[Network Setup] - Panasonic AJ-PX270 Operating Instructions Manual

Item
[SDI OUT CHAR]
[SDI EDH]
[HD SDI REMOTE]
[DOWNCON MODE]
[DOWNCON SETTING] [DETAIL]
[H.DTL LEVEL]
[V.DTL LEVEL]
[DTL CORING]
[H.DTL FREQ]
[VIDEO OUT]
[VIDEO OUT CHAR]
[VIDEO OUT ZEBRA]
[TC OUT]
[TC OUTPUT REF]

[NETWORK SETUP]

Configure the settings regarding the network.
[4G/LTE PROPERTY] cannot be selected when the setting is not required on the connected 4G/LTE USB modem.
Item
[USB MODE SELECT]
[USB MODE]
Chapter 6 Menu Operations — Menu list
Selects whether to superimpose characters on <SDI OUT> terminal output images.
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [OFF]
Selects whether to superimpose EDH when output from the <SDI OUT> terminal is SD signal (480i and
576i).
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [ON]
Sets whether to use the control function of recording operation for an external device (such as a recorder)
connected to the <SDI OUT> terminal at HD SDI output.
[ON]: Controls the recording operation of the external device.
[OFF]: Does not control the recording operation of the external device.
f Factory setting: [OFF]
Selects the mode of the down converter output signal mode from the <SDI OUT> or <GENLOCK IN/
VIDEO OUT> terminal in HD mode (1080P, 1080i, or 720P).
[SIDE CROP], [LETTER BOX], [SQUEEZE]
f Factory setting: [LETTER BOX]
Turns detail function for the down converter output signal [ON]/[OFF].
[ON], [OFF]
The down converter output signal contains detail components set during HD signal processing.
This setting superimposes the detail components exclusive to down converter output to that signal.
f Factory setting: [ON]
Sets horizontal detail correction level for the down converter output signal.
[0]...[31]
f Factory setting: [8]
Sets vertical detail correction level for the down converter output signal.
[0]...[31]
f Factory setting: [4]
Sets the detail noise removal level.
[0]...[15]
f Factory setting: [1]
Selects the horizontal detail frequency.
[2.5MHz], [3MHz], [3.5MHz], [4MHz], [4.5MHz]
f Factory setting: [3.5MHz]
Selects the <GENLOCK IN/VIDEO OUT> terminal output [ON]/[OFF].
[ON]: Performs output.
[OFF]: Stops output.
f Factory setting: [OFF]
Selects whether to superimpose characters on <GENLOCK IN/VIDEO OUT> terminal output images.
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [ON]
Selects whether the zebra pattern is superimposed over the output video signals from the<GENLOCK IN/
VIDEO OUT> terminal.
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [OFF]
Sets the type of time code output from the <TC IN/OUT> terminal.
[TCG]: Outputs the time code generator value of the camera at all times.
[TCG/TCR]: Outputs the time code generator value for camera image output, and the time code value of
the video being played back for video playback output.
f Factory setting: [TCG]
Sets the output delay of time code output from the <TC IN/OUT> terminal.
[RECORDING]: Outputs the recorded time code with no delay. This is used when performing simultaneous
recording on two cameras with the time code of this camera as the master.
[VIDEO OUT]: Matches to output images.
f Factory setting: [VIDEO OUT]
Sets the camera operation mode when an external device is connected to the USB.
[STORAGE]: Sets the mode to be used with connected devices such as an external hard disk drive.
[DEVICE]: Selects the USB device mode for using P2 cards as mass storage, using computers or other
devices connected via USB 2.0.
f Factory setting: [STORAGE]
Enables/disables the mode selected in [USB MODE SELECT].
[ON], [OFF]
f Factory setting: [OFF]
– 144 –
Description of settings
Description of settings