Color Reproduction Adjustment; Color Reproduction Adjustment (Without Nd Filter); Color Reproduction Adjustment (With Nd Filter) - Sony DSC-F505 Service Manual

13. Color Reproduction Adjustment

Adjust the color Separation matrix coefficient so that proper color
reproduction is produced.

13-1. Color Reproduction Adjustment (Without ND Filter)

Mode STILL
Subject Color bar chart
(Color bar standard picture frame)
Adjustment Page F
Adjustment Address 41 to 48, 5C to 5F
Note 1: This adjustment should be carried out upon completion of "Auto
White Balance Standard Data Input" and "Auto White Balance
Adjustment".
Note 2: Check that the data of page: 6, address: 02 is "00". If not, turn the
power of the unit OFF/ON.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 5, address: F1, and set data: FF.
3) Check that the picture frame is set to the specified position.
(Refer to "5. Picture Frame Setting".)
4) Select page: B, address: 41, set data: 30, and press the PAUSE
button.
5) Select page: F, address: 37, and set data: 9B.
6) Select page: 6, address: 01, set data: AB, and press the PAUSE
button.
7) Select page: 6, address: 01, set data: A9, and press the PAUSE
button.
(The color reproduction adjustment (without ND filter) is
performed and the adjustment data is stored in page: F, address:
41 to 48 and 5C to 5F.)
8) Select page: 6, address: 02, and check that the data is "01".
9) Perform "Color Reproduction Check" and "Processing after
Completing Adjustments".
Processing after Completing Adjustments:
1) Select page: B, address: 41, set data: 00, and press the PAUSE
button.
2) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: F, address: 37, set data: 93, and press the PAUSE
button.
4) Select page: 5, address: F1, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.

13-2. Color Reproduction Adjustment (With ND Filter)

Mode
Subject
Adjustment Page
Adjustment Address
Note 1: This adjustment should be carried out upon completion of "Auto
White Balance Standard Data Input" and "Auto White Balance
ND Filter Compensation Adjustment".
Note 2: Check that the data of page: 6, address: 02 is "00". If not, turn the
power of the unit OFF/ON.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 5, address: F1, and set data: FF.
3) Check that the picture frame is set to the specified position.
(Refer to "5. Picture Frame Setting".)
4) Select page: B, address: 41, set data: 30, and press the PAUSE
button.
5) Select page: F, address: 37, set data: 9B, and press the PAUSE
button.
6) Select page: 6, address: 1C, set data: 03, press PAUSE button,
and wait for one second.
7) Select page: 6, address: 12, set data: 80, press PAUSE button,
and wait for two seconds.
8) Select page: 6, address: 12, set data: 00, press PAUSE button,
and wait for two seconds.
9) Select page: 6, address: 01, set data: C3, and press the PAUSE
button.
10) Select page: 6, address: 01, set data: C1, and press the PAUSE
button.
(The color reproduction adjustment (with ND filter) is
performed and the adjustment data is stored in page: F, address:
51 to 58 and 60 to 63.)
11) Select page: 6, address: 02, and check that the data is "01".
12) Perform "Color Reproduction Check" and "Processing after
Completing Adjustments".
Processing after Completing Adjustments:
1) Select page: B, address: 41, set data: 00, and press the PAUSE
button.
2) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 6, address: 1C, set data: 00, and press the PAUSE
button of the adjustment remote commander.
4) Select page: F, address: 37, set data: 93, and press the PAUSE
button.
5) Select page: 5, address: F1, and set data: 00.
6) Select page: 0, address: 01, and set data: 00.
5-29
STILL
Color bar chart
(Color bar standard picture frame)
F
51 to 58, 60 to 63