Advertisement
5.0 Operating Guide
5.1 Understanding the DS7443, DS7445, and DS7447 Keypads
• The DS7443 is a 6 zone LED keypad; its LEDs represent the zones of the system.
• The DS7445 is an 8 zone LED keypad; its LEDs represent the zones of the system (LEDs for zones 7 and 8 are not used).
• The DS7447 is an alpha-numeric LCD keypad.
All three keypads display information on various control panel functions. A built-in sounder is used to annunciate keystroke
entries and as an interior warning device.
Volume Control (DS7445 and DS7447 only): The keypad sounder volume can be adjusted using the [1] and [4] keys along
with the [*] key. Hold the [*] key while pressing the [1] key to increase the volume or the [4] key to decrease the volume. The
volume adjustment does not affect the volume during an alarm.
Backlight Control (DS7447 only): The display backlight intensity can be adjusted using the [3] and [6] keys along with the
[*] key. Hold the [*] while pressing the [3] key to increase brightness or the [6] key to decrease brightness.
NOTE: After the backlight and volume are adjusted, you must arm then disarm the system once to store this information in
the control panel. If power is disconnected before the panel is armed, the backlight and volume levels return to the
default settings.
Armed
Status
Power
Fire
1
4
7
*
DS7447 KEYPAD
This chart will help you understand what each Light/LED represents.
LIGHT
Armed
The control panel is disarmed.
(red)
Status
One or more zones are not ready
(green)
to arm.
Power
The control panel has lost power.
(green)
No AC for battery.
Fire
There are no fire alarms.
(red)
Perimeter*
The perimeter is not armed.
(yellow)
Supervisory*
This light will not be sued by the
(yellow)
DS7060.
Bell Silenced*
The bells do not need to be or have
(yellow)
not been silenced.
Trouble*
There are no trouble conditions.
(yellow)
Zone LEDs**
There are no zone alarms.
(red)
* = This light is present on the DS7445 only.
DS7060-AUS Reference Guide
On
Off
2
3
5
6
Perimeter
Only
No
8
9
Entry
#
0
Bypass
System
Reset
DS7443 KEYPAD
OFF
An exit delay is in progress or an
alarm has occurred.
One or more zones are bypassed.
Control panel problems. Refer to
Error displays.
A fire zone is in alarm.
This light will not flash.
Not used.
This light will not flash.
This light will not flash.
A zone (1-6) is in alarm.
Copyright © 2001 Detection Systems, Inc.
Armed
1
4
Status
2
5
Power
3
6
Fire
On
Off
1
2
3
Perimeter
4
5
6
Only
No
7
8
9
Entry
*
0
#
Bypass
System
Reset
FLASHING
** = This light is present on the DS7443 and DS7445.
Armed
Perimeter
Status
Supervisory
1 2 3 4 5 6 7 8
Power
Bell Silenced
Fire
Trouble
1
2
3
4
5
6
7
8
9
0
*
#
DS7445 KEYPAD
ON
The control panel is armed and no
alarms have occurred.
All zones are ready to arm.
Normal operation.
A fire trouble condition exists.
The perimeter is armed.
Not used.
The bells have been silenced. To clear,
enter the Fire Reset command.
A trouble condition exists.
A zone (1-6) is not ready to arm or if a
fire zone, a trouble condition exists.
On
Off
Perimeter
Only
No
Entry
Bypass
System
Reset
Page 5
Advertisement
