Subscribe to Our Youtube Channel
Related Manuals for Recsea RDH-OMEM1
Summary of Contents for Recsea RDH-OMEM1
- Page 1 OLYMPUS OM-D E-M1 Waterproof Housing Recsea RDH-OMEM1 MANUAL Please read this manual before use. NTF CORPORATION UH Division http://www.seatool.net...
-
Page 2: Features Of This Product
INTRODUCTION OLYMPUS OM-D E-M1 Waterproof Housing RDH-OMEM1 ※ Thank you for purchasing the RECSEA RDH-OMEM1 Waterproof Housing. ※ To ensure proper and safe use, please thoroughly read this manual. ※ Improper use may cause leakage causing irreparable damage to your digital camera. -
Page 3: Package Contents
Port is removed press again to active the lens release button. ※ 12-50mm Lens Macro Button Lever - For use with OLYPUS M.ZUIKO Digital 12-50mm 1:3.5-6.3 and RECSEA Lens Port SLP-OM1250-FF and Zoom Gear only. CAUTION! Set 12-50mm Lens Macro Button Lever to the up position when installing... - Page 4 ※ Mode Dial Lock - Use to unlock camera mode dial. CAUTION! Turning housing Mode Dial while camera mode dial is locked may cause damage to the housing Mode Dial gear. ※ Flash Open & Close Lever - For use with OM-D E-M1 flash unit. When installing and removing camera with flash unit attached, set flash unit and Flash Open &...
- Page 5 ※ Please refer to camera instruction manual for explanation of various button functions. OPENING AND CLOSING THE BACK COVER ※ Please do the following operations in a clean area with low humidity and dust. To OPEN, press Lock Lever on both sides of the housing while pulling Secure-Latch away from housing back cover.
-
Page 6: Installing Lens Port
※ Please conduct the following operations in a clean area with low humidity and dust. ※ Please perform proper Lens Port O-ring, Housing Port O-ring and contact surfaces maintenance prior to installation. ※ Your RDH-OMEM1 can be used with various Lens Ports and Port Converters, and are compatible with a variety of lenses. CAUTION! Only use the proper Lens Port intended for each lens. -
Page 7: Removing Camera
7. Pull ON/OFF Lever located on the back cover upward as shown in the below image. 8. Set camera aperture lever and housing Lever to the 2 position as shown in the below images. Failing to do so will cause the housing Lever not to function as intended. 9. -
Page 8: Handling Precautions
※ The Accessory Shoe on top of the housing can be used for installation of a target light. Please be mindful of the weight of the light(s) you intend to use. For heavy lights and strobes please use Seatool/Recsea genuine tray and grip assemblies. CAUTION! Damage is irreparable. -
Page 9: Maintenance
CAUTION! Seatool/Recsea STRONGLY recommends the use of Seatool/Recsea genuine tray and grip assemblies listed below under OPTIONS. Leakage or damages due to the use of non-genuine options are NOT covered under warranty. MAINTENANCE CAUTION! Allowing saltwater and contaminants to dry on housing can damage functions and O-rings possibly causing water leakage. -
Page 10: Specifications
1. Using the O-ring Removal Pick, remove O-rings. 2. Clean sand, salt, other contaminants and old grease from O-rings. 3. Clean O-ring grooves and O-ring Contact Surfaces using a clean cotton swab. 4. Visually and physically check each O-rings by running it through finger tips, feeling for cuts, cracks or any other defects that may cause leakage. -
Page 11: Insurance Information
※ For replacement of consumable parts such as O-Rings please contact your dealer or Seatool/Recsea. OPTIONS The following items are optional. Please contact Seatool/Recsea or your local dealer if you wish to purchase. ・INON 45° Viewfinder Unit ・Single Grip & Tray Assembly STG-05L2VL (AL) ・Dual Grip &... -
Page 12: After-Sale Service
※ Warranty does not cover any losses resulting from inoperability of this product, including those related to lost profits or any related expenses. ※ Seatool/Recsea will stock parts necessary for repair for five (5) years from stop of production. ※This product uses some degradable parts, such as buttons and O-Rings. Seatool/Recsea recommends overhauling the housing once per year, more frequently if used often. - Page 13 MEMO...
- Page 14 MEMO...
- Page 15 MEMO...
-
Page 16: Warranty Information
※Dealer: Stamp your company name and contact information, purchase date, model and serial number. Recsea/Seatool Manufacturing & Sales NTF CORPORATION UH Division 390-1 Mii, Midori-Ku, Sagamihara-Shi Kanagawa 252-0151, Japan T: +81 (0)50-7541-0294 F: +81 (0)42-780-5720 http://www.seatool.net E-mail: info@seatool.net...
Need help?
Do you have a question about the RDH-OMEM1 and is the answer not in the manual?
Questions and answers