Cimbali M32 Bistro dt1 Owner's Manual page 32

English
Machines connected to the main water supply
" Before using the machine make sure that:
the main electricity supply ON/OFF switch is ON;
the main water supply tap is open. "
Switch on the mains switch (4). Led "machine on" (18) will light up.
If the water level in the tank is below the minimum level, the "tank
level" indicator light (11) lights up, the tank is automatically topped up
to the optimal level, and the indicator light (11) switches off.
At the end of this operation, the water level in the boiler is checked.
If the level is below the minimum, the "boiler level" indicator light (12)
lights up, and the boiler is filled up to the optimal level (indicator light 12
off).
"Heating" now begins.
At the end of the working day, switch off the mains switch (4).
" Before using the machine make sure that:
the main electricity supply ON/OFF switch is ON;
the main water supply tap is open. "
At the end of the day, turn the machine OFF by turning the main ON/OFF switch (4) to position 0.
Gas lighting (2 dispenser unit + GAS machines only)
" Don't light the gas when the boiler is at working
pressure. "
Before using the machine check that:
- the main electricity supply ON/OFF switch is ON;
- the main water supply tap is open;
- the gas supply tap is open.
Turn the main ON/OFF switch (4) to position 1.
The operations described under " Daily Switch-On " are completed.
Press and turn the gas lighter knob (27) to position "B", and keep it
pressed for about 30 seconds.
Check through the observation window (28) that the burner is lit, and
then release knob (27).
"Heating" now begins.
During heating, if one of the coffee dispensing push buttons (13, 14,
15, 16 or 21) is pressed, the machine dispenses a coffee at the tem-
perature reached at the time.
The same applies when the milk (9), cappuccino (10) and steam (20)
dispensing push buttons are pressed.
The hot water dispensing push button (19) is deactivated until the working
pressure is reached.
Heating is completed when the "machine at working temperature" indi-
Setting at work - 1 dispenser unit machines
Setting at work - 2 dispenser unit machines
Heating phase
Machines not connected to the main water supply
" Before using the machine make sure that:
the main electricity supply ON/OFF switch is ON;
the water in the tank is at the maximum level. "
Switch on the mains switch (4). Led "machine on" (18) will light up.
If the water level in the tank is below the minimum level, the "tank
level" indicator light (11) lights up, and the tank should be filled up to
the optimal level using a jug. On completion, the indicator light (11)
switches off.
At the end of this operation, the level of the water in the boiler is checked.
If the level is below the minimum, the "boiler level" indicator light (12)
lights up, and the boiler is filled up to the optimal level (indicator light 12
off).
"Heating" now begins.
Turn the main ON/OFF switch (4) to position 1. The "machine ON"
indicator light (18) lights up.
If the water level in the boiler is below the minimum level, the "boiler
level" indicator light (12) lights up, and the boiler is filled up to the
optimal level (indicator light 12 off).
Turn the main ON/OFF switch (4) to position 2.
"Heating" now begins.
27
cator light (17) lights up (for machines with 1 dispenser unit only)
and the boiler gauge indicator (3) remains stable in the green area.
The machine is now ready to dispense coffee, milk, cappuccino, steam
and hot water.
To make sure the dispenser unit and the filter holder (7) are at similar
temperatures, turn press the START-STOP push button (21) and let
the machine dispense for a few seconds. Then press the push button
(21) again.
English
B