ADJ INNO POCKET Z4 User Instructions page 9

Inno Pocket Z4
Channel Value
13
90 - 93
94 - 97
98 - 101
102 - 104
105 - 108
109 - 112
113 - 115
116 - 119
120 - 123
124 - 127
128 - 191
192 - 255
14
0 - 255
15 0 - 255
16
0 - 7
8 - 15
16 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
17 0 - 255
18
0 - 69
70 - 79 BLACKOUT W/ PAN/TILT MOVEMENT
80 - 89 DISABLE BLACKOUT WITH PAN/TILT
90 - 199
200 - 209
210 - 255
ADJ Products, LLC - www.adj.com - Inno Pocket Z4 Instruction Manual Page 23
19 Channel Mode
Function
COLOR MACROS
COLOR MACRO 23
COLOR MACRO 24
COLOR MACRO 25
COLOR MACRO 26
COLOR MACRO 27
COLOR MACRO 28
COLOR MACRO 29
COLOR MACRO 30
COLOR MACRO 31
COLOR MACRO 32
COLOR CHANGING
COLOR FADING
COLOR CHANGE/FADE SPEED
SLOW - FAST
ZOOM 10°- 60°
SHUTTER/STROBE
REMOTE
INPUT OUTPUT
SOUND CLOSED CONTROL
INPUT
OPEN
STROBING SLOW - FAST
OPEN
FAST CLOSE - SLOW OPEN
OPEN
SLOW CLOSE - FAST OPEN
OPEN
DMX512
RANDOM STROBING
DMX+,DMX-,COMMON
OPEN
MASTER DIMMER 0% - 100%
SPECIAL FUNCTIONS
NO FUNCTION
1
DMX512 OUT
3-PIN XLR
MOVEMENT
2
NO FUNCTION
RESET ALL
NO FUNCTION
SOUND
Inno Pocket Z4
lighting stores). Your cables should be made with a male and female
XLR connector on either end of the cable. Also remember that DMX
cable must be daisy chained and cannot be split.
Notice:
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable's shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR's outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
1 Ground
REMOTE
SOUND CONTROL
INPUT
Figure 3
Special Note: Line Termination.
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
COMMON
DMX +
1
DMX512 IN
3 3
3-PIN XLR
DMX -
2
ADJ Products, LLC - www.adj.com - Inno Pocket Z4 Instruction Manual Page 8
REMOTE
INPUT OUTPUT
CONTROL SOUND
INPUT
POWER
Be sure to follow figures two and three when making your own
DMX512
DMX+,DMX-,COMMON
COMMON
DMX +
1
DMX512 OUT
3
3-PIN XLR
DMX -
2
XLR Male Socket XLR Female Socket
2 Cold
2 Cold
INPUT OUTPUT
SOUND
3 Hot
3 Hot
POWER
Termination reduces signal errors and
avoids signal transmission problems
1
and interference. It is always advisable
3
to connect a DMX terminal, (Resistance
2
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
REMOTE
INPUT OUTPUT
CONTROL
INPUT
DMX Set Up
POWER
1 1
DMX512 IN
3 3
3-PIN XLR
2 2
Figure 2
XLR Pin Configuration
1 Ground
Pin 1 = Ground
REMOTE
INPUT OUTPUT
CONTROL
Pin 2 = Data Compliment (negative)
INPUT
Pin 3 = Data True (positive)
When longer runs of cable are
POWER
Figure 4
SOUN
Termination
avoids sign
and interfere
to connect a
120 Ohm 1/4
and PIN 3 (