Subscribe to Our Youtube Channel
Related Manuals for GE ZIC360NXRH
Summary of Contents for GE ZIC360NXRH
- Page 1 Design Guide with Installation Instructions 36” Built-In Bottom-Freezer Refrigerators Pub. No. 49-60468-3 Part No. 224D3095P001 08-13 GE monogram.com...
-
Page 2: Table Of Contents
Proper installation is the responsibility of the installer. Product failure due to improper installation is not IMPORTANT Save these instructions covered under the GE Appliance Warranty. See the for local inspector’s use. Observe all governing codes Owner’s Manual for warranty information. and ordinances. -
Page 3: Dimensions And Clearances
Design Guide DIMENSIONS AND CLEARANCES THE INSTALLATION SPACE 35-1/2" 25-3/8" Framed Models 35" Finished Width 25-3/4" Stainless Steel Models Case Width Case Depth Wall View 2-5/16" cutout width refrigerator can be must be adjusted to fit into a 6" 35-1/2”. ”... -
Page 4: 130° Door Swing
Design Guide Frameless Cabinets: overlaps cabinets at the top and sides. Refrigerator may require filler strips to prevent 23-7/8" From interference with cabinet door swing. Rear of Refrigerator 1" 2" 3" Case 3/4" 1-3/4" 2-3/4" Trim 1-1/2" 2-1/2" 1/2" 1/4" 1-1/4"... -
Page 5: 90° Door Swing
Design Guide Frameless Cabinets: cabinets at the top and Refrigerator cabinets may require Case Trim filler strips to prevent interference with cabinet must allow for filler strips. 23-7/8" From Rear of Refrigerator 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" Door 3/4" Overlay 1/4"... -
Page 6: Customization Basics
Design Guide CUSTOMIZATION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Professional Style Stainless Steel Refrigerators Overlay panels Stainless steel wrapped refrigerators with beveled edges You may also choose to install custom overlay panels from ready for installation. a seamless appearance which integrates smoothly with surrounding cabinetry. -
Page 7: Panel Dimensions
Design Guide 1/4” FRAMED PANEL DIMENSIONS 5/16" Trim If you choose to install framed panels, they must be cut Door Reveal frame on the door, drawer and grille. 1/4" If the custom panel is less than 1/4” thick and if it fits Panel loosely in the door frame, it can be backed up with a piece of filler material or foam tape to improve the fit. -
Page 8: Side Panels
Design Guide SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides of the ” side panels will installation of a framed or overlay grille panel. slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. -
Page 9: Grounding The Refrigerator
Installation Instructions TOOLS REQUIRED MATERIALS REQUIRED ” ” ™ and grille panel ” open-end wrench 1/4” side panels ”, 7/16” socket FLOORING ” open end wrench For proper installation, this refrigerator must be placed on a level surface of hard material that is at the same ”... -
Page 10: Step 1, Remove Packaging
Installation Instructions ” STEP 1 REMOVE PACKAGING bolts securing the straps to the skid. CAUTION: Refrigerator is much heavier at the CAUTION: Remove 5 using a hand truck, handle from side only. base channel OFF SKID. PRUDENCE: bolts on each PRUDENCE: side Remove 2 strap... -
Page 11: Step 3, Install Side Panels
Installation Instructions STEP 4 INSTALL ANTI-TIP BRACKETS STEP 2A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM WARNING: Skip this step when not using an RO System possibility of tipping forward. If the water supply to the refrigerator is from a Reverse ATTENTION: Osmosis Water System, use the refrigerator’s filter bypass the RO filter can result in hollow ice cubes. - Page 12 Installation Instructions STEP 6 ALTERNATE ANTI-TIP STEP 5 LEVEL REFRIGERATOR PROCEDURE by leveling legs, the rear is supported by adjustable The refrigerator must be secured to prevent tipping. wheels. Both are accessible from the front of the The anti-tip brackets cannot be used on metal wall refrigerator.
-
Page 13: Step 8, Adjust Door Swing
Installation Instructions STEP 8 ADJUST DOOR SWING STEP 9 INSTALL GRILLE PANEL NOTE: When space does not allow the door to swing open fully to 130°, you may change the door swing to a 90° opening. Skip this step if door opening is satisfactory for your installation situation. -
Page 14: Step 10, Install Framed Panels
Installation Instructions Right hand models shown. Use the same instructions STEP 10 INSTALL 1/4” FRAMED PANELS for left hand models. IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP 10A. Standard supplied handle shown in 1/4” panel position. Install door and drawer panels: from the door handle. -
Page 15: Step 10A Install Overlay Panels
Installation Instructions STEP 10A INSTALL OVERLAY PANELS Right hand models shown. Use the same instructions for left hand models. Use Front Hol to Secure Hand Use Rear Holes to Secure Trim Supplied handle shown in the overlay panel position. Install door and drawer panels: from the door handle. -
Page 16: Step 13 Start Icemaker
” nut and ferrule (provided) over both ends STEP 13 START ICEMAKER of the copper tubing. Insert tube into the union fitting on the unit and tighten nut to union. GE SmartConnect Tubing: ™ until it is just hand tight. - Page 17 Installation Instructions STEP 14 INSTALL TOEKICK the side of the refrigerator). Install the toekick assembly with the 3 screws provided, adjust to the desired height and tighten the screws. supplied toekick as a template to cut the shape. IMPORTANT: refrigerator cabinet and the top of the toekick must remain unobstructed for proper air circulation.
- Page 18 Notes...
- Page 19 Notes...
- Page 20 For Monogram local service in your area, call ® 1.800.444.1845. NOTE: Product improvement is a continuing endeavor specifications are subject to change without notice. GE Consumer & Industrial Appliances General Electric Company Pub. No. 49-60468-3 Louisville, KY 40225 GEAppliances.com Part No. 224D3095P001 monogram.com...
Need help?
Do you have a question about the ZIC360NXRH and is the answer not in the manual?
Questions and answers