Horizontal Left With Left Vent - Rheem *96V series Installation Instructions Manual

HORIZONTAL LEFT / LEFT VENT HORIZONTAL LEFT / LEFT VENT HORIZONTAL LEFT / LEFT VENT
AIRFL OW
PARTS NEEDED: PARTS NEEDED: PARTS NEEDED: PARTS NEEDED:
FROM PARTS BAG(PROVIDED WITH UNIT) FROM PARTS BAG(PROVIDED WITH UNIT)
INTAKE COUPLING
FROM CONVERSION KIT RXGY-CK FROM CONVERSION KIT RXGY-CK
1/2" VINYL
.559" CONDENSATE
CAP (YELLOW)
TRAP DRAIN PLUG
TOOLS/MATERIALS NEEDED: TOOLS/MATERIALS NEEDED: TOOLS/MATERIALS NEEDED:
PLIERS PLIERS
DRILL
1/4" HEX HEAD DRIVER 1/4" HEX HEAD DRIVER
1/8" DRILL BIT
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE
NOTE: STEPS 1- 4 SHOWN WITH FURNACE IN "AS SHIPPED CONDITION" NOTE: STEPS 1- 4 SHOWN WITH FURNACE IN "AS SHIPPED CONDITION" NOTE: STEPS 1- 4 SHOWN WITH FURNACE IN "AS SHIPPED CONDITION"
1
1
HOSE "D"
(RETAIN)
VENT HOSE
(DISCARD)
1 - REMOVE CONDENSATE TRAP AND HOSES. 1 - REMOVE CONDENSATE TRAP AND HOSES.
(RETAIN HOSE D FOR LATER USE.) (RETAIN HOSE D FOR LATER USE.)
(NOTE: TO REMOVE TRAP, REMOVE (2) SCREWS AND (NOTE: TO REMOVE TRAP, REMOVE (2) SCREWS AND
PULL STRAIGHT OUT). PULL STRAIGHT OUT).
W/NUT
1/4" BLACK
VENT TUBING VENT TUBING
TUBING CUTTER TUBING CUTTER
2
2a - REMOVE .403" DRAIN PLUG FROM FLUE ELBOW - DISCARD. 2a - REMOVE .403" DRAIN PLUG FROM FLUE ELBOW - DISCARD.
2b - INSTALL INTAKE COUPLING IN TOP PLATE. 2b - INSTALL INTAKE COUPLING IN TOP PLATE.
2c - INSTALL 1/2" VINYL CAP (YELLOW) IN INDUCER COUPLING AS SHOWN. 2c - INSTALL 1/2" VINYL CAP (YELLOW) IN INDUCER COUPLING AS SHOWN. 2c - INSTALL 1/2" VINYL CAP (YELLOW) IN INDUCER COUPLING AS SHOWN.
2d - REMOVE RECTANGLE FLUSH MOUNT PLUG FROM JACKET SIDE-DISCARD. 2d - REMOVE RECTANGLE FLUSH MOUNT PLUG FROM JACKET SIDE-DISCARD. 2d - REMOVE RECTANGLE FLUSH MOUNT PLUG FROM JACKET SIDE-DISCARD.
PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS
!
FROM THE FROM THE PARTS BAG AND CONVERSION KIT
YOU MUST HAVE THE PARTS OUTLINED BELOW BEFORE YOU MUST HAVE THE PARTS OUTLINED BELOW BEFORE YOU MUST HAVE THE PARTS OUTLINED BELOW BEFORE
PROCEEDING. PROCEEDING.
CONDENSATE CONDENSATE
TRAP GASKET TRAP GASKET
INTAKE
COUPLING
2d
2a
AND CONVERSION KIT RXGY-CK.
(X3)
#8 X 1/2"
1/2" DRAIN
SCREW
HOSE E
INSTALL
2b
2c
1/2" VINYL 1/2" VINYL
CAP CAP
(INSTALL) (INSTALL)
ST-A1194-35-01
39