Sinclair SYMPHONY MS-H09AISW PT Service Manual page 13

(1) Under Sleep 3 mode, press "Turbo" button for a long time, remote control enters into user individuation sleep setting status, at this
time, the time of remote control will display "1hour ",the setting temperature "88" will display the corresponding temperature of last
setting sleep curve and blink (The first entering will display according to the initial curve setting value of original factory);
(2) Adjust "+" and "-" button, could change the corresponding setting temperature, after adjusted, press "Trubo "button for confirmation;
(3) At this time, 1hour will be automatically increased at the timer postion on the remote control, (that are "2hours " or "3hours " or
ON/OFF button
1
"8hours "), the place of setting temperature "88" will display the corresponding temperature of last setting sleep curve and blink;
+/- button
2
(4) Repeat the above step (2) ～ (3) operation, until 8hours temperature setting finished,sleep,curve setting finished, at this time, the
MODE button
3
remote control will resume the original timer display;temperature display will resume to original setting temperature.
FAN button
Sleep3- the sleep curve setting under Sleep mode by DIY could be inquired:
4
The user could accord to sleep curve setting method to inquire the presetting sleep curve,enter into user individuation sleep setting
SWING button
5
status, but do not change the temperature, press "Turbo" button directly for confirmation.Note: In the above presetting or enquiry
I FEEL button
6
procedure,if continuously within10s, there is no button pressed, the sleep curve setting within 10s, there is no button pressed, the sleep
/ button
7
curve setting status will be automatically quit and resume to display the original displaying. In the presetting or enquiry procedure, press
"ON/OFF" button, "Mode" button, "Timer"button or "Sleep" button, the sleep curve setting or enquiry status will quit similarly.
SLEEP button
8
TEMP button
9
Press this button, you can see indoor set temperature, indoor ambient temperature on indoor unit's display. The setting on remote
QUIET button
10
controller is selected circularly as below:
ClOCK button
11
ON/OFF button
1
T-ON T-OFF button /
12
+/- button
2
TURBO button
13
MODE button
3
When selecting " " with remote controller or no display, temperature indicator on indoor unit displays set temperature; When
X-FAN button
14
ON/OFF button
1
FAN button
selecting " " with remote controller, temperature indicator on indoor unit displays indoor ambie nt temperature; 3s later or within 3s
4
LIGHT button
15
it receives other remote control signal that will return to display the setting temperature. +/- button
SWING button
2
5
Caution:
MODE button
I FEEL button
3
6
This model hasn't outdoor ambient temperature display function. While remote controller
ON/OFF button
FAN button
1
4
button
/
7
can operate " " and indoor unit displays set temperature.
SWING button
+/- button
5
2
It's defaulted to display set temperature when turning on the unit.
SLEEP button
8
MODE button I FEEL button
Only for the models with temperature indicator on indoor unit.
6
3
TEMP button
9
FAN button
/ button
4
7
QUIET button
10
SWING button
5
SLEEP button
8
ClOCK button
Press this button, the Quiet status is under the Auto Quiet mode (display "
11
I FEEL button
ON/OFF button
6
TEMP button
1
9
OFF (there is no signal of "
/
T-ON T-OFF button
12
button
/
Fan and Dry mode;Under the Quiet mode (Display" +/- button
7
QUIET button
2
10
TURBO button
13
MODE button
SLEEP button
8
3
ClOCK button
11
X-FAN button
14
FAN button
TEMP button
4
9
T-ON T-OFF button /
Press CLOCK button,blinking.
12 LIGHT button
15
SWING button
5 QUIET button
2 seconds increases or decreases the time by 1 minute every 0.5 second and then by 10 minutes every 0.5 second. During blinking
10
TURBO button
13
I FEEL button
after setting, press CLOCK button again to confirm the setting, and
6
ClOCK button
11 X-FAN button
14
/ button
7
LIGHT button
T-ON T-OFF button /
15
12
SLEEP button
8
TURBO button
13 Press T-ON button to initiate the auto-ON timer. To cancel the auto-timer program, simply press this button again.
TEMP button
After press of this button,
9 X-FAN button
14
to adjust the time value. Every press of either button changes the time setting by 1 minute. Holding down either button rapidly changes
QUIET button
LIGHT button
10
15
the time setting by 1 minute and then 10 minutes. Within 5 Seconds after setting, press TIMER ON button to confirm.
ClOCK button
11
Press T-OFF button to initiate the auto-off timer. To cancel the auto-timer program, simply press the button again.TIMER OFF setting is
T-ON T-OFF button /
the same as TIMER ON.
12
TURBO button
13
X-FAN button
14
Press this button to activate / deactivate the Turbo function which enables the unit to reach the preset temperature in the shortest time.
LIGHT button
In COOL mode, the unit will blow strong cooling air at super high fan speed. In HEAT mode, the unit will blow strong heating air at super
15
high fan speed.
no display
"displayed),after powered on, the Quiet OFF is defaulted. Note: the Quiet function cannot be set up in
" Under the Quiet mode) the fan speed is not available.
Within 5 seconds, pressing + or - button adjusts the present time. Holding down either button above
disappears and "ON "blink s . 00:00 is displayed for ON time setting. Within 5 seconds, press + or - button
Auto
Auto
"signal )and Quiet mode (display "
Auto
then will be constantly displayed.
" singal) and Quiet
13