To Play Only Desired Tracks/Discs; Program Playback - To Program Tracks/Discs In Desired Order; In The Player - Pioneer PD-F1004 Operating Instructions Manual

3
4
6
3,4
1
2
a
E
PGM
o
,1
E
PROGRAM is
displayed
E
I
(l)
rqoNEcR
Drsc
1 nrcx 1
nm¡
O'OO"
<<
1
PIONEER
PD-F1004
5
F
ILE_TYPE
4
COMPACT
D
ISC
5
ON_SCREEN
INPUT
tru
lñocRÄMl
E
ts
:123
_ OOO
llll4sa
II
II OOO
¡L-Jl Taso
I-J C)OOC:)
/)
SET
DISC
+
E
=
óóð
ll
ll
óðò
lLJl T a s
o
U
C]OOÕ
TT
,1
SET
TRACK
Repeat
3-4
MAIN
INPUT
2
5
8
11
14
17
3
6
9
12
15
18
PROGRAM
(Ð
r¡þñ¡€efr
1
4
7
10
13
16
uoo¡
PROGRAM
l
TCAREì
,l
a
E
/)
TO PLAY ONLY DESIRED TRACKS/DISCS
Program playback
-
To program tracks/discs
in desired order
You can perform this
operation in
either stop or playback mode.
However,
t<<
and
>>l
cannot
be used
to
select tracks
during
playback.
Be sureto select stopor
playback mode before programming.
o
Pressing
>
when the program indicator
is lit
starts program
playback
in
the programmed order.
I
Press
PGM on the remote control
un¡t.
¡
The PGM indicator lights.
trOn
the
screen display, check
the
discs
to
be
programmed.
o Movef
to
r
(upward scrolling)
orv
(downward scrolling)
and
press
O.
E Select the disc number
which conta¡ns the track
to
be programmed
with the digit
buttons,
and
then press the
DISC
SET
button.
To program entire discs, enter the
desired
disc numbers with
the
dig¡t buttons and DISC SET
button, and then go to
step
5.
Make sure that
the player
is in
stop
mode
for Disc programming.
o
When the DISC
SET
button
is
pressed,
"AL"
(all
tracks) appears
on
the
display.
o
When the disc number
is
programmed,
the PGM indicator, the
disc No. and the track No. blink.
o
Only
in
stop mode, you can use the
DISC -/+
buttons. After
selecting the disc
No., press DISC
SET.
E
Enter the track No. to be programmed
with the
digit
buttons and then press the
TRACK
SET
button.
Only in stop mode, you can use
K<
or
>>1.
After selecting
the
track
No., press TRACK
SET.
o
When the track number
is
programmed,
the PGM indicator, the
disc No.
and
the track No. blink.
!Repeat
steps 3 and
4
to program other tracks.
Checking
the input program:
The programmed tracks can be checked on the
screen.
Move
!
to
PROGRAM and
press
O.
o
The program check screen is displayed.
.
Steps
1
to
1B
of the
program are displayed.
o
To
displaysteps
19to36of the program,
movef
to
t
(upward
scrolling)
or
v
(downward
scrolling) and
press @.
o
With
this screen, "
PAUSE"
is
displayed
when pause
is
entered
and
"AL"
is displayed
when
an
entire disc
is entered.
o
To return
tothe
MAIN screen,
move!to
MAIN
and
press @.
EPress
>
.
The tracks
are played
in
the
programmed order.
NOTE:
When the disc number is selected
with
DISC -/+
¡n
step
3,
and
when
the track
is
selected
w¡th
t<<
or
>>t
in
step
4
in
stop
mode, the
displayed disc
No.
or
track
No. is
automatically programmed
if
K<
or
>>t
¡s not
pressed within 2
seconds.
Therefore, be sure
to press DISC
-/+
or K<, >>l
sequentially until
the des¡red disc
No.
or track
No.
appears on the display.
To stop Program
playback, press
r.
r
Programs containing up
to
36
steps
can be created.
o
The program
contents wrll not be erased even
if the power
is turned off.
¡
When DISC
-/+
is pressed in the program
playback
mode, the
program
mode is
cancelled, and
the
program òontents
are cleared. The player
searches
for the
disc in
ALL mode.
¡
When the programmed disc cannot be detected
¡n program
playback
mode,
or
the
programmed track cannot
be detected after the TOC
is
read,
that programmed
step is cancelled.
'***
- nor is
displayed
for
about
3
seconds,
and
the
next step is
played
back.
21
<PRB1 230>
En