Sony TRINITRON BVM-A20F1U Operation Manual page 112

[D11] NETWORK SETTINGS... menu
IP ADDRESS: Set the IP address (default is
"192.168.000.001").
SUBNET MASK: Set the subnet mask (default is
"255.255.255.000").
DEFAULT GATEWAY: Set the default gateway on
or off (default setting is OFF).
ADDRESS: Set the default gateway (default is
"---.---.---.--- (no setting)").
CANCEL: Select to cancel the setting.
CONFIRM: Select to save the setting.
Note
When the NETWORK switch is set to PEER TO PEER, the
IP address is set to "192.168.000.001" regardless of the
display on the monitor.
When the NETWORK switch is set to LAN, the IP address
is set to the displayed one.
[D12] SNMP SETTINGS... menu
CONTACT menu: Set the information of the
administrator.
NEW NAME: Enter a new name (up to 20
characters).
The usable symbols are "(", ")", ".", " – ", "+", "/
", "%", "*", "#", "_", "$" and "(space)" (12
symbols).
NAME menu: Set the information for the
administration (device ID).
NEW NAME: Enter a new name (up to 20
characters).
The usable symbols are "(", ")", ".", " – ", "+", "/
", "%", "*", "#", "_", "$" and "(space)" (12
symbols).
LOCATION menu: Set the location information.
NEW NAME: Enter a new name (up to 20
characters).
The usable symbols are "(", ")", ".", " – ", "+", "/
", "%", "*", "#", "_", "$" and "(space)" (12
symbols).
TRAP menu: Set the address to send the information.
TRAP1 and TRAP2 are set.
TRAP1: Set the IP address (default setting is
"000.000.000.000").
TRAP2: Set the IP address (default setting is
"000.000.000.000").
CANCEL: Select to cancel the changed or
confirmed setting.
CONFIRM: Select to save the changed or
confirmed setting.
[D2] PARALLEL REMOTE... menu
PARALLEL REMOTE: Select whether or not to use
the PARALLEL REMOTE functions (OFF or ON)
(default setting is OFF).
44
[D] System Configuration – SYSTEM CONFIGURATION Menu
1 PIN... - 8 PIN...: Assign the function to each pin of
the PARALLEL REMOTE connector when
PARALLEL REMOTE is set to ON. k[D21]
[D21] 1 PIN... - 8 PIN... menu
Assign a function to the selected pin. k[D211]
The factory settings for each pin
1 PIN: CH01
2 PIN: CH02
3 PIN: EXT SYNC
4 PIN: MONO
5 PIN: MARKER
6 PIN: unused
7 PIN: unused
8 PIN: TALLY
[D211] PARALLEL REMOTE menu
PARALLEL REMOTE (1/2) menu
CH01 to 30: Select a channel number. Enter the
desired channel number with the numeric button.
----: Set to unused.
UNDER SCAN: Set under scan on or off.
16:9: Set a 16:9 aspect ratio on or off.
H DELAY: Set the horizontal sync display on or off.
V DELAY: Set the vertical sync display on or off.
EXT SYNC: Set the synchronization to external sync
signals enabled or disabled.
COMB: Set the comb filter on or off.
APERTURE: Set the correction of frequency
characteristics enabled or disabled.
MONO: Set monochrome display on or off.
PARALLEL REMOTE (2/2) menu
BLUE ONLY: Set the blue signal pictures display
(monochrome) on or off.
R OFF: Set cutting red beams enabled or disabled.
G OFF: Set cutting green beams enabled or disabled.
B OFF: Set cutting blue beams enabled or disabled.
CHROMA UP: Set 12 dB up of the chroma setting
value on or off.
MARKER: Set the marker set in the channel on or off.
TALLY: Set tally lamp on or off.
DEGAUSS: Set degaussing on or off.
POWER OFF: Set the monitor power on or standby.
For the pin assignment, see "PARALLEL REMOTE
connector" in Location and Function of Parts on page 12.
[D3] POWER... menu
Set the condition of the monitor when the main power is
turned on or the power is turned on by remote operation.
STANDBY MODE: Select the power-up condition
(OFF or ON) when the MAIN POWER switch is
turned on.