How To Operate Your Friedrich Room Air Conditioner; To Set Mode Of Operation; To Adjust Temperature; To Adjust Fan Speed - Friedrich WallMaster WS08 Installation And Operation Manual

H o w o t o e p a r
Inspect product prior to installation.
If your air conditioner is installed and plugged into a proper
receptacle, it is ready to go. The first time the unit is started,
the compressor will delay for three minutes. See Automatic
Component Protection on the following page (See Figures 1
& 2, page 5.
1 Touch the Power button once. The unit will automatically be in
Cooling and
MoneySaver
set at 75 ° F (24°C) and the fan speed at F1, the sleep setting.
2
MoneySaver® is a feature that cycles the fan with the
compressor so that the fan does not run all the time.
This saves energy and improves dehumidification.
MoneySaver® will also run to test the temperature
when the off cycle is too long.
constant fan for more air movement. To deactivate
MoneySaver® and go to Constant Fan, press the
MoneySaver® button.

To set mode of operation

3
The unit will automatically be in Cool mode. To go to the next
mode of operation, press the
In order to run the fan by itself, do the following:
4 Continuing from Cool mode, press the System button once
to activate the Fan Only feature.
5 On WY/WE heat-cool models, continuing from Fan Only
mode, press the System button once to activate heat mode.

To adjust temperature

(The unit needs to be in
Cool
6 COOLER – Touch the
7 WARMER – Touch the
Press both the and
the temperature from Fahrenheit (°F) to Celsius (°C).
Repeat these steps to switch from °C back to °F.

To adjust fan speed

8 Touch the Fan Speed button to see the current setting. Touch
it again to change speed. "F1" is the lowest setting
(SLEEP SETTING / LOW), "F2" is MEDIUM, "F3" is HIGH and
"SF" is SmartFan. In SmartFan mode, the fan will automatically
select the fan speed needed to satisfy your desire set point
NOTE: SMART FAN DOES NOT OPERATE IN
CONJUNCTION WITH THE FAN ONLY MODE.
4
e t o y r u F i r d e i r
mode with the temperature
®
Or you may prefer
button.
System
or or
®
MoneySaver Heat
button to lower the room air temperature.
button to raise the room air temperature.
buttons at the same time to switch
h c r o o m a r i
To set the hour clock
9 Touch the Set Hour button to see the current setting. The
number that is displayed is the approximate time (hour only).
Use the
TO SET A.M. AND P.M. ACCORDINGLY. (P.M. is indicated by
a red light in the upper left corner of the display).

To set the timer

NOTE: Set the HOUR CLOCK (Set Hour) before attempting to set
timer functions.
You can set the Start Time and Stop Time a minimum of one hour
apart, and a maximum of 23 hours apart.
After setting the time, press the Set Hour button once (Start
light on). Use the
unit will START.
After selecting the Start Time, press the Set Hour button once.
(Stop Light on). Use the
that the unit will STOP. After selecting the stopping time, press
the Set Hour button once.
10 Press the Timer On/Off button (light turns on) to activate the
timer function. To deactivate this function, press the Timer On/
Off button once again (light turns off). Once the on and off times
have been selected, they will remain in memory and cycle daily
until changed.
NOTE: If the unit is unplugged or the power is interrupted, the HOUR
must be reset or the Timer On/Off will not function when desired.
mode.)
To Re-Activate Money Saver
2 Press the
feature. The light will indicate
Check Filter Light
11 The Check Filter light comes on when the filter needs cleaning.
Press the Check Filter button to reset the timer.
o c d n i t i n o er
and buttons to change the settings. BE SURE
and buttons to select the time that the
and
button to activate the
®
MoneySaver
MoneySaver
buttons to select the time
MoneySaver
®
is in use.
®