Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Blade NANO QX 3d
Summary of Contents for Blade NANO QX 3d
- Page 1 ® READY-TO-FLY...
-
Page 2: Table Of Contents
Transmitter Setup Table ........... 12 all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid Blade Nano QX 3D Box Contents ........4 LED Codes..............13 damage or serious injury. -
Page 3: Blade Nano Qx 3D Specifications
Blade Nano QX 3D Components ❏ Land the model • Bind your transmitter ❏ Unplug the flight battery from the 4-in-1 control unit Airframe – Blade Nano QX 3D Included Included • Familiarize yourself with the controls ❏ Always turn the transmitter off last Motors –... -
Page 4: Installing The Transmitter Batteries (Rtf)
Installing the Flight Battery NOTICE: Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.g., swollen, bent, broken or punctured. 1. Insert the charger into a USB port. The charger only uses power from the USB port, it will not connect to your computer. USB power supplies, such as those used to charge cellular phones, can also be used. -
Page 5: Transmitter And Receiver Binding
Transmitter and Receiver Binding Your RTF transmitter comes prebound to the model. If you need to re-bind, follow the directions below. MLP6DSM Binding Procedure IMPORTANT: Set up your transmitter before binding your transmitter to the aircraft. 1. Disconnect the flight battery from the quadcopter. Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a specific transmitter. -
Page 6: Transmitter Controls
Eleva- Aileron ON/OFF Rudder Throttle Rudder (Left/Right) If you purchased a BNF Nano QX 3D, the channel 5 switch on your transmitter will select flight modes. See the table on the following Elevator (Up/Down) tor Trim Trim Switch Trim Trim... -
Page 7: Transmitter Setup Table
Transmitter Setup Table Transmitter "Model Transmitter Programming Switches and Supported Flight Modes Type" IMPORTANT: Set up your transmitter before binding your transmitter to the aircraft. System Setup Non-Computerized Transmitter Setup (DX4e and DX5e) Before binding a non-computerized transmitter, ensure all servo reversing is set to Switch Select normal and trim is at center. -
Page 8: Understanding The Primary Flight Controls
Understanding the Primary Flight Controls Flying the Nano QX 3D If you are not familiar with the controls of your Nano QX 3D, take a few minutes to familiarize yourself with them before Takeoff attempting your first flight. Increase the throttle until the model is approximately 2 ft. (600mm) off the ground and check the trim so the model flies as desired. -
Page 9: Exploded View
BLH7104 Frame Support: Nano QX 3D EFLH1063 MLP6DSM SAFE Transmitter BLH7101 4-in-1 Control Unit: Nano QX 3D EFLC1013 1S USB Li-Po Charger, 500mAh High Current UMX Connector: Nano QX 3D Optional Parts Part # Description Part # Description EFLC1006 Celectra 1S 3.7v Variable Rate DC Li-Po Charger... -
Page 10: Troubleshooting Guide
Nano QX 3D does not function Flight battery connected with the wrong Replace the 4-in-1 board. Connect the flight bat- The Nano QX 3D is bound to a different Select the correct model memory on the trans- and smells burnt after connecting... -
Page 11: Limited Warranty
Limited Warranty What this Warranty Covers Non-Warranty Service BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. damaged parcels, as Horizon is not responsible for merchan- Further, in no event shall the liability of Horizon exceed the dise until it arrives and is accepted at our facility. An Online Should your service not be covered by warranty, ser- Horizon Hobby, LLC, (Horizon) warrants to the original purchas- individual price of the Product on which liability is asserted. -
Page 12: Warranty And Service Contact Information
(in accordance with ISO/IEC 17050-1) Horizon Service Center servicecenter.horizonhobby. No. HH2015010703 No. HH2015010702 (Repairs and Repair Requests) com/RequestForm/ Product(s): Blade Nano QX 3D BNF Product(s): Blade Nano QX 3D RTF www.quickbase.com/db/ Horizon Product Support United States of 4105 Fieldstone Rd bghj7ey8c?a=GenNewRecord... - Page 13 ©2015 Horizon Hobby, LLC. Blade, E-flite, SAFE, the SAFE logo, DSM, DSM2, DSMX, Bind-N-Fly, the BNF logo, Celectra, ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan.