drive_CHK
6 *Audio_OSC
7 TOUCH_Init
8 Heat_Run
9 ---end menu---
チェック内容と結果が表示
。
されます
正常終了時
異常終了時