Download
Share
Print this page
EarthWay FLEX-SELECT F80 Series Assembly And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. EarthWay Manuals
  4. Spreader
  5. FLEX-SELECT F80 Series
  6. Assembly and operating instructions manual

EarthWay FLEX-SELECT F80 Series Assembly And Operating Instructions Manual

Adaptable broadcast spreader
Hide thumbs Also See for FLEX-SELECT F80 Series:

Advertisement

Quick Links

Download this manual
F80 & F130 FLEX-SELECT
Adaptable Broadcast Spreader
Assembly and Operating Instructions
PLEASE CONTACT US: IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY
QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME
TECHNICAL SUPPORT. SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: techsupport@earthway.com
HELPFUL HINTS:
; If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The
impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller
after each use as some fertilizer may become stuck on the impeller blades and will cause uneven spreading.
; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds
will change the spread patterns. Wet fertilizer will also change the spread pattern and flow rate.
; Clean and dry your spreader thoroughly after each use, wash between the shut-off plate and bottom of the hopper
regularly. To prevent rust, coat all metal parts (inside and out) including the frame tubes with a light oil, silicon spray, or
Fluid Film
.
®
; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
; When using Rock Salt to prevent damage to the gearbox remove salt from the hopper daily. Rock Salt will reconstitute
back into a solid block if left in the hopper overnight and will damage your gearbox if pushed with the salt in place.
©2014 Earthway Products, Inc. All rights reserved. EarthWay ® EV-N-SPRED ® , FLEX-SELECT ® , and SPRAY-PRO ® are registered trademarks of Earthway Products, Inc.
Use of trademarks or images are prohibited unless approved by Earthway Products, Inc. 1009 Maple Street Bristol, Indiana 46507
Series
®
WARNING
Do not use air tools to assemble.
To prevent seizing coat all bolts
with a wax or grease prior to
Remove all parts, hardware, and assemblies from carton
and lay them out on the floor to help in assembly.
Below are tools needed for assembly - 7/16"
wrench, ratchet and 7/16" socket, and pliers.
The following photos are for assembly
purposes, and please follow them from left to
right, top to bottom.
installation.
Download a color version of this
manual online at www.earthway.com
or Scan this QR Code.
9-2014 Pt# F52157
PAGE 1

Advertisement

loading

Related Manuals for EarthWay FLEX-SELECT F80 Series

Summary of Contents for EarthWay FLEX-SELECT F80 Series

  • Page 1 PAGE 1 ©2014 Earthway Products, Inc. All rights reserved. EarthWay ® EV-N-SPRED ® , FLEX-SELECT ® , and SPRAY-PRO ® are registered trademarks of Earthway Products, Inc. Use of trademarks or images are prohibited unless approved by Earthway Products, Inc. 1009 Maple Street Bristol, Indiana 46507...
  • Page 2 ASSEMBLY PAGE 2...
  • Page 3 ASSEMBLY - continued PAGE 3...
  • Page 4 ASSEMBLY - continued PAGE 4...

  • Page 5: Complete Assembly

    ASSEMBLY - continued CONFIRM THE CALIBRATION: Lever at #30 and the drop holes fully open COMPLETE ASSEMBLY: Install agitator, bend the agitator up slightly to prevent contact with the standard output tray, and install debris screen (press over 1/4 turn fasteners to secure) PAGE 5...

  • Page 6: Tray Installation

    TRAY INSTALLATION HIGH-OUTPUT AND LOW-OUTPUT: require the use of the Part #F12117 HIGH-OUTPUT AND LOW-OUTPUT: require the use of the Part #F12117 PAGE 6...

  • Page 7: Year Limited Warranty

    Products, Inc. To seek remedy under this warranty, contact Earthway Products, Inc. at 574-848-7491, techsupport@earthway. com or write to Earthway Products, Inc. P.O. Box 547 Bristol, Indiana 46507 and describe the nature of the manufacturing defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s) or product; any labor charges associated with repair or replacement of non-conformances are specifically excluded.
  • Page 8 50’ measuring tape, a small scale to weigh the material, bucket or container to hold the material for re-weighing, chalk or a line marking device, and (7) low baking tins. Using the EarthWay ® Bag Calibrator #77016 can greatly reduce the time needed for Gauge &...

  • Page 9: Coverage Area

    You may need to repeat this process to acquire the exact rate. The EV-N-SPRED Dual Port PRO Adjustable Shut-Off System ensures that EarthWay Professional spreaders ® ®...
  • Page 10 SIDE DEFLECTOR 33108 3/16" X 1" COTTER PIN ZINC Optional HEAVY DUTY RAIN COVER (F77080 for F80 / F77130 FOR F130) 33109 3/16" X 2" COTTER PIN ZINC Optional 12195 GAUGE OVERLAY- LESCO SETTINGS 33117 AGITATOR Standard 12196 GAUGE OVERLAY- EARTHWAY...
  • Page 11 SIDE DEFLECTOR 36103 3/16 X 2" COTTER PIN S.S. Optional HEAVY DUTY RAIN COVER (F77080 for F80 / F77130 FOR F130) 36104 3/16 X 1" COTTER PIN S.S. Optional 12195 GAUGE OVERLAY- LESCO SETTINGS 33117 AGITATOR Standard 12196 GAUGE OVERLAY- EARTHWAY...
  • Page 13 8.5m 7.9m ©2014 Earthway Products, Inc. All rights reserved. EarthWay® EV-N-SPRED®, Flex-Select®, and SPRAY-PRO® are registered trademarks of Earthway Products, Inc. Use of trademarks or images are prohibited unless approved by Earthway Products, Inc. 1009 Maple Street Bristol, Indiana 46507...
  • Page 14 ©2014 Earthway Products, Inc. All rights reserved. EarthWay® EV-N-SPRED®, Flex-Select®, and SPRAY-PRO® are registered trademarks of Earthway Products, Inc. Use of trademarks or images are prohibited unless approved by Earthway Products, Inc. 1009 Maple Street Bristol, Indiana 46507...

This manual is also suitable for:

Flex-select f130 seriesFlex-select seriesFlex-select f80Flex-select f130