Downflow With Right Vent (Non Zero Clearance) - Rheem *96V series Installation Instructions Manual

DOWNFLOW W/ RIGHT VENT (NON-ZERO CLEARANCE) DOWNFLOW W/ RIGHT VENT (NON-ZERO CLEARANCE) DOWNFLOW W/ RIGHT VENT (NON-ZERO CLEARANCE) DOWNFLOW W/ RIGHT VENT (NON-ZERO CLEARANCE) DOWNFLOW W/ RIGHT VENT (NON-ZERO CLEARANCE)
PARTS NEEDED: PARTS NEEDED:
FROM PARTS BAG (PROVIDED WITH UNIT) FROM PARTS BAG (PROVIDED WITH UNIT)
(X3)
(X2)
HOSE
#8 X 1/2"
CLAMP
SCREW
FROM CONVERSION KIT RXGY-CK FROM CONVERSION KIT RXGY-CK
2" PIPE GROMMET
2-5/8" FLUSH 2-5/8" FLUSH 2-5/8" FLUSH 2-5/8" FLUSH
( 3.375)
MOUNT PLUG MOUNT PLUG
TOOLS/MATERIALS NEEDED: TOOLS/MATERIALS NEEDED: TOOLS/MATERIALS NEEDED:
DRILL
(1) 1/8" DRILL BIT
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE
NOTE: STEPS 1- 5 SHOWN WITH FURNACE IN "AS SHIPPED CONDITION" NOTE: STEPS 1- 5 SHOWN WITH FURNACE IN "AS SHIPPED CONDITION" NOTE: STEPS 1- 5 SHOWN WITH FURNACE IN "AS SHIPPED CONDITION"
1
1a
1b
1a - REMOVE FLUE TRANSITION, TRANSITION COUPLING, AND ELBOW. 1a - REMOVE FLUE TRANSITION, TRANSITION COUPLING, AND ELBOW. 1a - REMOVE FLUE TRANSITION, TRANSITION COUPLING, AND ELBOW.
(NOTE: REMOVE COUPLING ON INDUCER WITH ELBOW FOR EASIER REMOVAL). (NOTE: REMOVE COUPLING ON INDUCER WITH ELBOW FOR EASIER REMOVAL) (NOTE: REMOVE COUPLING ON INDUCER WITH ELBOW FOR EASIER REMOVAL)
1b - REMOVE TRAP AND HOSES. RETAIN HOSE D FOR LATER USE. 1b - REMOVE TRAP AND HOSES. RETAIN HOSE D FOR LATER USE. 1b - REMOVE TRAP AND HOSES. RETAIN HOSE D FOR LATER USE.
(NOTE:TO REMOVE TRAP REMOVE (2) SCREWS AND PULL STRAIGHT OUT). (NOTE:TO REMOVE TRAP REMOVE (2) SCREWS AND PULL STRAIGHT OUT). (NOTE:TO REMOVE TRAP REMOVE (2) SCREWS AND PULL STRAIGHT OUT).
PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS
FROM THE FROM THE PARTS BAG AND CONVERSION KIT
!
YOU MUST HAVE THE PARTS OUTLINED BELOW BEFORE YOU MUST HAVE THE PARTS OUTLINED BELOW BEFORE YOU MUST HAVE THE PARTS OUTLINED BELOW BEFORE
PROCEEDING. PROCEEDING.
HOSE -
DOUBLE
ELBOW
TUBE C
(X4)
CONDENSATE
#8 X 1/2"
TRAP DRAIN
SCREW
PLUG .559"
(1) 3/16" DRILL BIT
PLIERS
FLUE TRANSITION (DISCARD) FLUE TRANSITION (DISCARD)
TRANSITION TRANSITION
COUPLING COUPLING
(DISCARD) (DISCARD)
ELBOW (DISCARD) ELBOW (DISCARD)
IDB COUPLING IDB COUPLING
(RETAIN) (RETAIN)
VENT HOSE VENT HOSE
(DISCARD) (DISCARD)
HOSE "D" HOSE "D"
(RETAIN) (RETAIN)
AND CONVERSION KIT RXGY-CK.
INTAKE AIR
INTAKE
COUPLING COUPLING
DIFFUSER
W/ NUT
1/2" DRAIN
5/8" DRAIN
HOSE E
HOSE B
(1) 1/4" HEX HEAD DRIVER
(1) 5/16 HEX HEAD DRIVER
2
2-5/8" 2-5/8"
2d
DISCARD
2a
NOTE:
IF THE IDB COUPLING IS IF THE IDB COUPLING IS
REMOVED, IT MUST BE REMOVED, IT MUST BE
REPLACED IN THE PROPER REPLACED IN THE PROPER
ORIENTATION. AN ARROW IS ORIENTATION. AN ARROW IS
PRESENT ON THE COUPLING PRESENT ON THE COUPLING
TO INDICATE THE DIREC- TO INDICATE THE DIREC-
TION OF EXHAUST FLOW. TION OF EXHAUST FLOW.
MAKE SURE THE ARROW MAKE SURE THE ARROW
POINTS IN THE CORRECT POINTS IN THE CORRECT
DIRECTION.
2a-REMOVE 3-3/8" FLUSH MOUNT PLUG FROM JACKET - DISCARD. 2a-REMOVE 3-3/8" FLUSH MOUNT PLUG FROM JACKET - DISCARD. 2a-REMOVE 3-3/8" FLUSH MOUNT PLUG FROM JACKET - DISCARD.
2b-RELOCATE 2-3/8" FLUSH MOUNT PLUG FROM JACKET TO TOP PLATE. 2b-RELOCATE 2-3/8" FLUSH MOUNT PLUG FROM JACKET TO TOP PLATE. 2b-RELOCATE 2-3/8" FLUSH MOUNT PLUG FROM JACKET TO TOP PLATE.
2c-RELOCATE 1/2" VINYL CAP (YELLOW) IN INDUCER COUPLING. 2c-RELOCATE 1/2" VINYL CAP (YELLOW) IN INDUCER COUPLING. 2c-RELOCATE 1/2" VINYL CAP (YELLOW) IN INDUCER COUPLING.
2d-INSTALL 2-5/8" FLUSH PLUG IN TOP PLATE. 2d-INSTALL 2-5/8" FLUSH PLUG IN TOP PLATE.
BULKHEAD
COUPLING
CONDENSATE CONDENSATE
1/4" BLACK 1/4" BLACK
TRAP BRACKET TRAP BRACKET TRAP BRACKET TRAP BRACKET
VENT TUBE
(DOWN FLOW) (DOWN FLOW)
FLAT HEAD SCREWDRIVER FLAT HEAD SCREWDRIVER
TUBING CUTTER
INSTALL
2c
ST-A1194-30-02
2b
19