Table of Contents
Advertisement
Important Safety Information
• Check hoses and parts for signs of damage, a leak can inject
material into the skin. Inspect hose before each use. Replace
any damaged hoses or parts.
• This system is capable of producing 3300 PSI / 22.8 MPa. Only
use replacement parts or accessories that are specified by the
manufacturer and that are rated a minimum of 3300 PSI. This
includes spray tips, nozzle guards, guns, extensions, fittings,
and hose.
• Always engage the trigger lock when not spraying. Verify the
trigger lock is functioning properly.
• Verify that all connections are secure before operating the unit.
• Know how to stop the unit and bleed pressure quickly. Be
thoroughly familiar with the controls. Pressure will not be
released by turning off the motor. The PRIME/SPRAY valve
or pressure bleed valve must be turned to their appropriate
positions to relieve system pressure. Refer to PRESSURE
RELIEF PROCEDURE described in the pump manual.
• Always remove the spray tip before flushing or cleaning the
system.
NOTE TO PHySIcIAN:
Injection into the skin is a traumatic injury which can lead
to possible amputation. It is important to treat the injury as
soon as possible. DO NOT delay treatment to research toxicity.
Toxicity is a concern with some coatings injected directly
into the blood stream. consultation with a plastic surgeon or
reconstructive hand surgeon may be advisable.
WARNING: GENERAL
Can cause severe injury or property damage.
PREvENTION:
• Always wear appropriate gloves, eye protection, clothing
and a respirator or mask when painting. Hazardous vapors
- Paints, solvents, insecticides, and other materials can be
harmful if inhaled or come in contact with body. Vapors can
cause severe nausea, fainting or poisoning.
• Do not operate or spray near children. Keep children away
from equipment at all times.
• Do not overreach or stand on an unstable support. Keep
effective footing and balance at all times.
• Stay alert and watch what you are doing.
• Do not operate the unit when fatigued or under the influence
of drugs or alcohol.
• Do not kink or over-bend the hose. Airless hose can develop
leaks from wear, kinking and abuse. A leak can inject material
into the skin.
• Do not expose the hose to temperatures or pressures in excess
of those specified by manufacturer.
• Do not use the hose as a strength member to pull or lift the
equipment.
• Use lowest possible pressure to flush equipment.
• Follow all appropriate local, state and national codes
governing ventilation, fire prevention and operation.
• The United States Government Safety Standards have been
adopted under the Occupational Safety and Health Act
(OSHA). These standards, particularly part 1910 of the General
Standards and part 1926 of the Construction Standards should
be consulted.
• Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover. Check for damage or movement
of couplings. Immediately replace hose if any of those
conditions exist. Never repair a paint hose. Replace with a
conductive high-pressure hose.
• Do not spray outdoors on windy days.
© Titan Tool Inc. All rights reserved.
• Always unplug cord from outlet before working on equipment
(electric models only).
ImPORTANT: Do not lift cart handle when loading or unloading.
Specifications
Gallons per minute (GPM) ........................ 1.2 (4.5 LPM)
Maximum tip sizes ...................................... 0.034
Maximum pressure ..................................... 3300 PSI (22.8 MPa)
Voltage ............................................................ 100~120V AC, 50/60 Hz
Power ............................................................... .2.4 HP Infinity Plus Brushless®
Maximum current consumption ............ 15 A
Weight ............................................................. 95 lbs. (43.1 kg)
Maximum hose length .............................. 300' (91.4 m)
NOTE: maximum hose length may vary depending on the
hose diameter and the viscosity of the material
being sprayed.
Table of contents
Safety Precautions ........................................................................... 2
Français ..........................................................................................................16
Español ...........................................................................................................18
General Description ........................................................................ 4
Operation ......................................................................................... 4
Setup ................................................................................................ 4
Preparing to Spray........................................................................................5
Spraying ...........................................................................................................5
Control Panel Indicators .............................................................................6
Pressure Relief Procedure ..........................................................................6
Xact Digital Control System Operation (if equipped) ......................6
Spraying Technique ........................................................................ 8
Practice .............................................................................................................8
cleanup ............................................................................................ 9
Cleaning the Inlet Screen ...........................................................................9
maintenance .................................................................................... 9
General Repair and Service Notes ..........................................................9
Replacing the Motor Assembly .............................................................10
Replacing the Gears ...................................................................................10
Replacing the Transducer ........................................................................11
Replacing the PRIME/SPRAY Valve .......................................................11
Servicing the Fluid Section ......................................................................12
Replacing the Filters ..................................................................................13
Troubleshooting ............................................................................ 14
Xact Digital Control System Error Messages .....................................15
Parts Listings .................................................................................. 20
Main Assembly ............................................................................................20
Drive Assembly ............................................................................................21
Fluid Section Assembly ............................................................................22
High Rider Cart ............................................................................................23
Filter Plug Assembly ..................................................................................23
PRIME/SPRAY Valve Assembly ...............................................................23
Filter Parts ......................................................................................................24
Labels ..............................................................................................................24
Accessories ....................................................................................................26
Warranty ........................................................................................ 28
3
DC Motor
Advertisement
Table of Contents
